Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2020.08–2021.06
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) U

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  FAIL-SAFE CHART  


FAIL-SAFE FUNCTION


a.

When communication fails in any of the main wires (communication lines) due to a short circuit or other causes, the fail-safe function, which is specified for each system, operates to prevent the system from malfunctioning.


b.

The table below shows the effects on each system when communication is impossible. For further details, refer to each system.

Function Control Master
(Main ECU to determine controls)
System Related Fail-safe Operation Driver Detectable DTC Detection
(ECU that stored DTC)
Engine System Indicator Display
·

Estimates whether the injectors are clogged and requests that a message be displayed informing the user that the injectors need maintenance.

·

Estimates whether the oil has deteriorated and displays a request to change the oil.


ECM Combination meter assembly The meter display cannot be cleared.
When there is a transmission stop or when the bus is continuously detected:
·

The system is unable to inform the user that the oil needs to be replaced.

·

The meter display does not clear.


When there is a reception stop:

The meter display does not clear.


-
Electrical Load Control
(Performs idle up according to the electrical load.)
ECM
·

Air conditioning amplifier assembly

·

Power steering ECU assembly

·

Main body ECU (multiplex network body ECU)


Idle up according to the electrical load is not performed. The idling speed changes. -
Air Conditioning-linked Control
·

Performs idle up according to the compressor load. Performs air conditioning cut control.

·

Performs air conditioning cut control.


ECM Air conditioning amplifier assembly Air conditioning-linked control does not operate (cannot perform idle up). Air conditioning does not operate. -
PTC Heater
(Performs idle up according to requests from the PTC heater [including coolant heater] or heater system.)
ECM Air conditioning amplifier assembly The PTC heater does not operate (permission is not granted).
When there is a transmission stop or when the bus is continuously detected:

The PTC heater does not operate.


When there is a reception stop:
·

The idling speed changes.

·

Heater performance becomes worse.

·

The PTC heater does not operate.


-
Charging Control
(Performs idle up according to charging requests.)
ECM
·

Air conditioning amplifier assembly

·

Main body ECU (multiplex network body ECU)


·

Idle up according to charging requests is not performed.

·

Charging control is not prohibited.


·

Idle up according to charging requests is not performed.

·

The taillights flicker.

·

The blower airflow volume changes.


-
Eco Driving Indicator ECM Combination meter assembly Nothing No information is displayed. -
Integrated Control (VDM)
(Estimates the driver requested torque based on the accelerator pedal operation and performs torque characteristic control according to driving conditions so that driveability, acceleration performance and acceleration feeling are improved.)
ECM
·

Driving support ECU assembly

·

Skid control ECU

·

Power steering ECU assembly

·

Airbag sensor assembly

·

Steering sensor


Does not estimate the driver requested torque based on the accelerator pedal operation and does not perform torque characteristic control according to driving conditions and as a result, driveability, acceleration performance and acceleration feeling are not improved. Does not estimate the driver requested torque based on the accelerator pedal operation and does not perform torque characteristic control according to driving conditions and as a result, driveability, acceleration performance and acceleration feeling are not improved. -
ECT System Indicator
(Displays shift, switch and mode information to the meter.)
ECM Main body ECU (multiplex network body ECU) Nothing ECT system indicators do not illuminate. -
AI-SHIFT Control
(Controls the automatic transmission in order to improve engine braking power and acceleration feel.)
ECM Radio and display receiver assembly (EMVN ECU) AI-SHIFT control does not operate. - -
Neutral Control
(Reduces engine load and performs idle up.)
ECM
·

Skid control ECU

·

Airbag sensor assembly


Neutral control does not operate. - U0129/ U012987
(ECM)
Coast Downshift/Heater Requested Upshift Delay
(Changes the coast downshift point based on the air conditioning load. Performs heater requested upshift delay.)
ECM Air conditioning amplifier assembly Coast downshift does not operate. Coast downshift shock becomes stronger. -
Pre-collision System
(Recognizes obstacles and provides a warning, brake assist and collision avoidance braking.)
Forward recognition camera
·

Millimeter wave radar sensor assembly

·

Skid control ECU

·

Airbag sensor assembly

·

Steering sensor

·

ECM


Cancels the pre-collision brake assist, PCS warning buzzer and PCS pre-collision brake control.
·

The PCS warning light illuminates.

·

Displayed on multi-information display.


·

U010087

·

U012587

·

U012687

·

U012987

·

U015587

·

U023587

·

U023A87

·

U030051

·

U030057

·

U041881


(Forward recognition camera)
Dynamic Radar Cruise Control
(Enables recognition, determination and tracking of the preceding vehicle at an appropriate vehicle-to-vehicle distance until it stops with the milliwave radar, yaw rate sensor, steering angle sensor, etc., and drives the vehicle constantly at a set speed when there is no preceding vehicle forward.)
Forward recognition camera
·

Airbag sensor assembly

·

Steering sensor

·

ECM

·

Combination meter assembly

·

Skid control ECU


Cruise control system is stopped. Displayed on multi-information display.
·

U010087

·

U012587

·

U012687

·

U012987

·

U015587

·

U110687


(Forward recognition camera)
Lane Departure Alert
(Alerts the driver of the possibility of lane departure and performs brake control to assist the vehicle in returning to the center of the road.)
Forward recognition camera
·

Millimeter wave radar sensor assembly

·

Combination meter assembly

·

ECM

·

Skid control ECU

·

Airbag sensor assembly

·

Steering sensor


·

White line recognition is stopped.

·

Stops control requests to skid control ECU.

·

Stops buzzer sounding to combination meter.


·

The lane departure alert indicator light illuminates.

·

Displayed on multi-information display.


·

U010087

·

U012587

·

U012687

·

U012987

·

U015587

·

U023587

·

U030051

·

U030057


(Forward recognition camera)
Road Sign Assist
(Recognizes the sign with the front camera and displays the recognized sign on the meter.)
Forward recognition camera
·

ECM

·

Airbag sensor assembly

·

Skid control ECU

·

Main body ECU (multiplex network body ECU)

·

Combination meter assembly


·

Stops the road sign display.

·

The warning is stopped.


Displayed on multi-information display.
·

U010087

·

U012587

·

U012987

·

U014087

·

U015587


(Forward recognition camera)
TMN
(Detects that the preceding vehicle has started off with the front camera and milliwave radar, and then notifies the driver.)
Forward recognition camera
·

Millimeter wave radar sensor assembly

·

Combination meter assembly

·

ECM

·

Combination meter assembly

·

Skid control ECU


Stops preceding vehicle start notification. Displayed on multi-information display.
·

U010087

·

U012987

·

U015587

·

U023587


(Forward recognition camera)
Forward Recognition Camera System
(Sends the common calculation and recognition result to each application in the forward recognition camera.)
Forward recognition camera
·

Main body ECU (multiplex network body ECU)

·

ECM

·

Skid control ECU

·

Airbag sensor assembly

·

Steering sensor


·

Previous value is maintained.

·

The recognition is invalid.


Nothing
·

U010087

·

U012587

·

U012687

·

U012987

·

U014087


(Forward recognition camera)
TC DTC Output Service
(While TC = ON is being received from the engine, a DTC is output in response to the request from the combination meter assembly.)
Combination meter assembly ECM Ends the TC service when reception of the TC signal is lost during the TC service (TC = ON) and this is regarded as TC = OFF. - -
Timestamp
(Stores the timestamp information received from the main body ECU [multiplex network body ECU] together with the DTC.)
Airbag sensor assembly Main body ECU (multiplex network body ECU) Changes to a separate count inside the ECU and sets separate count recognition information when it receives a fail value or communication stops. - -
Trigger Signal/Self Transmission
(Outputs the airbag sensor assembly signal.)
Airbag sensor assembly Skid control ECU Data is periodically transmitted every 12 ms. - -
Event Data Recorder (EDR)
(Records conditions, such as the vehicle speed, the amount the accelerator is depressed, and the shift lever position when the event data recorder recording conditions are met.)
Airbag sensor assembly
·

ECM

·

Skid control ECU

·

Forward recognition camera

·

Steering sensor

·

Airbag sensor assembly

·

Combination meter assembly


·

Records an invalid value in the EDR.

·

Maintains the previous values.


- -
Drive Data Recorder (DDR)
(Records conditions such as the vehicle speed, the amount the accelerator is depressed, and the shift lever position when the drive data recorder recording conditions are met.)
Airbag sensor assembly
·

Main body ECU (multiplex network body ECU)

·

Forward recognition camera

·

ECM

·

Skid control ECU

·

Power steering ECU assembly

·

Combination meter assembly

·

Steering sensor

·

Airbag sensor assembly


·

Records an invalid value in the DDR.

·

Maintains the previous values.


- -
AACN
(Sends data stored by the event data recorder to the emergency call service.)
Telematics transceiver Airbag sensor assembly
·

Regards the data as invalid.

·

Maintains the previous values.


- -
Door Lock
(Operates the lock and unlock (the key-linked function, key lock-in prevention function, automatic lock function, etc.).)
Main body ECU (multiplex network body ECU)
·

Airbag sensor assembly

·

Combination meter assembly

·

ECM


·

Follows the final information before communication was lost while the ignition switch was ON.

·

Key-linked operation is permitted while the ignition switch off.

·

The speed-sensitive automatic door lock operation is prohibited.

·

The shift-linked automatic door lock operation is prohibited.

·

The shift-linked automatic door unlock operation is prohibited.

·

Automatic door lock switching is prohibited.


-
·

U0100

·

U0101

·

U0151

·

U0155


(Main body ECU [multiplex network body ECU])
Alarm
(Sounds warning)
Main body ECU (multiplex network body ECU) ECM Nothing -
·

U0100

·

U0120


(Main body ECU [multiplex network body ECU])
Automatic Display Dimming
(Controls the display dimming.)
Main body ECU (multiplex network body ECU) Combination meter assembly
·

Dims the display automatically when the switch is not in tail cancel mode.

·

Dims the interior display and indicators when the light sensor illuminance signal value is less than the display dimming value.

·

Control condition: Automatic display dimming control.


- U0155
(Main body ECU [multiplex network body ECU])
Illumination
(Performs illumination control.)
Main body ECU (multiplex network body ECU)
·

Certification ECU (smart key ECU assembly)

·

ECM


·

The dome light turns off.

·

The door mirror foot light is turned off.

·

The foot light is adjusted.


