Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0442647 ECD SYSTEM(w/ DPF) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P06DA12  Engine Oil Pressure Control Circuit Short to Battery  P06DA14  Engine Oil Pressure Control Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC P052477.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P052477

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P06DA12 Engine Oil Pressure Control Circuit Short to Battery While the oil pressure switching valve assembly is operating, the ECM detects high voltage for 5 seconds or more.
(1 trip detection logic)
·

Short in oil pressure switching valve assembly circuit

·

Oil pressure switching valve assembly

·

ECM


Does not come on DTC stored SAE Code: P06DC
P06DA14 Engine Oil Pressure Control Circuit Short to Ground or Open While the oil pressure switching valve assembly is not operating, the ECM detects low voltage for 5 seconds or more.
(1 trip detection logic)
·

Open or short in oil pressure switching valve assembly circuit

·

Oil pressure switching valve assembly

·

ECM


Does not come on DTC stored SAE Code: P06DB

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P06DA12 5 seconds or more after engine is started
P06DA14 Engine switch on (IG) for 5 seconds or more

WIRING DIAGRAM

A474994E15
2.698,1.135 5.448,1.333 2.75,0.198 10 false Oil Pressure Switching Valve Assembly 2.698,0.99 3.313,1.188 0.615,0.198 10 false C130 1.854,0.802 3.229,1 1.375,0.198 10 false EFI NO. 2 1.854,0.521 2.01,0.719 0.156,0.198 10 false 1 2.302,0.51 2.458,0.708 0.156,0.198 10 false 2 6.302,0.667 6.917,0.865 0.615,0.198 10 false EOPV 5.854,0.646 6.469,0.844 0.615,0.198 10 false C150 3.094,0.51 3.25,0.708 0.156,0.198 10 false 2 4.531,0.51 4.688,0.708 0.156,0.198 10 false 1 5.917,0.458 6.156,0.656 0.24,0.198 10 false 13 4.281,2.813 4.896,3.01 0.615,0.198 10 false 1W 4.354,2.646 4.51,2.844 0.156,0.198 10 false 3 2.469,2.708 2.625,2.906 0.156,0.198 10 false 2 2.031,2.698 2.188,2.896 0.156,0.198 10 false 1 2.938,3.542 4.313,3.74 1.375,0.198 10 false EFI MAIN NO. 2 1.813,4.146 3.188,4.344 1.375,0.198 10 false EFI MAIN NO. 1 1.792,2.958 3.167,3.156 1.375,0.198 10 false EFI MAIN NO. 2 2.99,4.76 4.365,4.958 1.375,0.198 10 false EFI MAIN NO. 1 4.281,3.219 4.896,3.417 0.615,0.198 10 false 1W 4.354,3.042 4.51,3.24 0.156,0.198 10 false 2 4.313,3.979 4.927,4.177 0.615,0.198 10 false 1V 4.313,4.406 4.927,4.604 0.615,0.198 10 false 1V 5.844,4.396 6.458,4.594 0.615,0.198 10 false G184 5.938,4.229 6.208,4.427 0.271,0.198 10 false 14 1.323,2.813 1.938,3.01 0.615,0.198 10 false 1S 1.292,3.219 1.906,3.417 0.615,0.198 10 false 1W 4.365,3.781 4.521,3.979 0.156,0.198 10 false 6 4.354,4.24 4.51,4.438 0.156,0.198 10 false 7 4.948,3.635 6.323,3.833 1.375,0.198 10 false EFI MAIN NO. 3 1.365,2.635 1.979,2.833 0.615,0.198 10 false 1 1.365,3.052 1.521,3.25 0.156,0.198 10 false 4 6.479,5.292 7.01,5.604 0.531,0.313 10 false ECM 0.417,4.063 1.792,4.26 1.375,0.198 10 false 70A FL 0.594,5.719 1.969,5.917 1.375,0.198 10 false Battry 2.104,5.24 3.896,5.5 1.792,0.26 10 false No. 1 Integration Relay 6.354,4.271 6.969,4.469 0.615,0.198 10 false MREL

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT OIL PRESSURE SWITCHING VALVE ASSEMBLY
a.

Inspect the oil pressure switching valve assembly.

Click hereEngine / Hybrid System>1GD-FTV (LUBRICATION)>OIL PRESSURE SWITCHING VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK OIL PRESSURE SWITCHING VALVE ASSEMBLY (POWER SOURCE CIRCUIT)

NG

7.REPLACE OIL PRESSURE SWITCHING VALVE ASSEMBLY
2.CHECK OIL PRESSURE SWITCHING VALVE ASSEMBLY (POWER SOURCE CIRCUIT)
a.

Disconnect the oil pressure switching valve assembly connector.


b.
A348992C42
1.469,1.042 1.917,1.365 0.448,0.323 0.177,0.125 0.49,0.323 0.313,0.198 10 false *a 1.542,1.125 1.906,1.344 0.365,0.219 10 false C130
*a Front view of wire harness connector
(to Oil Pressure Switching Valve Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C130-2 - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SWITCHING VALVE ASSEMBLY - ECM)

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SWITCHING VALVE ASSEMBLY - ECM)
a.

Disconnect the oil pressure switching valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C130-1 - C150-13 (EOPV) Always Below 1 Ω
C130-1 or C150-13 (EOPV) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.

HINT:

If the voltage at the oil pressure switching valve assembly connector is not 11 to 14 V, repair or replace the harness and connector between the oil pressure switching valve assembly and No. 1 integration relay.



Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.


c.

Turn the engine switch on (IG) for 5 seconds or more.


d.

Start the engine and wait for 5 seconds or more.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.


f.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.REPLACE OIL PRESSURE SWITCHING VALVE ASSEMBLY
a.

Replace the oil pressure switching valve assembly.

Click hereEngine / Hybrid System>1GD-FTV (LUBRICATION)>OIL PRESSURE SWITCHING VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED