ENGINE CONTROL SYSTEM
| *A | w/ EGR Cooler | - | - |
| *1 | ECM | *2 | Pre-stroke Control Valve |
| *3 | Fuel Supply Pump Assembly | *4 | Common Rail Assembly |
| *5 | Pressure Discharge Valve | *6 | Glow Plug Controller |
| *7 | Intercooler | *8 | Intake Air Temperature Sensor (Turbo) |
| *9 | NO.1 EGR Cooler | *10 | Vacuum Switching Valve Assembly (for EGR Bypass Valve) |
| *11 | Mass Air Flow Meter Sub-assembly | *12 | Intake Air Temperature Sensor (Built Into Mass Air Flow Meter Sub-assembly) |
| *13 | Injector Assembly | *14 | Camshaft Position Sensor |
| *15 | Glow Plug Assembly | *16 | Electric EGR Control Valve Assembly |
| *17 | Nozzle Vane Position Sensor | *18 | Variable Vane DC Motor |
| *19 | Crankshaft Position Sensor | *20 | Engine Coolant Temperature Sensor |
| *21 | Manifold Absolute Pressure Sensor | *22 | Diesel Throttle Body Assembly |
| *23 | Oil Pressure Switching Valve Assembly | *24 | Oil Pressure Sender Gauge Assembly |
| *25 | Atmospheric Pressure Sensor | *26 | Accelerator Pedal Position Sensor |
| *A | w/ EGR System | - | - |
| *1 | ECM | *2 | Pre-stroke Control Valve |
| *3 | Fuel Supply Pump Assembly | *4 | Common Rail Assembly |
| *5 | Pressure Discharge Valve | *6 | Glow Plug Controller |
| *7 | Intercooler | *8 | Intake Air Temperature Sensor (Turbo) |
| *9 | Mass Air Flow Meter Sub-assembly | *10 | Intake Air Temperature Sensor (Built Into Mass Air Flow Meter) |
| *11 | Injector Assembly | *12 | Camshaft Position Sensor |
| *13 | Glow Plug Assembly | *14 | Electric EGR Control Valve Assembly |
| *15 | Nozzle Vane Position Sensor | *16 | Variable Vane DC Motor |
| *17 | Crankshaft Position Sensor | *18 | Engine Coolant Temperature Sensor |
| *19 | Manifold Absolute Pressure Sensor | *20 | Diesel Throttle Body Assembly |
| *21 | Atmospheric Pressure Sensor | *22 | Accelerator Pedal Position Sensor |
| *A | w/o EGR System | - | - |
| *1 | ECM | *2 | Pre-stroke Control Valve |
| *3 | Fuel Supply Pump Assembly | *4 | Common Rail Assembly |
| *5 | Pressure Discharge Valve | *6 | Glow Plug Controller |
| *7 | Intercooler | *8 | Intake Air Temperature Sensor (Turbo) |
| *9 | Mass Air Flow Meter Sub-assembly | *10 | Intake Air Temperature Sensor (Built Into Mass Air Flow Meter) |
| *11 | Injector Assembly | *12 | Camshaft Position Sensor |
| *13 | Glow Plug Assembly | *14 | Nozzle Vane Position Sensor |
| *15 | Variable Vane DC Motor | *16 | Crankshaft Position Sensor |
| *17 | Engine Coolant Temperature Sensor | *18 | Manifold Absolute Pressure Sensor |
| *19 | Diesel Throttle Body Assembly | *20 | Atmospheric Pressure Sensor |
| *21 | Accelerator Pedal Position Sensor | - | - |
i-ART SYSTEM
In the i-ART (Intelligent Accuracy Refinement Technology) System, i-ART injectors, which are injectors that have built-in pressure sensors, are used.
By incorporating a pressure sensor into the injector, any changes in the internal pressure of the injectors can be confirmed at a point close to where fuel is injected.
The i-ART injector directly detects its internal fuel pressure and fuel temperature.
The ECM receives the pressure waveform signal from the pressure sensor and detects the fuel injection volume to perform so that the fuel injection volume matches the target.
Due to this system, the fuel injection precision even in the smallest amount has been improved and precise control of multilevel injection has been made possible. In turn, combustion is more stable and the noise made during combustion has reduced.
The i-ART injectors automatically perform learning when they are replaced. Therefore, injector compensation code registration and pilot quantity learning is not necessary. Learning is performed while the engine is running.
| *1 | Nozzle | *2 | Two-Way Valve |
| *3 | Low Suck Volume Nozzle | *4 | Nozzle Needle |
| *5 | ·
Fuel Pressure Sensor ·
Fuel Temperature Sensor |
- | - |
| *a | Injector Assembly Cross Section Diagram | - | - |
COMMON RAIL SYSTEM DESCRIPTION
Common rail system:
The common rail system uses high-pressure fuel for improved fuel economy. This system also provides robust engine power while suppressing engine vibration and noise.
This system stores fuel in the common rail, which has been pressurized and supplied by the fuel supply pump assembly. By storing fuel at high-pressure, the common rail system can provide fuel at stable fuel injection pressures, regardless of engine speed or engine load.