The dome light does not turn off immediately after exiting the vehicle.
·

U0101

·

U0327


(Main body ECU [multiplex network body ECU])
Seat and Mirror Control
(Controls the memory function (the seat, steering wheel, tilt and telescopic and mirror position adjustments).)
Main body ECU (multiplex network body ECU)
·

Front power seat switch (power seat control ECU)

·

Multiplex tilt and telescopic ECU

·

Outer mirror control ECU assembly LH

·

Outer mirror control ECU assembly RH

·

Certification ECU (smart key ECU assembly)

·

Combination meter assembly


·

Commands the seat, tilt and telescopic, etc. to stop operating.

·

Memory function play sequence control

·

Memory call control

·

Return/away control

·

Memory call registration: The operation is stopped due to timing out while waiting for the verification results.


-
·

U0120

·

U0155

·

U0199

·

U0200

·

U0208

·

U0327

·

U1115


(Main body ECU [multiplex network body ECU])
Diagnostic/C-BEST
(Diagnostic phase 4 communication.)
- All ECUs connected to CAN Exits diagnostic mode. - -
Entry/Wireless
(Controls smart/wireless functions.)
Certification ECU (smart key ECU assembly) Certification ECU (smart key ECU assembly)
·

Smart lock/unlock control is not possible.

·

Smart glass hatch open control is not possible.


- U0327
(Main body ECU [multiplex network body ECU])
Light Control
(Controls DRL.)
Main body ECU (multiplex network body ECU) ECM DRL control does not operate. - U0100
(Main body ECU [multiplex network body ECU])
Tire Pressure Monitor Sensor
(Monitors the tire pressure, meter speed, etc. and drives the meter indicator and multi-information display [BERKES-CAN GW].)
Tire pressure warning ECU and receiver Combination meter assembly Initial communication value is sent to the BERKES side. The tire pressure monitor sensor indicator blinks for 1 minute and then stays illuminated. U0155
(Main body ECU [multiplex network body ECU])
Automatic High Beam System
(Controls the high beam output automatically when the smart beam sensor detects a preceding or oncoming.)
Main body ECU (multiplex network body ECU) Forward recognition camera The system does not operate (The meter indicator blinks). The AHB indicator blinks. U023A
(Main body ECU [multiplex network body ECU])
Mirror Control
·

Performs auto electrical mirror control

·

Performs reverse linked mirror control


Main body ECU (multiplex network body ECU)
·

Certification ECU (smart key ECU assembly)

·

ECM

·

Combination meter assembly

·

Outer mirror control ECU assembly LH

·

Outer mirror control ECU assembly RH


·

Auto electrical mirror does not operate (wireless, smart lock/unlock linked function).

·

Operation stop while cranking the engine does not operate.

·

Does not operate the reverse shift-linked mirror function.


-
·

U0100

·

U0155

·

U0199

·

U0200

·

U0327


(Main body ECU [multiplex network body ECU])
Lost Communication Detection
(The NS and NM frames of the ECU connected to the global bus are monitored to detect for ECU communication failures.)
Central gateway ECU (network gateway ECU) ECUs connected to the global bus Stores the communication failure time. - -
Display Dimming
(Performs dimming control for the clearance sonar main switch indicator.)
Clearance warning ECU assembly
·

Clearance warning ECU assembly

·

Main body ECU (multiplex network body ECU)


·

When communication is lost with the ignition switch ON: Operates under default (dim) mode.

·

When there is a communication stop after normal signal reception: Operates according to last status.


- -
Shift Position Judgment
(Receives shift position data which it uses for the clearance sonar detection operation conditions.)
Clearance warning ECU assembly
·

Clearance warning ECU assembly

·

ECM


Changes to an operation state which is used when the shift lever is in P. - U0101
(Clearance warning ECU assembly)
Vehicle Speed Judgment
(Receives vehicle speed data which it uses for the clearance sonar detection operation conditions.)
Clearance warning ECU assembly
·

Clearance warning ECU assembly

·

Combination meter assembly


Changes to an operation state which is used when the vehicle speed is 20 km/h (12 mph) or higher. - U0155
(Clearance warning ECU assembly)
Distance Correction
(Corrects the distance measured by ultrasonic waves using the ambient temperature information.)
Clearance warning ECU assembly
·

Clearance warning ECU assembly

·

Air conditioning amplifier assembly


Changes to an operation state that is used when the ambient temperature is 25°C. - -
PKB Judgment
(For vehicles with a manual transmission, receives PKB information and uses it for the clearance sonar detection operation condition.)
Clearance warning ECU assembly
·

Clearance warning ECU assembly

·

Main body ECU (multiplex network body ECU)


When there is a communication stop, PKB is recognized as "ON". - U0142
(Clearance warning ECU assembly)
Vehicle Information Judgment
(Judges existence of EV/HV vehicle, AT/MT, RHD/LHD or Eco-run, and switches control.)
Clearance warning ECU assembly
·

ECM

·

Main body ECU (multiplex network body ECU)


·

When AT/MT recognition stops: System operates with the previous value.

·

When a stop occurs after the ignition switch is turned to ON: Clearance sonar/intelligent parking assist do not operate.


·

The clearance sonar system does not operate.

·

Displays messages on the multi-information display.

·

The buzzer sounds.


U0100
(Clearance warning ECU assembly)
Door Mirror Foot Light Illumination Control
(Controls the door mirror foot light illumination based on the light illumination request from the main body ECU [multiplex network body ECU].)
·

Outer mirror control ECU assembly LH

·

Outer mirror control ECU assembly RH


Main body ECU (multiplex network body ECU) The door mirror foot light does not operate. The door mirror foot light does not operate. -
Mirror Operation Control
(Controls operation of the mirrors based on mirror switch information from the main body ECU [multiplex network body ECU].)
·

Outer mirror control ECU assembly LH

·

Outer mirror control ECU assembly RH


Main body ECU (multiplex network body ECU) Cannot control the manual mirror operation. Cannot control the manual mirror operation. U0142
(Outer mirror control ECU assembly LH/Outer mirror control ECU assembly RH)
Mirror Heater Control
(Controls the operation of the mirror heaters based on the operation request from the air conditioning amplifier assembly.)
·

Outer mirror control ECU assembly LH

·

Outer mirror control ECU assembly RH


·

Air conditioning amplifier assembly

·

Main body ECU (multiplex network body ECU)


Does not operate the mirror heaters. Does not operate the mirror heaters. U0142
(Outer mirror control ECU assembly LH/Outer mirror control ECU assembly RH)
Electronic Outer Mirror Retraction Control
(Controls the electronic retraction operation of the mirrors based on mirror switch information from the main body ECU [multiplex network body ECU].)
·

Outer mirror control ECU assembly LH

·

Outer mirror control ECU assembly RH


Main body ECU (multiplex network body ECU) Does not operate the electronic mirror retraction function. Does not operate the electronic mirror retraction function. -
Performs reverse linked mirror control
(Controls the reverse-linked operation based on the reverse request information from the main body ECU [multiplex network body ECU].)
·

Outer mirror control ECU assembly LH

·

Outer mirror control ECU assembly RH


Main body ECU (multiplex network body ECU) Does not operate the reverse shift-linked function. Does not operate the reverse shift-linked function. -
Memorization and Recall Control
(Memorizes the position of the mirrors based on the memory request from the main body ECU [multiplex network body ECU], and controls recall operation for the memorized position.)
·

Outer mirror control ECU assembly LH

·

Outer mirror control ECU assembly RH


Main body ECU (multiplex network body ECU)
·

Does not operate the mirror recall function.

·

Does not operate the mirror memorization function.


·

Does not operate the mirror recall function.

·

Does not operate the mirror memorization function.


-
Transfer High-low Switching
(Judges the vehicle speed, T/M information and switches to Transfer High-low according to the switching operation performed by the user.)
4 wheel drive control ECU (4WD control ECU)
·

ECM

·

Skid control ECU

·

Combination meter assembly


·

High-low switching prohibited.

·

The system judges whether switching is possible using the wheel speed control characteristic control when a wheel speed malfunction is detected.


When transfer is switching between high and low:
·

The 4LO indicator does not turn on when switching from Transfer High-Low or when in Low mode.

·

Switching does not operate.

·

The 4LO indicator blinks rapidly.


·

U0100

·

U0122


(4 wheel drive control ECU [4WD control ECU])
Transfer Center Differential Free-Lock Switching
(Judges the vehicle speed, T/M information and switches to Transfer Center Differential Free-Lock according to the switching operation performed by the user.)
4 wheel drive control ECU (4WD control ECU)
·

Skid control ECU

·

Combination meter assembly


·

Transfer center differential free-lock switching prohibited.

·

The system judges whether switching is possible using the wheel speed control characteristic control when a wheel speed malfunction is detected.


When transfer center differential is switching between free and lock or transfer center differential is locked
·

The center differential indicator does not turn on.

·

Switching does not operate.

·

The center differential lock indicator blinks slowly (3 times).


U0122
(4 wheel drive control ECU [4WD control ECU])
Rear Differential Free-Lock Switching
(Judges the vehicle speed and switches to Rear Differential Free-Lock according to the switching operation performed by the user.)
4 wheel drive control ECU (4WD control ECU)
·

Skid control ECU

·

Combination meter assembly


·

Rear differential free-lock switching prohibited.

·

The system judges whether switching is possible using the wheel speed control characteristic control when a wheel speed malfunction is detected.


When the rear differential is switching between free and lock or the rear differential is locked:
·

The rear differential indicator does not turn on.

·

Switching does not operate.

·

The rear differential lock indicator blinks rapidly.


U0122
(4 wheel drive control ECU [4WD control ECU])
2-4 Switching
(The vehicle speed is judged and switching between H2 and H4 according to the switching operation performed by the user.)
4 wheel drive control ECU (4WD control ECU)
·

Skid control ECU

·

Combination meter assembly


·

H2 to H4 switching prohibited.

·

The system judges whether switching is possible using the wheel speed control characteristic control when a wheel speed malfunction is detected.


·

The 4WD indicator does not turn on when switching from H2 to H4 or when in H4 mode.

·

Switching does not operate.

·

The 4WD and 4LO indicator blinks rapidly.

·

Displays messages on the multi-information display.


