Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2020.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261011 BLIND SPOT MONITOR SYSTEM U

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Data List.


e.

Read the Data List according to the display on the GTS.

Blind Spot Monitor Master
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Main Switch Blind spot monitor system / OFF or ON ON: Blind spot monitor system on
OFF: Blind spot monitor system off
-
RCTA Switch Status State of the RCTA function / OFF or ON OFF: RCTA function off
ON: RCTA function on
-
Warning Indicator Turning on (Master) State of the outer rear view mirror indicator LH turning on / OFF or ON

OFF: Any state except "ON" state

ON: Either of the following state

-

During initial check

-

Blind spot monitor system on, vehicle detected on left hand side and turn signal switch not operated



-
Warning Indicator Flashing (Master) State of the outer rear view mirror indicator LH flashing / OFF or ON OFF: Any state except "ON" state
ON: Blind spot monitor system on, vehicle detected on left hand side and left side of turn signal switch on
-
Main Switch Indicator Status State of the blind spot monitor indicator on the blind spot monitor main switch assembly (multi-function switch) / OFF or ON OFF: Indicator not illuminated
ON: Indicator illuminated
-
Warning Indicator Input Circuit Voltage Outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V Not illuminated: Below 1 V
Illuminated: 2.5 to 7.5 V
-
Warning Indicator Input Circuit Current Outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA Not illuminated: 0 mA
Illuminated: 5 to 100 mA
-
Turn Switch State State of the headlight dimmer switch assembly (turn signal light switch) / Left ON, Right ON or OFF Left ON: Left side of turn signal light switch on
Right ON: Right side of turn signal light switch on
OFF: Turn signal light switch off
-
Reverse (Only for AT/CVT) State of the shift position R signal / OFF or ON ON: Shift lever in R
OFF: Shift lever in any position except R
-
Vehicle Speed Vehicle speed signal / -328 to 328 km/h (-204 to 204 mph) Vehicle stopped: 0 km/h (0 mph) -
Steering Angle Steering sensor / Min.: -3072°, Max.: 3070.5° Left turn: Increases
Right turn: Decreases
-
Power Supply Voltage Power supply voltage / Min.: 0 V, Max.: 49.951 V 11 to 14 V -
Indicator Light Control State Outer rear view mirror indicator dimming state / Dim OFF or Dim ON Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed
-
HV/EV Flag Hybrid vehicle / OFF or ON OFF: Non-hybrid vehicle
ON: Hybrid vehicle
-
VGRS Flag VGRS installed / OFF or ON OFF: VGRS not installed
ON: VGRS installed
-
Beam Axis Inspection Completeness Flag Completion of beam axis inspection / Incompl or Compl Incompl: Inspection not completed
Compl: Inspection completed
Changes to Compl when Test Mode has been entered.
Destination Undefined Flag Destination determination / Unfixed or Fixed Unfixed: Sensor destination information not determined
Fixed: Sensor destination information determined according to CAN destination information
-
Angle Adjustment by Auto Alignment Angle adjusted using auto alignment / Min.: Under -180 deg, Max.: Over 180 deg Angle adjusted using auto alignment is displayed -
Setting of Warning Indicator Current (Dim OFF) Set current of the outer rear view mirror indicator when not dimmed / Min.: 0 mA, Max.: 100 mA 0 to 100 mA -
Setting of Warning Indicator Current (Dim ON) Set current of the outer rear view mirror indicator when dimmed / Min.: 0 mA, Max.: 100 mA 0 to 100 mA -
Mirror LED Duty Ratio (Blinking) Duty ratio of the outer rear view mirror indicator when blinking / Min.: 0%, Max.: 100% 50% -
Yaw Rate Sensor Yaw rate sensor / Min.: Under -124.928 deg/s, Max.: 124.684 deg/s Turning right: -124.928 to 0 deg/s
Turning left: 0 to 124.684 deg/s
-
Number of DTC Number of DTC / Min.: 0, Max.: 255 When system is normal: 0
When a malfunction is detected: More than 0
-

Blind Spot Monitor Slave
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Warning Indicator Turning on (Slave) State of the outer rear view mirror indicator RH turning on / OFF or ON OFF: Any state except "ON" state
ON: Either of the following state
·

During initial check

·

Blind spot monitor system on, vehicle detected on right hand side and turn signal switch not operated