The ECM provides an electric current to the solenoid valve in each injector assembly to regulate the fuel injection timing and volume. The ECM also monitors the internal fuel pressure of the common rail using the fuel pressure sensor built into each injector. The ECM causes the fuel supply pump assembly to supply the fuel necessary to obtain the target fuel pressure.
In addition, this system uses a solenoid valve inside each injector assembly to open and close the fuel passages. Therefore, both fuel injection time and fuel injection volume can be precisely regulated by the ECM.
| *1 | Common Rail Assembly | *2 | Pressure Discharge Valve |
| *3 | ECM | *4 | Crankshaft Position Sensor |
| *5 | Camshaft Position Sensor | *6 | Injector Assembly |
| *7 | Pre-stroke Control Valve | *8 | Fuel Supply Pump Assembly |
| *9 | Pressurized Fuel Filter | *10 | Fuel Filter Element Assembly |
| *11 | Fuel Tank Assembly | - | - |
|
High Pressure Fuel |
|
Return Fuel |
|
Suction Fuel |
|
Feed Pressure Fuel |
If there is a problem with a fuel return pipe, as bleeding air from the fuel system may not be able to be performed properly in certain instances, such as after replacing an injector assembly, etc., the engine startability may deteriorate.
Common rail system components:
| Component | Description |
|---|---|
| Common rail assembly | Stores high-pressure fuel produced by supply pump |
| Fuel supply pump assembly | ·
Operated by crankshaft via timing chain ·
Supplies high-pressure fuel to common rail assembly |
| Injector assembly | Injects fuel to combustion chamber based on signals from ECM |
| Fuel pressure sensor (Built into injector assembly) | Monitors internal fuel pressure of injector assembly and sends signals to ECM |
| Pressure discharge valve | Based on signals from ECM, opens valve when sudden deceleration occurs, or when ignition switch is off to prevent fuel pressure from becoming too high |
| Pre-stroke control valve | Based on signals from ECM, adjusts fuel volume supplied to common rail and regulates internal fuel pressure |
Diagnostic trouble code (DTC) table for the common rail system:
This table indicates typical DTC combinations for each malfunction occurrence.
| Trouble Area | Malfunction | DTC No. |
|---|---|---|
| Injector assembly | Open or short in injector circuit | P009300*, P020112, P020114, P020212, P020214, P020312, P020314, P020412, P020414, P029D00, P02A100, P02A500, P02A900, P062D96 |
| Stuck open | P009300, P029D00, P02A100, P02A500, P02A900 | |
| Stuck closed | P030100, P030200, P030300, P030400 | |
| Communication malfunction | P167A87, P167B87, P167C87, P167D87 | |
| Internal malfunction | P168A00, P168A44, P168A46, P168B00, P168B44, P168B46, P168C00, P168C44, P168C46, P168D00, P168D44, P168D46, | |
| Fuel pressure sensor (Built into injector assembly) | Open or short in fuel pressure sensor circuit | P13A011, P13A015, P13A511, P13A515, P13AA11, P13AA15, P13B011, P13B015, P13E011, P13E015, P13E511, P13E515 |
| Characteristic abnormality of the fuel pressure sensor | P13A02A, P13A52A, P13AA2A, P13B02A | |
| Fuel temperature sensor (Built into injector assembly) | Characteristic abnormality of the fuel temperature sensor | P13C013, P13C513, P13CA13, P13D013 |
| Pressure discharge valve | Open or short in pressure discharge valve circuit | P008800*, P009300*, P122900*, P127112, P127114 |
| Stuck open | P009300 | |
| Stuck closed | P008800*, P127273 | |
| Pre-stroke control valve | Open or short in pre-stroke control valve circuit | P008800*, P062712, P062714, P122900 |
| Stuck open | P008800*, P122900 | |
| Common rail system (Fuel system) | Fuel leaks in high-pressure area | P009300 |
*: There may be no DTC output depending on the condition of the malfunction.