U0122
(4 wheel drive control ECU [4WD control ECU])
H-L Switching
(Judges the vehicle speed, T/M information and switches to H-L according to the switching operation performed by the user.)
4 wheel drive control ECU (4WD control ECU)
·

ECM

·

Skid control ECU

·

Combination meter assembly


·

H2 to H4 switching prohibited.

·

The system judges whether switching is possible using the wheel speed control characteristic control when a wheel speed malfunction is detected.


·

The 4LO indicator does not turn on when switching from H4 to L4 or when in L4 mode.

·

The 4WD indicator does not turn on when in H4 mode.

·

Switching does not operate.

·

The 4LO indicator blinks rapidly.

·

Displays messages on the multi-information display.


·

U0100

·

U0122


(4 wheel drive control ECU [4WD control ECU])
Wheel Speed Fail Characteristics Control
(Even when there is a wheel speed sensor open circuit (fail-safe), 4WD switching (2-4, H-L and Rear Differential Lock) is performed by the user's operation.)
4 wheel drive control ECU (4WD control ECU)
·

ECM

·

Skid control ECU


H2 to H4 and H4 to L4 switching prohibited.
·

Switching does not operate.

·

The 4LO indicator blinks rapidly.

·

Displays messages on the multi-information display.


U0100
(4 wheel drive control ECU [4WD control ECU])
Vehicle Speed Restriction Function
(The vehicle speed is restricted when the front differential is hot.)
4 wheel drive control ECU (4WD control ECU) Skid control ECU The vehicle speed restriction flag and vehicle speed restriction value is set as the fail-safe value.
·

The buzzer sounds while vehicle speed is restricted.

·

The 4WD indicator blinks rapidly.

·

Displays messages on the multi-information display.


-
KSS
(Opens and closes accumulator valve to suppress roll.)
Stabilizer control ECU
·

ECM

·

Steering sensor

·

Skid control ECU

·

Airbag sensor assembly

·

Main body ECU (multiplex network body ECU)

·

Stabilizer control ECU

·

Combination meter assembly


·

Continues control.

·

Continues control (When YGS communication normal and horizontal G sensor normal).

·

Accumulator valve open (When YGS communication abnormal or horizontal G sensor abnormal).

·

Continues control (When STR communication normal and horizontal steering angle sensor normal).

·

Accumulator valve open (When STR communication abnormal or horizontal G sensor abnormal).

·

The accumulator valve is opened.


·

KDSS light illuminates.

·

Nothing (When STR communication normal and steering sensor normal)

·

KDSS light illuminates (When STR communication abnormal or horizontal G sensor abnormal)


·

U0100

·

U0122

·

U0124

·

U0126


(Stabilizer control ECU)
VFC
(Changes the PS flow rate according to the vehicle state.)
Power steering ECU assembly
·

ECM

·

Skid control ECU

·

Steering sensor

·

4 wheel drive control ECU (4WD control ECU)

·

Suspension control ECU


·

Alternative control is performed when the engine speed information is interrupted.

·

Alternative control is performed when the vehicle speed information is interrupted.

·

Alternative control is performed when the steering angle information is interrupted.

·

Normal control

·

Maintains the previous values.


PPS warning light illuminates.
·

U0100

·

U0126

·

U0129


(Power steering ECU assembly)
AVS
(Variably controls the damping force according to the vehicle input state.)
Suspension Control ECU Radio and display receiver assembly (EMVN ECU)
·

Continues control.

·

When emergency steering control is not used:

-

Set to fail-safe level.

-

Control operation continues except for roll control and navigation coordinated control.


·

When emergency steering control is used:

-

Control performed with damping force set to emergency level


·

Control continued (Role 3 control and L4 mode control is not possible).

·

Controls other than navigation coordinated control are continued.

·

Control continued as though "engine is running".


Displays messages on the multi-information display.
·

U0100

·

U0122

·

U0126

·

U0124

·

U0114


(Suspension control ECU)
Air Suspension
(Variably controls the vehicle height according to the vehicle input state.)
Suspension control ECU
·

Main body ECU (multiplex network body ECU)

·

ECM

·

Skid control ECU

·

Airbag sensor assembly

·

Suspension control ECU


·

Continues control.

·

Fixed at normal vehicle height.

·

Control continued as though "engine is running".


Displays messages on the multi-information display.
·

U0100

·

U0122

·

U0140


(Suspension control ECU)
Anti-lock Brake System Control
(Prevents the wheels from locking during sudden stops.)
Skid control ECU Airbag sensor assembly
During control:
·

After ending backup control (stabilizing the vehicle), the system changes to normal braking and prohibits control.


Other than during control:
·

Control cannot begin.


ABS warning light illuminates.
·

U0073

·

U0114

·

U0124


(Skid control ECU)
Vehicle Stability Control/Traction Control/Vehicle Dynamics Integrated Management Control
·

Suppresses vehicle instability, such as sliding sideways when cornering and wheel slippage when starting off.

·

Performs vehicle integrated control which includes electronic steering control, during vehicle dynamics integrated control.


Skid control ECU
·

ECM

·

Airbag sensor assembly

·

Steering sensor

·

Power steering ECU assembly


During control:
·

After ending backup control (stabilizing the vehicle), the system changes to normal braking and prohibits control.


Other than during control:
·

Control cannot begin.


Slip indicator light illuminates.
·

U0073

·

U0100

·

U0114

·

U0123

·

U0124

·

U0126


(Skid control ECU)
Hill-start Assist Control
·

Maintains the brake oil pressure for 2 seconds when the brake pedal is depressed further.

·

With the vehicle stopped on a slope, maintains the brake oil pressure for 2 seconds when the brake pedal is released when starting off. (Brake pedal does not need to be depressed further.)


Skid control ECU
·

ECM

·

Airbag sensor assembly

·

Steering sensor


During control:
·

After backup control (pressure is decreased), control is prohibited.

·

After ending backup control (pressure reduction control), the system changes to either prohibit control or stops control, and afterwards prohibits control according to the communication state.

·

Control continues, and after normal control finishes, control is prohibited.


Other than during control:
·

Control cannot begin.


Slip indicator light illuminates.
·

U0073

·

U0100

·

U0114

·

U0123

·

U0124

·

U0126


(Skid control ECU)
Leveling
(Adjust the vertical beam axis direction of the headlights according to the pitch angle calculated using the wheel speeds and vehicle height sensor value.)
No. 1 headlight ECU sub-assembly LH
·

Skid control ECU

·

Main body ECU (multiplex network body ECU)


Leveling control stops (beam axis position is stopped at position when malfunction was detected). -
·

U0129

·

U0142


(No. 1 headlight ECU sub-assembly LH)
Leveling Indicator
(Monitors leveling system malfunctions and when a malfunction is detected, sends an indicator illumination request to the meter.)
No. 1 headlight ECU sub-assembly LH Combination meter assembly Maintains the leveling indicator state. - -
Destination Determination
·

Crosschecks the destination set by the factory with the destination information from the CAN bus line.

·

The leveling pitch angle calculation constant and the illumination operations of each light differ according to the destination.


No. 1 headlight ECU sub-assembly LH
·

ECM

·

Main body ECU (multiplex network body ECU)


Nothing -
·

U0100

·

U0142


(No. 1 headlight ECU sub-assembly LH)
Cornering Light
(Turns the cornering light on and off according to the wheel speed, turn, steering angle and shift position data.)
No. 1 headlight ECU sub-assembly LH
·

ECM

·

Skid control ECU

·

Combination meter assembly

·

Steering sensor

·

Main body ECU (multiplex network body ECU)


Stops cornering light control (cornering light turns off). -
·

U0101

·

U0126

·

U0129

·

U0142

·

U0155


(No. 1 headlight ECU sub-assembly LH)
Low Beam, High Beam, DRL (Domestic Default), Clearance, Side Marker (OPT)
(Turns the specified light source on and off according to low beam, high beam, DRL [domestic default], clearance light and side marker light command data.)
Main body ECU (multiplex network body ECU) No. 1 headlight ECU sub-assembly LH Forces the low beams, clearance lights and side marker lights to illuminate. - U0142
(No. 1 headlight ECU sub-assembly LH)
LED Headlight Indicator
(Monitors low beam LED malfunctions and when a malfunction is detected, sends an indicator illumination request to the meter.)
No. 1 headlight ECU sub-assembly LH Headlight light control ECU sub-assembly LH Maintains the LED headlight indicator status. - -
Headlight Cleaner Signal Output
(Outputs the headlight cleaner relay ON signal based on the direct line front washer switch signals, headlight cleaner switch signals, low beam illumination command from the main body ECU [multiplex network body ECU] and IG data.)
No. 1 headlight ECU sub-assembly LH Main body ECU (multiplex network body ECU) Nothing - U0142
(No. 1 headlight ECU sub-assembly LH)
Entry and Start Function
·

Entry lock/unlock and back door unlatch

·

Entry and start warnings

·

Entry illumination (dome light illumination, etc.)

·

Engine start possible display


Certification ECU (smart key ECU assembly) ECM The previous value is maintained. Incorrect entry and start warnings are output. U0100
(Certification ECU [smart key ECU assembly])
Wireless Function
(Operates the wireless lock/unlock functions, etc.)
Main body ECU (multiplex network body ECU)
·

Certification ECU (smart key ECU assembly)

·

Main body ECU (multiplex network body ECU)


Nothing
·

Wireless lock/unlock and trunk functions do not operate.

·

When the ignition switch is ON, the wireless lock/unlock/back open functions do not operate.


U0142
(Certification ECU [smart key ECU assembly])
Engine Switch Lettering Illumination Control
(Operates the engine switch lettering illumination in conjunction with the dome light illumination, etc.)
Certification ECU (smart key ECU assembly)
·

Certification ECU (smart key ECU assembly)

·

Main body ECU (multiplex network body ECU)


·

If the engine switch letters are illuminated due to the dome light, the illumination turns off.

·

When the DC cut fuse is removed and the engine switch letters are illuminated due to the panel illumination, the illumination turns off.

·

The previous value is maintained.


·

If the engine switch letters are not illuminated, they do not illuminate.

·

If the engine switch letters are illuminated due to the panel illumination, the illumination does not turn off.

·

If the engine switch letters are illuminated due to the dome light, the illumination turns off.

·

When the DC cut fuse is removed and the engine switch letters are illuminated due to the panel illumination, the illumination turns off.


U0142
(Certification ECU [smart key ECU assembly])
Security Indicator Display Function
(Displays the immobiliser security condition.)
Certification ECU (smart key ECU assembly)
·

Certification ECU (smart key ECU assembly)

·

Main body ECU (multiplex network body ECU)


Nothing Security condition cannot display normally (illuminates during security warning preparation/security warning). U0142
(Certification ECU [smart key ECU assembly])
Security Indicator Display Function
(Displays the immobiliser security condition.)
Certification ECU (smart key ECU assembly) ECM Nothing The entry and start warnings do not operate properly.
·

The timing for stopping the engine start operation method display when starting the engine is delayed.

·

The smart key portable device low battery warning does not operate when starting the engine.


U0100
(Certification ECU [smart key ECU assembly])
Electronic Engine Switch Control
(Changes the engine switch mode and sends starter drive requests according to engine start switch operation.)
Certification ECU (smart key ECU assembly)
·

Main body ECU (multiplex network body ECU)

·

Skid control ECU

·

ECM

·

Combination meter assembly


Nothing
·

Guidance cannot be displayed.

·

Preheater does not operate.

·

When the engine switch is off, the entry and start system with push button start telltale blinks red according to a "vehicle information malfunction" judgment.

·

Remote engine starter does not operate.


·

U0100

·

U0140

·

U0155


(Certification ECU [smart key ECU assembly])
Steering Sensor
(Detects the steering wheel angle.)
Steering sensor
·

Skid control ECU

·

Combination meter assembly


Data is periodically transmitted every 12 ms. The VSC OFF indicator light turns on. -
Multi-terrain Monitor
(Supports checking of road surface conditions near the vehicle that can easily become driver blind spots by using the camera switch to switch the images captured by the 4 cameras installed on the front, rear and left and right sides.)
Parking assist ECU Parking assist ECU
·

During a transmission malfunction: None (Continuously displayed during camera image display).

·

When bus off is continuously detected:

-

The camera image part becomes black.

-

The color of switches on the screen are toned down.

-

Guide lines and clearance sonar cooperative/RCTA cooperative icons cannot be displayed.



·

During a transmission malfunction: Attention mark is displayed on the screen

·

When bus off is continuously detected:

-

The camera image part becomes black

-

The screen switches are grayed out, and the attention mark is displayed

-

Does not display guide lines and clearance sonar cooperative/RCTA cooperative icons.



U0073
(Parking assist ECU)
Multi-terrain Monitor
(Supports checking of road surface conditions near the vehicle that can easily become driver blind spots by using the camera switch to switch the images captured by the 4 cameras installed on the front, rear and left and right sides.)
Parking assist ECU ECM
When back view and side view in L4 mode and side view in H4 mode are displayed:
·

Camera image display is ended.

·

Display is not switched with shift operation.


When front view and side view in L4 mode and panoramic view and front view in H4 mode are displayed:
·

Continuously displayed

·

Display is not switched with shift operation.


·

Camera image display ends.

·

Camera image is not displayed with shift operation

·

Attention mark is displayed on the camera screen


U0100
(Parking assist ECU)
Parking assist ECU 4 wheel drive control ECU (4WD control ECU)
When L4 mode is displayed:
·

Continuously displayed

·

When displayed again after the display ends, the image is displayed in L4 OFF mode.


When L4 mode is displayed:
·

Continuously displayed

·

When displayed again after the display ends, the image is displayed in L4 OFF mode.


When L4 mode is displayed:
·

Attention mark is displayed on the screen.

·

Displays video when L4 mode is off.


When L4 mode is not displayed:
·

Attention mark is displayed on the screen.


U0114
(Parking assist ECU)
Multi-terrain Monitor
(Supports checking of road surface conditions near the vehicle that can easily become driver blind spots by using the camera switch to switch the images captured by the 4 cameras installed on the front, rear and left and right sides.)
Parking assist ECU Airbag sensor assembly
When L4 mode is displayed:
·

Stops rotation correction display for video from the front camera and uses a roll angle of 0.

·

Stops displaying vehicle tilt.


When L4 mode is not displayed:
·

Nothing


When L4 mode is displayed:
·

Attention mark is displayed on the screen.

·

Does not perform rotation correction for video from the front camera and uses a roll angle status of 0.

·

The vehicle icon is cleared from the vehicle tilt angle display.

·

The roll bar and pitch bar are displayed at 0.


When L4 mode is not displayed:
·

Nothing


U0124
(Parking assist ECU)
Parking assist ECU Steering sensor Estimated course line can no longer be displayed.
·

Attention mark is displayed on the screen.

·

Estimated course line is not displayed.


U0126
(Parking assist ECU)
Parking assist ECU Skid control ECU
When L4 mode is displayed:
·

Slip display is not displayed.


When L4 mode is not displayed:
·

Nothing


When L4 mode is displayed:
·

Attention mark is displayed on the screen.

·

When tire slippage occurs, the slip display does not display.


When L4 mode is not displayed:
·

Nothing


U0129
(Parking assist ECU)
Multi-terrain Monitor
(Supports checking of road surface conditions near the vehicle that can easily become driver blind spots by using the camera switch to switch the images captured by the 4 cameras installed on the front, rear and left and right sides.)
Parking assist ECU Skid control ECU Cancels camera display control when ABS operates.
·

Attention mark is displayed on the screen.

·

When the anti-lock brake system operates, function may display and stop video from the camera.


U0129
(Parking assist ECU)
Parking assist ECU Skid control ECU
When side view in H4 mode is displayed:
·

Camera image display is ended.

·

Display is not switched according to vehicle speed.


When side view in H4 mode is not displayed:
·

Display is not switched according to vehicle speed.


When side view in H4 mode is displayed:
·

Camera image display ends.

·

Does not display side view according to camera switch operation.


When side view in H4 mode is not displayed:
·

Attention mark is displayed on the camera screen

·

Unable to switch video from the camera according to the vehicle speed.


U0129
(Parking assist ECU)
Multi-terrain Monitor
(Supports checking of road surface conditions near the vehicle that can easily become driver blind spots by using the camera switch to switch the images captured by the 4 cameras installed on the front, rear and left and right sides.)
Parking assist ECU Skid control ECU
When L4 mode is displayed:
·

Stops rotation correction display for video from the front camera and uses a roll angle of 0.

·

Stops displaying vehicle tilt.


When L4 mode is not displayed:
·

Nothing


When L4 mode is displayed:
·

Attention mark is displayed on the screen.

·

Does not perform rotation correction for video from the front camera and uses a roll angle status of 0.

·

The vehicle icon is cleared from the vehicle tilt angle display.

·

The roll bar and pitch bar are displayed at 0.


When L4 mode is not displayed:
·

Nothing


U0129
(Parking assist ECU)
Multi-terrain Monitor
(Supports checking of road surface conditions near the vehicle that can easily become driver blind spots by using the camera switch to switch the images captured by the 4 cameras installed on the front, rear and left and right sides.)
Parking assist ECU Main body ECU (multiplex network body ECU)
·

Guide lines cannot be displayed.

·

Fixed to mirror neutral position image (Does not change to the image when the mirror is closed).


·

Attention mark is displayed on the screen.

·

Does not display guide lines.


U0140
(Parking assist ECU)
Parking assist ECU Radio and display receiver assembly (EMVN ECU) Continuously displayed and attention mark is displayed on the screen. Attention mark is displayed on the screen. U0163
(Parking assist ECU)
Parking assist ECU Clearance warning ECU assembly Clearance sonar cooperative display is not displayed.
·

Attention mark is displayed on the screen.

·

Does not display clearance sonar cooperative display.


U1110
(Parking assist ECU)
Wake-up/Sleep Characteristics
(Switches between "normal operation mode (wake up)" and "sleep mode" conditions in conjunction with the other ECUs to reduce the dark current.)
Combination meter assembly Main body ECU (multiplex network body ECU)
·

Ignition switch is turned to ON: Maintains condition.

·

Ignition switch is turned off: Meter is allowed to enter sleep mode.


·

Ignition switch is turned to ON: Maintains condition.

·

ACC OFF when ignition switch is off.


-
Light ON/OFF Timing Chart
(Specifies the meter illumination ON and OFF timing.)
Combination meter assembly ECM Control continues based on the last signal received before the ignition switch is turned off. Lights flicker due to cranking after engine started. -
Dimming Judgment
·

Performs light judgment

·

Uses the result of the dimming judgment for the meter illumination and telltale dimming adjustment (stepless/step).


Combination meter assembly Main body ECU (multiplex network body ECU)
·

During a +B connection or a combination meter wake up: Controls in non-dimming mode.

·

During normal driving: The previous condition maintained before fail-safe.


·

During a +B connection or a combination meter wake up: Controls in non-dimming mode.

·

During normal driving: The previous condition maintained before fail-safe.


-
Speedometer
(Controls the speedometer according to vehicle speed signals.)
Combination meter assembly Skid control ECU Control is performed with input signal set as "0". The speedometer displays "0". U0129
(Combination meter assembly)
Tachometer
(Controls the tachometer according to engine speed signals.)
Combination meter assembly ECM Control is performed with input signal set as "0". The engine speed displays as "0". U0100
(Combination meter assembly)
Fuel Gauge
(Displays remaining fuel amount according to the remaining fuel amount measured in the fuel sender.)
Combination meter assembly
·

Skid control ECU

·

ECM

·

Main body ECU (multiplex network body ECU)


Control is performed with input signal set as "0". Gauge does not operate normally. U0129
(Combination meter assembly)
Coolant Temperature
(Controls the gauge according to the engine coolant temperature signal.)
Combination meter assembly ECM The pointer needle is at the center of the "C" mark or below. The pointer needle is at the center of the "C" mark or below. -
ODO/TRIP Meter
(Displays the ODO/TRIP value according to vehicle speed signals.)
Combination meter assembly Skid control ECU The calculation stopped and the last displayed value remained until the ignition switch is turned off. Display state is maintained.
(Uses previous data without integrating initial data after recovering.)
U0129
(Combination meter assembly)
AT Reverse
(Sounds the buzzer when the shift lever is moved to R while drive torque is being generated.)
Combination meter assembly ECM Control is performed with signal set as "0". The buzzer does not sound. -
Seat Belt Buzzer
(Specifies the conditions for the buzzer sounding when the driver and passenger side seat belts are unfastened.)
Combination meter assembly
·

Main body ECU (multiplex network body ECU)

·

ECM

·

Skid control ECU


Control is performed with signal set as "0".
·

Seat belt considered to be fastened, so buzzer does not sound.