-
Warning Indicator Flashing (Slave) State of the outer rear view mirror indicator RH flashing / OFF or ON OFF: Any state except "ON" state
ON: Blind spot monitor system on, vehicle detected on right hand side and right side of turn signal switch on
-
Buzzer Sound Status State of the RCTA buzzer (blind spot monitor buzzer) / OFF or ON OFF: Buzzer not sounding

ON: All of the following conditions are met:

-

Not during initial check

-

Vehicle detected in warning area of RCTA

-

Speed difference between driver's vehicle and target vehicle is 1.5 m/s or more

-

Shift lever in R

-

No DTC output



-
Warning Indicator Input Circuit Voltage Outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V Not illuminated: Below 1 V
Illuminated: 2.5 to 7.5 V
-
Warning Indicator Input Circuit Current Outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA Not illuminated: 0 mA
Illuminated: 5 to 100 mA
-
Buzzer Input Circuit Voltage RCTA buzzer (blind spot monitor buzzer) voltage / Min.: 0 V, Max.: 25.5 V Not sounding buzzer: 11 to 14 V
Sounding buzzer: Alternating between 0 to 14 V
-
Turn Switch State State of the headlight dimmer switch assembly (turn signal light switch) / Left ON, Right ON or OFF Left ON: Left side of turn signal light switch on
Right ON: Right side of turn signal light switch on
OFF: Turn signal light switch off
-
Reverse (Only for AT/CVT) State of the shift position R signal / OFF or ON ON: Shift lever in R
OFF: Shift lever in any position except R
-
Reverse (Only for MT) Not Supported / OFF or ON - -
Vehicle Speed Vehicle speed signal / -328 to 328 km/h (-204 to 204 mph) Vehicle stopped: 0 km/h (0 mph) -
Steering Angle Steering sensor / Min.: -3072°, Max.: 3070.5° Left turn: Increases
Right turn: Decreases
-
Power Supply Voltage Power supply voltage / Min.: 0 V, Max.: 49.951 V 11 to 14 V -
Indicator Light Control State Outer rear view mirror indicator dimming state / Dim OFF or Dim ON Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed
-
HV/EV Flag Hybrid vehicle / OFF or ON OFF: Non-hybrid vehicle
ON: Hybrid vehicle
-
VGRS Flag VGRS installed / OFF or ON OFF: VGRS not installed
ON: VGRS installed
-
Beam Axis Inspection Completeness Flag Completion of beam axis inspection / Incompl or Compl Incompl: Inspection not completed
Compl: Inspection completed
Changes to Compl when Test Mode has been entered.
Destination Undefined Flag Destination determination / Unfixed or Fixed Unfixed: Sensor destination information not determined
Fixed: Sensor destination information determined according to CAN destination information
-
Angle Adjustment by Auto Alignment Angle adjusted using auto alignment / Min.: Under -180 deg, Max.: Over 180 deg Angle adjusted using auto alignment is displayed -
Setting of Warning Indicator Current (Dim OFF) Set current of the outer rear view mirror indicator when not dimmed / Min.: 0 mA, Max.: 100 mA 0 to 100 mA -
Setting of Warning Indicator Current (Dim ON) Set current of the outer rear view mirror indicator when dimmed / Min.: 0 mA, Max.: 100 mA 0 to 100 mA -
Mirror LED Duty Ratio (Blinking) Duty ratio of the outer rear view mirror indicator when blinking / Min.: 0%, Max.: 100% 50% -
Buzzer Control Frequency Frequency of the RCTA buzzer (blind spot monitor buzzer) when sounding / Min.: 1000 Hz, Max.: 2400 Hz 2400 Hz -
Yaw Rate Sensor Yaw rate sensor / Min.: Under -124.928 deg/s, Max.: 124.684 deg/s Turning right: -124.928 to 0 deg/s
Turning left: 0 to 124.684 deg/s
-
BSM Buzzer Volume Adjust Volume of the RCTA buzzer (blind spot monitor buzzer) / Low, Medium or High Low: Buzzer volume less than that of medium
Medium: Default buzzer volume
High: Buzzer volume more than that of medium
-
Number of DTC Number of DTC / Min.: 0, Max.: 255 When system is normal: 0
When a malfunction is detected: More than 0
-