Diagnostic trouble code description for the common rail system:
| DTC No. | Description |
|---|---|
| P008800 | Internal fuel pressure too high (275000 kPa [2804 kgf/cm2, 39875 psi] or more) |
| P009300 | Fuel leaks in high-pressure areas |
| P020112 | Short in No. 1 injector circuit (High output) |
| P020114 | Open in No. 1 injector circuit (Low output) |
| P020212 | Short in No. 2 injector circuit (High output) |
| P020214 | Open in No. 2 injector circuit (Low output) |
| P020312 | Short in No. 3 injector circuit (High output) |
| P020314 | Open in No. 3 injector circuit (Low output) |
| P020412 | Short in No. 4 injector circuit (High output) |
| P020414 | Open in No. 4 injector circuit (Low output) |
| P029D00 | Cylinder 1 - Injector Leaking |
| P02A100 | Cylinder 2 - Injector Leaking |
| P02A500 | Cylinder 3 - Injector Leaking |
| P02A900 | Cylinder 4 - Injector Leaking |
| P030100 | Cylinder 1 misfire detected |
| P030200 | Cylinder 2 misfire detected |
| P030300 | Cylinder 3 misfire detected |
| P030400 | Cylinder 4 misfire detected |
| P062712 | Short in pre-stroke control valve circuit (High output) |
| P062714 | Open in pre-stroke control valve circuit (Low output) |
| P062D96 | ECM internal error |
| P122900 | Fuel over-feed |
| P127112 | Short in pressure discharge valve circuit (High output) |
| P127114 | Open in pressure discharge valve circuit (Low output) |
| P127273 | Pressure discharge valve stuck close |
| P13A011 | Open or short in No. 1 injector assembly (fuel pressure sensor) circuit (output voltage is too low) (Sub CPU) |
| P13A015 | Open or short in No. 1 injector assembly (fuel pressure sensor) circuit (output voltage is too high) (Sub CPU) |
| P13A511 | Open or short in No. 2 injector assembly (fuel pressure sensor) circuit (output voltage is too low) (Sub CPU) |
| P13A515 | Open or short in No. 2 injector assembly (fuel pressure sensor) circuit (output voltage is too high) (Sub CPU) |
| P13AA11 | Open or short in No. 3 injector assembly (fuel pressure sensor) circuit (output voltage is too low) (Sub CPU) |
| P13AA15 | Open or short in No. 3 injector assembly (fuel pressure sensor) circuit (output voltage is too high) (Sub CPU) |
| P13B011 | Open or short in No. 4 injector assembly (fuel pressure sensor) circuit (output voltage is too low) (Sub CPU) |
| P13B015 | Open or short in No. 4 injector assembly (fuel pressure sensor) circuit (output voltage is too high) (Sub CPU) |
| P13E011 | Open or short in No. 1 injector assembly (fuel pressure sensor) circuit (output voltage is too low) (Main CPU) |
| P13E015 | Open or short in No. 1 injector assembly (fuel pressure sensor) circuit (output voltage is too high) (Main CPU) |
| P13E511 | Open or short in No. 4 injector assembly (fuel pressure sensor) circuit (output voltage is too low) (Main CPU) |
| P13E515 | Open or short in No. 4 injector assembly (fuel pressure sensor) circuit (output voltage is too high) (Main CPU) |
| P13A02A | No. 1 injector assembly (fuel pressure sensor) circuit range/performance |
| P13A52A | No. 2 injector assembly (fuel pressure sensor) circuit range/performance |
| P13AA2A | No. 3 injector assembly (fuel pressure sensor) circuit range/performance |
| P13B02A | No. 4 injector assembly (fuel pressure sensor) circuit range/performance |
| P13C013 | No. 1 injector assembly (fuel temperature sensor) circuit range/performance |
| P13C513 | No. 2 injector assembly (fuel temperature sensor) circuit range/performance |
| P13CA13 | No. 3 injector assembly (fuel temperature sensor) circuit range/performance |
| P13D013 | No. 4 injector assembly (fuel temperature sensor) circuit range/performance |
| P167A87 | No. 1 injector assembly communication malfunction |
| P167B87 | No. 2 injector assembly communication malfunction |
| P167C87 | No. 3 injector assembly communication malfunction |
| P167D87 | No. 4 injector assembly communication malfunction |
| P168A00 | No. 1 injector assembly internal malfunction |
| P168A44 | No. 1 injector assembly internal malfunction |
| P168A46 | No. 1 injector assembly internal malfunction |
| P168B00 | No. 2 injector assembly internal malfunction |
| P168B44 | No. 2 injector assembly internal malfunction |
| P168B46 | No. 2 injector assembly internal malfunction |
| P168C00 | No. 3 injector assembly internal malfunction |
| P168C44 | No. 3 injector assembly internal malfunction |
| P168C46 | No. 3 injector assembly internal malfunction |
| P168D00 | No. 4 injector assembly internal malfunction |
| P168D44 | No. 4 injector assembly internal malfunction |
| P168D46 | No. 4 injector assembly internal malfunction |
FUEL SUPPLY PUMP OPERATION SYSTEM DESCRIPTION
When the cam rotates the roller is pushed up, and in turn the plunger is pushed upward as well. When the plunger is not pushed up by the cam, it is pushed back down by the spring.
| *1 | Pre-stroke Control Valve | *2 | Plunger |
| *3 | Spring | *4 | Shoe |
| *5 | Roller | *6 | Double Cam |
The ECM controls the timing of the pre-stroke control valve opening to regulate the fuel quantity. Consequently, the fuel pressure in the common rail is controlled to the target injection pressure.
The longer the pre-stroke control valve remains open, the quantity of pressure-fed strokes will decrease, as well as the fuel discharge quantity.
Pumping will start when the fuel pressure has become higher than the common rail pressure.
| *a | Return Fuel | - | - |
The less time the pre-stroke control valve remains open, the quantity of pressure-fed strokes will increase, as well as the fuel discharge quantity.
Pumping will start when the fuel pressure has become higher than the common rail pressure.