·

Vehicle considered not to be in R, so buzzer continues to sound even when in R.

·

Vehicle considered to be in motion, so buzzer continues to sound even after parking the vehicle while buzzer is sounding

·

The buzzer does not sound.


U0129
(Combination meter assembly)
Brake Buzzer
(Sounds the buzzer (sounds intermittently, once or twice) according to the buzzer operation request signal.)
Combination meter assembly Skid control ECU Control is performed with signal set as "0". The buzzer does not sound. -
LDA Cancel Buzzer
(Sounds the buzzer (sounds intermittently, once or twice) according to the buzzer operation request signal.)
Combination meter assembly Skid control ECU Control is performed with temporary values until the ignition switch is turned off. The last displayed value remains. U023A
(Combination meter assembly)
RSA Buzzer
(Sounds the buzzer (sounds once) according to the RSA buzzer sounding signal.)
Combination meter assembly Forward recognition camera Control is performed with temporary values until the ignition switch is turned off. The last displayed value remains. -
Entry Key Intermittent Buzzer
(Sounds the buzzer (sounds intermittently) according to the buzzer operation request signal.)
Combination meter assembly Certification ECU (smart key ECU assembly) The buzzer does not sound. The buzzer does not sound. -
Preceding Vehicle Start Notification Buzzer
(Sounds the buzzer according to the buzzer operation request.)
Combination meter assembly Forward recognition camera The last displayed value remains. The buzzer does not sound. -
Start While in Motion Information Buzzer (Vehicle rolling prevention)
(Sounds the buzzer as a notification measure when the ignition switch is turned off (ACC ON) due to an emergency stop procedure being performed while driving (vehicle rolling prevention).)
Combination meter assembly Certification ECU (smart key ECU assembly) Control is performed with signal set as "0". The buzzer does not sound. -
Push Operation While in Motion Warning Buzzer (Vehicle rolling prevention)
(If the user mistakenly presses the push start switch while driving, the system warns the user that there is a possibility of the engine stopping if the push operation is continued (vehicle rolling prevention).)
Combination meter assembly Certification ECU (smart key ECU assembly) Control is performed with signal set as "0". The buzzer does not sound. -
P Position Reminder Door Ajar Warning Buzzer
(Sounds the buzzer (sounds continuously) according to the buzzer operation request signal.)
Combination meter assembly Certification ECU (smart key ECU assembly) Control is performed with signal set as "0". The buzzer does not sound. -
LDW Warning Buzzer
(Sounds the buzzer (sounds intermittently) according to the buzzer operation request signal.)
Combination meter assembly Forward recognition camera Control is performed with signal set as "0". The buzzer does not sound. U023A
(Combination meter assembly)
Erratic Driving Rest Alert Buzzer
(Sounds the buzzer (sounds twice) according to the buzzer operation request signal.)
Combination meter assembly Forward recognition camera Control continues based on the last signal received before the ignition switch is turned off. The last displayed value remains. U023A
(Combination meter assembly)
PKB-ON Driving Warning Buzzer
(Sounds the buzzer (sounds intermittently) in accordance to the vehicle speed according to the parking brake state signal.)
Combination meter assembly
·

Skid control ECU

·

Main body ECU (multiplex network body ECU)


Control is performed with signal set as "0". The buzzer does not sound. U0129
(Combination meter assembly)
Door Ajar Driving Warning Buzzer
(Sounds the door ajar driving warning buzzer (sounds intermittently) in accordance to the vehicle speed according to the door courtesy switch state signal.)
Combination meter assembly
·

Skid control ECU

·

Main body ECU (multiplex network body ECU)


Control is performed with signal set as "0".
·

Driver seat side does not sound.

·

Passenger seat side does not sound.

·

Rear RH seat side does not sound.

·

Rear LH seat side does not sound.

·

Back door does not sound.

·

Glass hatch does not sound.


U0129
(Combination meter assembly)
PKB-ON Driving Warning Buzzer
(Sounds the buzzer (sounds intermittently) according to the buzzer operation request signal.)
Combination meter assembly Skid control ECU Control is performed with signal set as "0". The buzzer does not sound. U0129
(Combination meter assembly)
Light Reminder Buzzer
(Sounds the buzzer (sounds continuously) according to the illumination status signal and driver seat courtesy switch signal input.)
Combination meter assembly Main body ECU (multiplex network body ECU) The buzzer does not sound. The buzzer does not sound. -
DPF Buzzer
(Sounds the buzzer (sounds intermittently) according to the buzzer operation request.)
Combination meter assembly ECM The buzzer does not sound. The buzzer does not sound. -
Key Reminder (CAN communication)
(Sounds the buzzer (sounds intermittently) according to the key switch and driver seat courtesy switch signals.)
Combination meter assembly Main body ECU (multiplex network body ECU) The buzzer does not sound. The buzzer does not sound. -
4WD Buzzer
(Sounds the buzzer according to the buzzer operation request.)
Combination meter assembly 4 wheel drive control ECU (4WD control ECU) Control is performed with signal set as "0". The buzzer does not sound. -
Check Engine Buzzer
(Sounds the buzzer according to the buzzer operation request.)
Combination meter assembly ECM Control is performed with temporary values until the ignition switch is turned off. Sounding U0100
(Combination meter assembly)
BEAM Indicator
(Operates the indicator according to the illumination command signal.)
Combination meter assembly Main body ECU (multiplex network body ECU) Display state is maintained. Display state is maintained. -
Turn Hazard Light Output
(Performs turn hazard light illumination control according to the illumination request.)
Combination meter assembly
·

Main body ECU (multiplex network body ECU)

·

Skid control ECU

·

Bus buffer ECU


Control is performed with signal set as "0". Turn hard light does not illuminate. U0129
(Combination meter assembly)
TAIL Indicator
(Operates the indicator according to the illumination command signal.)
Combination meter assembly Main body ECU (multiplex network body ECU) Display state is maintained. Display state is maintained. -
Front Fog light (Telltale)
(Operates the indicator according to the illumination command signal.)
Combination meter assembly Main body ECU (multiplex network body ECU) Display state is maintained. Display state is maintained. -
Rear Fog light Indicator
(Operates the indicator according to the illumination command signal.)
Combination meter assembly Main body ECU (multiplex network body ECU) Display state is maintained. Display state is maintained. -
Front Seat Seat Belt Indicator
(Performs indicator operations according to the driver seat buckle switch signal or passenger seat buckle switch signal input via CAN communication or linear switch operation.)
Combination meter assembly
·

Main body ECU (multiplex network body ECU)

·

ECM

·

Skid control ECU


·

Control is performed with signal set as "0".

·

Last signal state maintained.


·

Last signal state maintained.

·

Vehicle considered to be in motion, so blinking continues even after parking the vehicle while telltale light is blinking.

·

Illuminates only (does not blink).


U0129
(Combination meter assembly)
SIL Indicator
(Operates the indicator according to the illumination command signal.)
Combination meter assembly ECM Not illuminated. Not illuminated. -
AIRBAG (Telltale)
(Operates the indicator according to the illumination command signal.)
Combination meter assembly Airbag sensor assembly Control is performed with signal set as "0". Telltale illuminates U0151
(Combination meter assembly)
SLIP (Telltale)
(Operates the indicator according to the illumination command signal.)
Combination meter assembly Skid control ECU Control is performed using the signal as a temporary value. Telltale illuminates U0129
(Combination meter assembly)
Multi-terrain Select Operation Indicator
(Operates the indicator according to the illumination command signal.)
Combination meter assembly Skid control ECU The last displayed value remains. The last displayed value remains. -
PPS (Telltale)
(Operates the indicator according to the illumination command signal.)
Combination meter assembly Power steering ECU assembly Control is performed using the signal as a temporary value. Telltale illuminates U0131
(Combination meter assembly)
KDSS Indicator
(Operates the indicator according to the illumination command signal.)
Combination meter assembly Stabilizer control ECU Control is performed using the signal as a temporary value. Telltale illuminates -
Clearance Sonar (Telltale)
(Operates the indicator according to the illumination command signal.)
Combination meter assembly Clearance warning ECU assembly Not illuminated. Not illuminated. -
ECO Light/Ambient Light Display (for Eco-navigation)
(Operates the indicator according to the illumination command signal.)
Combination meter assembly ECM Control is performed with signal set as "0". Not illuminated. U0100
(Combination meter assembly)
Go To Service
(Operates the indicator according to the illumination command signal.)
Combination meter assembly ECM Control is performed with signal as a temporary value until the ignition switch is turned off. Telltale illuminates U0100
(Combination meter assembly)
Headlight System (Telltale + Multi-display)
(Operates the indicator according to the illumination command signal.)
Combination meter assembly
·

Main body ECU (multiplex network body ECU)

·

No. 1 headlight ECU sub-assembly LH

·

ECM


The last displayed value remains. The last displayed value remains. U0182
(Combination meter assembly)
Brake Warning (Telltale + Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly Skid control ECU
·

Control is performed using the signal as a temporary value.

·

The last displayed value remains.


·

The telltale light and warning display illuminate.

·

The last displayed value remains.


U0129
(Combination meter assembly)
ABS (Telltale + Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly Skid control ECU Control is performed using the signal as a temporary value. The telltale light and warning display illuminate. U0129
(Combination meter assembly)
TRC OFF (Telltale + Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly Skid control ECU Control is performed using the signal as a temporary value. The telltale light and warning display illuminate. -
LDA (Telltale + Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly Forward recognition camera
·

Control is performed with signal set as "0".

·

Maintains the previous values.


·

Display processing is performed with LDA function available.

·

Display processing turns off.

·

Last signal state


U023A
(Combination meter assembly)
PCS (Telltale + Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly
·

Forward recognition camera

·

Skid control ECU


·

Control is performed with signal set as "0".

·

Last signal state maintained.


·

Telltale illuminates

·

Last signal state maintained.

·

Warning display turns on.


U0129
(Combination meter assembly)
BOS/DSC/ICS (Telltale + Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly ECM Control is performed using the signal as a temporary value.
·

Telltale illuminates

·

Warning display turns on.


-
Entry System Display (Telltale + Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly
·

Main body ECU (multiplex network body ECU)

·

Certification ECU (smart key ECU assembly)


The last displayed value remains. The last displayed value remains. -
OIL PRESSURE (Telltale + Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly ECM
·

Control is performed with signal set as "0".

