Home › Engine / Hybrid System › 1GD-FTV (FUEL) › FUEL TANK (for 3 Door) › from 2020.08
RM27T0E _51 Engine / Hybrid System _053670 1GD-FTV FUEL _0260581 FUEL TANK(for 3 Door) A

1GD-FTV FUEL  FUEL TANK(for 3 Door)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the fuel tank sub-assembly removal/installation are shown below.

Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Correction of steering angle neutral point Multi-terrain monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane departure alert system Drive the vehicle straight ahead at 40 km/h (25 mph) or more for 10 seconds or more. (Click here)
Pre-collision system
Lighting system (EXT) (for LED Headlight)
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Vehicle stability control system (for Hydraulic brake booster) Drive the vehicle straight ahead at 40 km/h (25 mph) or more for at least 10 seconds. (Click here)



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 58325E 4.REMOVE REAR FLOOR SERVICE HOLE COVER

HINT:

Fold back the floor mat so that the rear floor service hole cover can be removed.


a.
A220855

Remove the 3 screws and rear floor service hole cover.


b.
A220856

Disconnect the fuel sender gauge connector and fuel tank ground connector.


Hide 77606 5.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.
A220857

Remove the 5 bolts and No. 1 fuel tank protector sub-assembly.


Hide 6.DRAIN FUEL

a.
A220858

Remove the fuel tank drain plug and gasket and drain the fuel.


b.

Install a new gasket and the fuel tank drain plug.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 7.DISCONNECT FUEL HOSE

a.
A220859

Slide the 2 clamps and disconnect the 2 fuel hoses from the fuel tank vent tube sub-assembly.


Hide 77213B 8.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A220860

Loosen the clamp and fuel tank to filler pipe hose from the filler pipe.


Hide 77269A 9.DISCONNECT FUEL TANK BREATHER HOSE

a.
A223278

Loosen the clamp and disconnect the fuel tank breather hose from the filler pipe.


Hide 77100U 10.REMOVE FUEL TANK SUB-ASSEMBLY

a.

Set a transmission jack underneath the fuel tank sub-assembly.


b.
A220861

Remove the 2 bolts, 2 clips and 2 pins and disconnect the 2 fuel tank bands.


c.

Remove the fuel tank sub-assembly.


Hide 77298C 11.REMOVE NO. 4 FUEL TUBE CLAMP

a.
A220862

Detach the clamp and remove the No. 4 fuel tube clamp from the fuel tank check valve.


Hide 77701T 12.REMOVE FUEL TANK CHECK VALVE

a.
A220863

Disconnect the hose and remove the fuel tank check valve.


Hide 77017D 13.REMOVE FUEL TANK VENT TUBE SUB-ASSEMBLY

a.
A220865

Remove the 7 screws, detach the 2 clamps and remove the fuel tank vent tube sub-assembly.


b.

Remove the gasket from the fuel tank vent tube sub-assembly.


Hide 77026B 14.REMOVE NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A220866

Remove the 4 screws and No. 1 fuel evaporation tube sub-assembly.


b.

Remove the gasket from the No. 1 fuel evaporation tube sub-assembly.


Hide 77380 15.REMOVE FUEL CUT OFF VALVE ASSEMBLY

a.

Remove the fuel cut off valve assembly from the fuel tank sub-assembly.


Hide 83320 16.REMOVE FUEL SENDER GAUGE ASSEMBLY

a.
A220867

Remove the 5 screws and fuel sender gauge assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



b.

Remove the gasket from the fuel sender gauge assembly.


Hide 77213B 17.REMOVE FUEL TANK TO FILLER PIPE HOSE

a.
A220868

Loosen the clamp and remove the fuel tank to filler pipe hose from the fuel tank sub-assembly.


Hide 77269A 18.REMOVE FUEL TANK BREATHER HOSE

a.
A223279

Loosen the clamp and remove the fuel tank breather hose from the fuel tank sub-assembly.


Hide 77011 19.REMOVE FUEL TANK FILLER PIPE LOWER SUB-ASSEMBLY

a.
A223091

Remove the 8 screws and fuel tank filler pipe lower sub-assembly.


b.

Remove the gasket from the fuel tank filler pipe lower sub-assembly.


Hide 77295C 20.REMOVE FUEL TUBE GROMMET

a.
A220864

Detach the clamp and remove the fuel tube grommet.


Hide 77651A 21.REMOVE NO. 1 FUEL TANK CUSHION

a.
A223092

Remove the 2 No. 1 fuel tank cushions from the fuel tank sub-assembly.