·

Control is performed using the signal as a temporary value.


·

May illuminate while engine stop and start system is operating.

·

Illumination judgment processing is 0.3 second slower than normal while the engine is off.


U0100
(Combination meter assembly)
Tire Pressure Warning (Telltale + Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly Main body ECU (multiplex network body ECU) The last displayed value remains. The last displayed value remains. U0142
(Combination meter assembly)
DOOR (Telltale + Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly
·

Skid control ECU

·

Main body ECU (multiplex network body ECU)


·

Control is performed with signal set as "0".

·

The last displayed value remains.


·

The warning display while stopped illuminates even when the door is opened while driving.

·

The last displayed value remains.


U0129
(Combination meter assembly)
OIL LEVEL (Telltale + Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly
·

ECM

·

4 wheel drive control ECU (4WD control ECU)


·

Control is performed with signal set as "0".

·

Control is performed using the signal as a temporary value.


May mistakenly illuminate. U0100
(Combination meter assembly)
MAINT REQD (Telltale + Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly ECM Control is performed using the signal as a temporary value.
·

Controls with function stopped

·

The last displayed value remains.

·

Display is blank.


-
RSA (Road Sign Assist) (Multi-display+Buzzer)
(Performs display processing according to the signal.)
Combination meter assembly Forward recognition camera Control is performed using the signal as a temporary value.
·

Not displayed.

·

No effect on display.

·

Display the initial value.

·

The buzzer does not sound.


-
AT Fluid Temperature (Telltale + Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly ECM Control is performed with the drivable flag = ON. May mistakenly illuminate. U0100
(Combination meter assembly)
Urea SCR System Warning Display (Telltale + Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly ECM
·

The last displayed value remains.

·

Control is performed using the signal as a temporary value.


·

The last displayed value remains.

·

Display is blank.


-
Check Engine
(Performs display processing according to the signal.)
Combination meter assembly ECM Control is performed with signal as a temporary value until the ignition switch is turned off. MIL (Check malfunction indicator lamp) illuminates. U0100
(Combination meter assembly)
Drive Monitor (Common Specification)
(Performs display processing according to the signal.)
Combination meter assembly
·

Main body ECU (multiplex network body ECU)

·

Skid control ECU

·

ECM


·

The last displayed value remains.

·

Calculation stopped


·

The last displayed value remains.

·

Calculation stopped


·

U0100

·

U0129


(Combination meter assembly)
Ambient Temperature
(Performs display processing according to the signal.)
Combination meter assembly Air conditioning amplifier assembly Displays as "E". Displays as "E". -
Road Surface Ice Display
(Performs display processing according to the signal.)
Combination meter assembly Air conditioning amplifier assembly Control is performed using the signal as a temporary value. Not displayed. -
Eco Drive Indicator Zone Display
(Performs display processing according to the signal.)
Combination meter assembly ECM Control is performed using the signal as a temporary value. Not displayed. U0100
(Combination meter assembly)
Speedometer (Numerical Display)
(Performs display processing according to the signal.)
Combination meter assembly Skid control ECU Control is performed with signal set as "0". Displays as "0". U0129
(Combination meter assembly)
Shift Display
(Performs display processing according to the signal.)
Combination meter assembly ECM
·

When indicators can be simultaneously illuminated: All illuminated according to data.

·

When indicators cannot be simultaneously illuminated (1-character display, etc.): Display turned off.

·

The shift display, mode indicator display and range (gear position) display turned off.


·

When indicators can be simultaneously illuminated: All illuminated according to data.

·

When indicators cannot be simultaneously illuminated (1-character display, etc.): Display turned off.

·

The shift display, mode indicator display and range (gear position) display turned off.

·

No effect on display.


-
Tire Pressure Display (Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly Main body ECU (multiplex network body ECU)
·

Control is performed using the signal as a temporary value.

·

Control is performed with signal set as "0".

·

The last displayed value remains.


·

Tire pressure does not display (4 wheels or spare tire).

·

Tire pressure inverted display does not display (4 wheels or spare tire).

·

Last signal state

·

Units do not display.

·

Interrupt display does not display when tire pressure decreases.


-
Air Suspension Display (Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly Suspension control ECU The last displayed value remains. The last displayed value remains. -
Multi-terrain Select (Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly
·

Skid control ECU

·

4 wheel drive control ECU (4WD control ECU)

·

ECM


·

Display is blank.

·

The last displayed value remains.

·

Control is performed with signal set as "0".


·

Display is blank.

·

The last displayed value remains.

·

May mistakenly display.


U0129
(Combination meter assembly)
Steering Angle Display (Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly Steering sensor Tires do not display. Tires do not display. -
Air Suspension Check Display (Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly Suspension control ECU The last displayed value remains. The last displayed value remains. -
Clearance Sonar (Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly Clearance warning ECU assembly
·

S witch display, guidance instructions display

·

Control is performed with signal set as "0".


·

S witch display, guidance instructions display

·

Control is performed with signal set as "0".


-
TMN Preceding Vehicle Start Notification
(Performs display processing according to the signal.)
Combination meter assembly Forward recognition camera Not displayed. Not displayed. -
LDA Warning Method Change (Software Switch)
(Displays the set value and outputs the CAN signal to switch the setting of the receiving ECU.)
Combination meter assembly Forward recognition camera
·

Control is performed with signal set as "0".

·

The last displayed value remains.


·

Not displayed.

·

The last displayed value remains.


U023A
(Combination meter assembly)
Entry Unlock Mode Setting Display (Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly Certification ECU (smart key ECU assembly) Not displayed. Not displayed. -
Sliding Roof Open Warning (Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly Main body ECU (multiplex network body ECU) The last displayed value remains. The last displayed value remains. -
Tire Pressure Display (Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly
·

Skid control ECU

·

Steering sensor

·

4 wheel drive control ECU (4WD control ECU)


·

Display control

·

No display control (Angle of front tires is 0°)

·

No display control (Tires not displayed)

·

Last signal state


·

Display control

·

No display control (Angle of front tires is 0°)

·

No display control (Tires not displayed)

·

Last signal state


-
PKB-ON Driving Warning (Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly
·

Skid control ECU

·

Main body ECU (multiplex network body ECU)


·

Control is performed with signal set as "0".

·

The last displayed value remains.


·

Not displayed.

·

The last displayed value remains.


U0129
(Combination meter assembly)
Intrusion Sensor Operation Display (Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly Main body ECU (multiplex network body ECU) Not displayed. Not displayed. -
LDA Warning Timing Change (Software Switch)
(Displays the set value and outputs the CAN signal to switch the setting of the receiving ECU.)
Combination meter assembly Forward recognition camera
·

The set value is not displayed.

·

Outputs the signal as "0".


Does not display the set value. U023A
(Combination meter assembly)
SWS Erratic Driving Warning ON/OFF (Software Switch)
(Displays the set value and outputs the CAN signal to switch the setting of the receiving ECU.)
Combination meter assembly Forward recognition camera
·

The set value is not displayed.

·

Outputs the signal as "0".


Does not display the set value. U023A
(Combination meter assembly)
SWS Erratic Driving Warning Sensitivity Change (Software Switch)
(Displays the set value and outputs the CAN signal to switch the setting of the receiving ECU.)
Combination meter assembly Forward recognition camera
·

The set value is not displayed.

·

Outputs the signal as "0".


Does not display the set value. U023A
(Combination meter assembly)
RSA (Software Switch)
(Displays the set value and outputs the CAN signal to switch the setting of the receiving ECU.)
Combination meter assembly Forward recognition camera
·

The set value is not displayed.

·

The last displayed value remains.


Does not display the set value. -
BSM ON/OFF (Software Switch)
(Displays the set value and outputs the CAN signal to switch the setting of the receiving ECU.)
Combination meter assembly Blind spot monitor sensor LH
·

The set value is not displayed.

·

Outputs the signal as "0".


Does not display the set value. -
PCS Warning ON/OFF (Software Switch)
(Displays the set value and outputs the CAN signal to switch the setting of the receiving ECU.)
Combination meter assembly Forward recognition camera
·

The set value is not displayed.

·

Outputs the signal as "0".


Does not display the set value. U023A
(Combination meter assembly)
PCS Erratic Driving Warning Sensitivity Change (Software Switch)
(Displays the set value and outputs the CAN signal to switch the setting of the receiving ECU.)
Combination meter assembly Forward recognition camera
·

The set value is not displayed.

·

Outputs the signal as "0".


Does not display the set value. U023A
(Combination meter assembly)
TMN ON/OFF Software Switch
(Displays the set value and outputs the CAN signal to switch the setting of the receiving ECU.)
Combination meter assembly Forward recognition camera Not displayed. Not displayed. -
TMN Transition Timing Change Software Switch
(Displays the set value and outputs the CAN signal to switch the setting of the receiving ECU.)
Combination meter assembly Forward recognition camera Not displayed. Not displayed. -
Crawl Control Switch Illumination ON/OFF Control
(Operates the switch illumination on and off according to the signal.)
Combination meter assembly Skid control ECU
·

The set value is not displayed.

·

Control is performed with input signal set as "0".


Not illuminated. U0129
(Combination meter assembly)
Multi-terrain Select Switch Illumination ON/OFF Control
(Operates the switch illumination on and off according to the signal.)
Combination meter assembly Skid control ECU The last displayed value remains. The last displayed value remains. -
Rental Car Mode Display
(Displays the driving distance (ODO) when the user enters or exits the vehicle.)
Combination meter assembly
·

Main body ECU (multiplex network body ECU)

·

Forward recognition camera


Ignition switch turned ON:
·

Control is performed with the ignition switch turned to ACC.

·

Last signal state

·

Signal state maintained.


When the ignition switch is off:
·

Control is performed with the ignition switch turned off.

·

Control is performed with the driver seat courtesy signal set as "OFF".

·

Control is performed with the PKB switch signal set as "ON".


Does not operate normally. -
Inclination Monitor (Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly
·

Skid control ECU

·

Airbag sensor assembly


·

SPav averaging process stopped.

·

Displays fail-safe.


·

Does not operate normally.

·

Displays fail-safe.


U0129
(Combination meter assembly)
CDY Mode Display
(Performs display processing according to the signal.)
Combination meter assembly ECM Last signal state maintained. Last signal state maintained. -
Millimeter Wave Radar Adjustment Mode Notification
(Performs display processing according to the signal.)
Combination meter assembly Forward recognition camera Last signal state maintained. Last signal state maintained. -
Electronical Component Operation Restriction Notification (Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly Air conditioning amplifier assembly Last signal state maintained. Last signal state -
AVS Mode (Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly Suspension control ECU Last signal state maintained. Last signal state -
DMS Mode (Multi-display)
(Performs display processing according to the signal.)
Combination meter assembly ECM Last signal state maintained. Last signal state -
Language-linked
(Multi-media-linked)
Combination meter assembly Radio and display receiver assembly (EMVN ECU) Control is performed using the last signal received. The last displayed value remains. U0163
(Combination meter assembly)
Accent Color (Multi-media-linked)
(Multi-media-linked)
Combination meter assembly Radio and display receiver assembly (EMVN ECU) Control is performed using the last signal received. The last displayed value remains. U0163
(Combination meter assembly)
Blind/Spot/Detection
(Detects neighboring vehicles that are in outer mirror blind spots and notifies drivers of the existence of these vehicles.)
Blind Spot Monitor Sensor LH
·

Skid control ECU

·

Steering sensor

·

ECM

·

Main body ECU (multiplex network body ECU)

·

Blind spot monitor sensor LH


The last displayed value remains.
·

BSM indicator illuminates (amber).

·

Displayed on multi-information display.


·

U0100

·

U0126

·

U0129

·

U0142


(Blind Spot Monitor Sensor LH)
Automatic Wheel Position Display
(Links the tire pressure warning valve and transmitter ID with tire positions based on the wheel speed count from the brakes.)
Tire pressure warning ECU and receiver Skid control ECU Cannot stop DTC registration auto location control. Nothing U0129
(Tire pressure warning ECU and receiver)
Air Conditioning Control
·

Adjusts the air temperature, airflow mode and airflow volume according to the engine coolant temperature.

·

Performs the engine coolant temperature map calibration and switches compressor lock judgment value based on engine type.


Air conditioning amplifier assembly ECM
·

While the ignition switch is ON, control is performed using the default engine coolant temperature value (80°C [176°F]).

·

While the ignition switch is ON, control is performed using the default engine type.


Nothing U0100
(Air conditioning amplifier assembly)
Compressor Control
(Determines whether the compressor is locked according to NE.)
Air conditioning amplifier assembly ECM While the ignition switch is ON, control is performed using the default value. Nothing U0100
(Air conditioning amplifier assembly)
Operation Control
·

Controls the operation according to the viscous heater operation permission information.

·

Controls the operation according to the PTC heater operation permission information.


Air conditioning amplifier assembly ECM Permission information (while the ignition switch is ON): Control is performed with the operation prohibited. Nothing U0100
(Air conditioning amplifier assembly)
Panel Control
·

Controls the air conditioning system operation condition and the panel switch IND output according to the panel switch operation information.

·

Determines the availability of exhaust gas automatic recirculation and switches recirculation control according to exhaust gas availability information.


Air conditioning amplifier assembly Radio and display receiver assembly (EMVN ECU) Nothing While the ignition switch is ON, the air conditioning operation state cannot be changed. -
Panel Dimming Control
(Outputs dimming information to the LIN panel according to the display dimming information.)
Air conditioning amplifier assembly Main body ECU (multiplex network body ECU) While the ignition switch is ON, previous values are maintained (during a reset, dimming control is performed). Cannot switch between dimming states (after a reset is performed, the system stays in dimming mode) -
Destination Determination Control
(Switches the A/C control pattern according to the destination information.)
Air conditioning amplifier assembly Main body ECU (multiplex network body ECU) While the ignition switch is ON, previous values are maintained. - U0142
(Air conditioning amplifier assembly)
Ambient Temperature Calibration Control
(Changes the air conditioning system operation condition and adjusts the ambient temperature display value according to the vehicle speed information)
Air conditioning amplifier assembly Combination meter assembly While the ignition switch is ON, control is performed with the default vehicle speed value.
·

The accuracy of the displayed outside temperature becomes less reliable.

·

The system is not able to adjust the air conditioning airflow volume correctly.


U0155
(Air conditioning amplifier assembly)
Air Conditioning Eco Control
(Performs Eco-mode control.)
Air conditioning amplifier assembly ECM While the ignition switch is ON, control is performed using the default value. - -
Air Conditioning Control
(Controls the air conditioning functions.)
Radio and display receiver assembly (EMVN ECU) Air conditioning amplifier assembly
·

The air conditioning related indicators are turned off.

·

If the set air temperature is displayed on an external display device, the set air temperature display is cleared.


-
·

U0073

·

U0164


(Radio and display receiver assembly [EMVN ECU])
Eco Navigation Display
(Displays the average fuel consumption history and a graph that displays fuel consumption and amount of energy recovered per minute.)
Radio and display receiver assembly (EMVN ECU)
·

ECM

·

Skid control ECU

·

Combination meter assembly


·

Fuel consumption calculation cannot start. Discards the calculated value and counts again for 1 minute after receiving normal data.

·

Discards the calculated value and counts again for 1 minute after receiving normal data.

·

Fuel consumption display scale and drive monitor units are displayed using the value of the last received signal.

·

Current fuel consumption, average vehicle speed after start, time elapsed after start and estimated distance to empty are not displayed.

·

Previous received values are displayed for the fuel consumption in intervals.Not displayed if there is no previous received data.


·

The 1 minute fuel consumption graph on the Eco navigation (Eco driving) screen is not updated for 1 minute or more.

·

Fuel consumption display scale and drive monitor units are displayed using the value of the last received signal.

·

Current fuel consumption, average vehicle speed after start, time elapsed after start and estimated distance to empty are not displayed.

·

Previous received values are displayed for the fuel consumption in intervals. Not displayed if there is no previous received data.


·

U0073

·

U0100

·

U0129

·

U0155


(Radio and display receiver assembly [EMVN ECU])
Rear View Monitor Control
(Displays the rear camera view.)
Radio and display receiver assembly (EMVN ECU) ECM Changes to the multi-media display DTC user screen only during camera mode (camera screen release).
·

Changes to the multi-media display user screen only during camera mode (displays camera screen).

·

Cannot switch to the camera screen.


-
Smart Camera Function
(Superimposes the estimated course lines of the vehicle, vehicle width extension lines and distance guide lines over the rear camera image on the display when the vehicle is driven in reverse.)
Radio and display receiver assembly (EMVN ECU) ECM
·

Changes to the multi-media display user screen or multi-media display DTC screen only during camera DTC mode (camera DTC: screen release).

·

Only when camera malfunction DTC C1610 is output: The current DTC (C1610) is cleared.

·

The temporary values for the reactive force setting completion notification and pointer coordinates are sent. The camera screen pattern is treated as a temporary value, and the reaction force setting operates at camera image release.


·

The camera diagnostic screen is displayed.

·

Changes to the multi-media display user screen only during camera mode (displays camera screen).


·

U0073

·

U0265


(Radio and display receiver assembly [EMVN ECU])
Monitoring Function
(ECUs for the multiple camera system, etc.)
Radio and display receiver assembly (EMVN ECU) Parking assist ECU
·

Only when camera diagnostic mode is active: The multi-media display user or diagnostic screen is changed to.

·

Only when camera malfunction DTC C1610 is output: The current DTC (C1610) is cleared.

·

The temporary values for the reactive force setting completion notification and pointer coordinates are sent. The camera screen pattern is treated as a temporary value, and the reaction force setting operates at camera image release.


·

Displays the camera diagnostic screen.

·

Changes to the MM user screen only during camera mode (displays camera screen).


·

U0073

·

U023B


(Radio and display receiver assembly [EMVN ECU])
Destination Determination
(Uses the destination information [include steering wheel information] to determine the driver seat or passenger seat and to determine whether the XM function is enabled.)
Radio and display receiver assembly (EMVN ECU) Main body ECU (multiplex network body ECU) The destination is determined according to the last received value and the system is operated accordingly (if there is no last received value, the system operates using the default value). The time zone and language selection screens do not match the destination.
·

U0073

·

U0140


(Radio and display receiver assembly [EMVN ECU])
Navigation Coordinated Control
(Predicts the road conditions based on the curve and inclination information and appropriately shifts gears according to conditions set by the driver, etc.)
Nothing Nothing AT/CVT coordinated control related information (curve information, etc.) is sent as the initial value. Menu settings for AT/CVT coordinated control ("Strength Level", "Gear Position Display") are cleared.
·

U0073

·

U0100


(Radio and display receiver assembly [EMVN ECU])
Navigation Coordinated Control (Suspension)
(Improves maneuvering stability by controlling the AVS damping force and electric stabilizer based on the forward curve curvature radius information detected by the navigation ECU.)
Radio and display receiver assembly (EMVN ECU) Suspension control ECU Bump learning processing is prohibited. Bump data during learning is discarded.
However, bump data learned so far is maintained, and bump notification processing is performed based on that information.
Menu settings for suspension coordinated control are cleared.
·

U0073

·

U0132


(Radio and display receiver assembly [EMVN ECU])
Navigation Coordinated Control (Air Conditioning)
(Automatically switches between fresh air mode to recirculated air mode based on information from the navigation indicating whether the vehicle is in a tunnel.)
Radio and display receiver assembly (EMVN ECU) Air conditioning amplifier assembly Nothing Menu settings for air conditioning coordinated control (control for changing air conditioning from fresh air mode to recirculated air mode when entering tunnel) are cleared.
·

U0073

·

U0164


(Radio and display receiver assembly [EMVN ECU])
Vehicle Customize Function
(Allows changing of operation and control conditions for vehicle functions [illumination time, etc.].)
Radio and display receiver assembly (EMVN ECU)
·

Air conditioning amplifier assembly

·

Main body ECU (multiplex network body ECU)

·

Certification ECU (smart key ECU assembly)

·

Front power seat switch (power seat control ECU)


When an application that uses Phase 4 remote communication is performed (customize or remote diagnosis), the information is processed regardless of whether the main body ECU (multiplex network body ECU) has permitted or prohibited remote communication. Nothing -
3 retries are performed (including the first time).
·

Grays out and prohibits operation of the applicable customization item.

·

The applicable customization item is not displayed.


·

B15F5

·

B15F6

·

B15F7

·

B15F8


(Radio and display receiver assembly [EMVN ECU])
·

The entrance button is grayed out and cannot be selected when a communication stop occurs, even when customize information is received 1 or more times within 5 seconds after the ignition switch is turned to ON.

·

Customization is performed for the applicable customization item according to diagnostic communication when customize information is not received within 5 seconds after the ignition switch is turned to ON.


The entrance button is grayed out and selection is no longer possible. U0073
(Radio and display receiver assembly [EMVN ECU])
ESPO
(Displays the level of "Eco" driving.)
Radio and display receiver assembly (EMVN ECU)
·

ECM

·

Skid control ECU


·

The eco level meter display is cleared when a communication stop occurs. Generates new display data and restores functionality after recovery.

·

The idling display is cleared when a communication stop occurs. Generates new display data and restores functionality after recovery.

·

Current trip data is discarded when a communication stop occurs. Generates new trip data and restores functionality after recovery.


Nothing U0073
(Radio and display receiver assembly [EMVN ECU])
Brake Hold Operation Control
(Uses the brake hold operation signal to make driving regulation judgments for the currently viewed video mode [TV, DVD-Video, DVD-VR, iPod Video and VTR]. [Allows videos to be displayed when the vehicle is stopped according to brake hold operation.])
Radio and display receiver assembly (EMVN ECU) Skid control ECU The screen display is cleared and the screen is changed to the home screen if a communication stop occurs while video is being displayed. The driving regulation continues to be displayed, if a communication stop occurs while video is being displayed.
·

U0073

·

U0129


(Radio and display receiver assembly [EMVN ECU])
Meter-linked Function
(Changes the display based on the customization information set on the combination meter assembly. Outputs customization information set on own system.)
Radio and display receiver assembly (EMVN ECU) Combination meter assembly
·

Language, unit and accent color linking: Maintains the last valid state.

·

GS search: Control is performed as if there is an unconfirmed GS search request.

-

The last set value is maintained.

-

If the set value is displayed, it is grayed out so that the value cannot be changed.



Function linking with combination meter assembly cannot be operated.
·

U0073

·

U0155


(Radio and display receiver assembly [EMVN ECU])
Information Volume Adjustment or Stop Function
(Receives flags from the driving support ECU to operate the alarm and mutes multi-media audio while the alarm is in operation.)
Radio and display receiver assembly (EMVN ECU) Forward recognition camera Cancels audio mute. - U0073
(Radio and display receiver assembly [EMVN ECU])
Predictive Eco Support Radio and display receiver assembly (EMVN ECU) Skid control ECU
·

The stored information is prohibited from updating.

·

Performs display processing according to the signal.

·

The predictive information is prohibited from sending.


-
·

U0073

·

U0129


(Radio and display receiver assembly [EMVN ECU])
DMS
(Enables selection of the vehicle control operation mode while driving.)
Radio and display receiver assembly (EMVN ECU) Central gateway ECU (network gateway ECU)
·

DMS customize entrance button is not displayed.

·

Exits the setting screen when it is displays.


DMS customize entrance button is not displayed. U0073
(Radio and display receiver assembly [EMVN ECU])
Vehicle Warning Detail Display Radio and display receiver assembly (EMVN ECU)
·

Combination meter assembly

·

ECM

·

Air conditioning amplifier assembly


·

When communication with the applicable ECU is lost before a warning is issued, the warning is unconfirmed.

·

When communication with the applicable ECU is lost after a warning is issued, the warning is confirmed as having taken place after a certain amount of time has elapsed following a recovery of communication.


- U0073
(Radio and display receiver assembly [EMVN ECU])
Seat Adjustment Function
(Seat adjustment is possible on the radio and display receiver assembly (EMVN ECU) screen.)
Radio and display receiver assembly (EMVN ECU) Front power seat switch (power seat control ECU) Changes to the normal screen. -
·

U0208

·

U0209


(Radio and display receiver assembly [EMVN ECU])
Clock Function Radio and display receiver assembly (EMVN ECU) Combination meter assembly Time display is not displayed. - -
Eco Navigation Display
(Displays the fuel consumption in 1 minute intervals, and displays the average fuel consumption history. )
Radio and display receiver assembly (EMVN ECU)
·

ECM

·

Combination meter assembly

·

Skid control ECU


·

Stops updating the fuel consumption displayed in 1 minute intervals on the Eco navigation (Eco driving) display (the graph of fuel consumption in 1 minute intervals that was displayed up until the point of the malfunction is not cleared).

·

Stops updating the average fuel consumption display on the Eco navigation (Eco driving) screen.

·

If the "distance to empty" is being displayed on the Eco navigation (Eco driving) screen, the numbers of the distance to empty are cleared because distance to empty data is lost.


·

The 1 minute fuel consumption graph on the Eco navigation (Eco driving) screen is not updated for 1 minute or more.

·

The most recent value for the graph for fuel consumption in intervals on the Eco navigation (Eco driving) screen is cleared.

·

The numbers of the distance to empty displayed on the graph of fuel consumption in intervals screen of the Eco navigation (Eco driving) are cleared.


·

U0100

·

U0129

·

U0155


(Radio and display receiver assembly [EMVN ECU])
BGM Control
(Determines the destination based on the destination symbol and destination package information and selects the display settings such as the display language and time zone.)
Radio and display receiver assembly (EMVN ECU)
·

ECM

·

Skid control ECU

·

Steering sensor

·

Main body ECU (multiplex network body ECU)


·

If a communication stop occurs when the expected course lines are being displayed, the expected course lines are cleared and "Guidance is not possible" is displayed on the bottom of the screen.

·

If a communication stop occurs when the display is in parallel parking guide mode, "Guidance is not possible" is displayed on the bottom of the screen.


·

If a communication stop occurs when the expected course lines are being displayed, the expected course lines are cleared and "Guidance is not possible" is displayed on the bottom of the screen.

·

If a communication stop occurs when the display is in parallel parking guide mode, "Guidance is not possible" is displayed on the bottom of the screen.

·

Cannot switch to the camera screen.

·

When the shift position is changed to R and the camera screen is being displayed, continues to display the guide lines.


·

U0100

·

U0126

·

U0129

·

U0140


(Radio and display receiver assembly [EMVN ECU])
Destination Determination
(Determines the destination based on the destination symbol and destination package information and selects the display settings such as the display language and time zone.)
Radio and display receiver assembly (EMVN ECU) Main body ECU (multiplex network body ECU) The destination is determined according to the last received value and the system is operated accordingly (if there is no last received value, the system operates using the default value). The time zone and language selection screens do not match the destination. (Radio and display receiver assembly [EMVN ECU])
Navigation Coordinated Control (AT/CVT)
(Predicts the road conditions based on the curve and inclination information and appropriately shifts gears according to conditions set by the driver, etc.)
·

ECM

·

Radio and display receiver assembly (EMVN ECU)


-
When a transmission error or a continuous bus off condition is detected:
·

AT/CVT coordinated control based on the curve information from the radio and display receiver assembly (EMVN ECU) is not performed.

·

If a connection confirmation response is not received, the ECM attempts to check the connection every 60 seconds.


When there is a reception stop:
·

AT/CVT coordinated control related information (curve information, etc.) is sent as the initial value.


Menu settings for navigation coordinated control are cleared.
·

U0073

·

U0100


(Radio and display receiver assembly [EMVN ECU])
Navigation Coordinated Control (Suspension)
(Learns bump information and locations, etc. based on requests from the suspension control ECU. When approaching a memorized location, notifies the system of bump information and performs suspension control.)
Radio and display receiver assembly (EMVN ECU) Suspension control ECU Bump learning processing is prohibited. Bump data during learning is discarded. However, bump data learned so far is maintained, and bump notification processing is performed based on that information. Menu settings for suspension coordinated control are cleared.
·

U0073

·

U0132


(Radio and display receiver assembly [EMVN ECU])
Navigation Coordinated Control (AFS)
(Controls AFS based on road information received by the radio and display receiver assembly (EMVN ECU) in advance.)
No. 1 headlight ECU sub-assembly LH Radio and display receiver assembly (EMVN ECU) - - U0073
(Radio and display receiver assembly [EMVN ECU])
Vehicle Customize Function
(Changes the behavior and control parameters of various functions [illumination lighting time, etc.] according to the user operation via the screen.)
Radio and display receiver assembly (EMVN ECU)
·

ECM

·

Skid control ECU

·

Main body ECU (multiplex network body ECU)

·

Certification ECU (smart key ECU assembly)

·

Front power seat switch (power seat control ECU)

·

Multiplex tilt and telescopic ECU

·

Air conditioning amplifier assembly


·

When an application that uses Phase 4 remote communication is performed (customize or remote diagnosis), the information is processed regardless of whether the main body ECU (multiplex network body ECU) has permitted or prohibited remote communication.

·

3 retries are performed (including the first time).


The related customization items are not displayed. Or the settings cannot be saved. U0073
(Radio and display receiver assembly [EMVN ECU])
Smart Camera Function
(Superimposes the estimated course lines of the vehicle, vehicle width extension lines and distance guide lines over the color rear camera image on the display when the vehicle is driven in reverse.)
Radio and display receiver assembly (EMVN ECU) ECM Does not change to the camera screen. - -
Meter-linked Function
(Changes the display based on the customization information set on the meter. Outputs the customization information set in the system.)
Radio and display receiver assembly (EMVN ECU) Combination meter assembly The previous value is maintained. - -
NOx Reduction
(Controls urea injected into the catalyst to reduce NOx in exhaust gas.)
ECM -
·

Urea addition valve forced operation is stopped.

-

Estimation of the remaining amount of urea stops (the previous estimated remaining amount value is maintained).

-

Tank/line/pump/heater stops.

-

Pump stops, then urea addition stops.


·

The system activation request is stopped.


MIL (Check malfunction indicator lamp) illuminates. -
Stop and Start System
(Stops the engine when the vehicle is stopped.)
Engine stop and start ECU
·

Air conditioning amplifier assembly

·

Skid control ECU

·

ECM

·

Steering sensor

·

Airbag sensor assembly

·

Main body ECU (multiplex network body ECU)

·

4 wheel drive control ECU (4WD control ECU)

·

Suspension control ECU


·

During Eco-run: It is restarted.

·

Not during Eco-run: Eco-run is prohibited.


ECO RUN CANCEL blinks.
·

U010087

·

U011487

·

U012687

·

U012987

·

U013287

·

U014087

·

U015187

·

U016487


(Engine stop and start ECU)