Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2020.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261011 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  U0232  Lost Communication with Blind Spot Monitor Slave Module  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH judges that there is a communication error with the blind spot monitor sensor RH.

DTC Code DTC Detection Condition Trouble Area
U0232 The blind spot monitor sensor LH cannot receive signals from the blind spot monitor sensor RH.
·

Open or short in CAN bus main wire or connector

·

Blind spot monitor sensor RH

·

Power source circuit of blind spot monitor sensor RH

·

Blind spot monitor sensor RH ground circuit

·

Blind spot monitor sensor LH



WIRING DIAGRAM

E382473E04
5.646,2.104 6.813,2.583 1.167,0.479 10 false Blind Spot Monitor Sensor LH 5.646,1.948 5.958,2.177 0.313,0.229 10 false R42 3.271,1.969 3.583,2.198 0.313,0.229 10 false R43 3.26,2.125 4.427,2.604 1.167,0.479 10 false Blind Spot Monitor Sensor RH 5.646,0.458 6.094,0.688 0.448,0.229 10 false CA2P 3.875,0.458 4.323,0.688 0.448,0.229 10 false CA2P 3.885,1.104 4.333,1.333 0.448,0.229 10 false CA2N 5.625,1.115 6.073,1.344 0.448,0.229 10 false CA2N 4.375,0.458 4.688,0.688 0.313,0.229 10 false 1 5.479,0.458 5.792,0.688 0.313,0.229 10 false 1 5.469,1.104 5.781,1.333 0.313,0.229 10 false 6 4.365,1.125 4.677,1.354 0.313,0.229 10 false 6 3.281,0.885 3.594,1.115 0.313,0.229 10 false BRB 2.156,1.063 3.167,1.313 1.01,0.25 10 false IG1 2.688,0.292 3,0.521 0.313,0.229 10 false *1 2.698,0.792 3.01,1.021 0.313,0.229 10 false *2 0.177,0.906 1.583,1.188 1.406,0.281 10 false from IG NO.1 Relay 0.167,0.292 1.5,0.719 1.333,0.427 10 false from Engine Stop and Start ECU 3.104,0.771 3.417,1 0.313,0.229 10 false 5 0.177,2.104 2.167,2.354 1.99,0.25 10 false *1: w/ Stop and Start System 0.177,2.396 2.167,2.646 1.99,0.25 10 false *2: w/o Stop and Start System 3.042,1.26 3.354,1.49 0.313,0.229 10 false 10 3.302,1.375 4,1.625 0.698,0.25 10 false BRGD

CAUTION / NOTICE / HINT

NOTICE:
·

When checking for DTCs, make sure that the blind spot monitor main switch (multi-function switch) is on.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the engine switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:
·

Operating the engine switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BODY GROUND)
a.
E375699C39
1.552,0.292 1.958,0.542 0.406,0.25 2.49,1.906 2.333,1.906 2.333,1.906 1.99,1.354 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 1.625,0.333 1.938,0.531 0.313,0.198 10 false R43 2.573,1.833 3.042,2.01 0.469,0.177 10 false BRGD
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


Disconnect the blind spot monitor sensor RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R43-10 (BRGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH POWER SOURCE)

NG

REPAIR OR REPLACE CAN LINE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH POWER SOURCE)
a.
E375699C40
1.5,0.271 1.948,0.563 0.448,0.292 1.979,1.167 2.49,0.531 2.49,0.531 2.688,0.531 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 1.573,0.323 1.885,0.521 0.313,0.198 10 false R43 2.802,0.458 3.208,0.646 0.406,0.188 10 false BRB
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


Disconnect the blind spot monitor sensor RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

*1: w/ Stop and Start System

*2: w/o Stop and Start System

R43-5 (BRB) - Body ground Emgine switch on (IG) 10.5 to 16 V*1
11 to 14 V*2
R43-5 (BRB) - Body ground Engine switch off Below 1 V



Result:
Result Proceed to
OK A
NG (w/o Stop and Start System) B
NG (w/ Stop and Start System) C



A

3.CHECK FOR OPEN OR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH)

B

REPAIR OR REPLACE CAN LINE OR CONNECTOR

C

3.CHECK FOR OPEN OR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH)
a.
E418117C11
1.479,1.677 1.948,1.969 0.469,0.292 1.427,0.219 1.823,0.51 0.396,0.292 0.75,0.781 0.938,0.781 0.938,0.781 1.375,1.052 true 0.75,1.49 0.938,1.49 0.938,1.49 1.365,1.229 true 1,2 1.167,2 1.167,2 1.646,2.365 true 2.25,2.708 2.438,3.135 2.438,3.135 2.552,3.135 true 0.24,1.896 0.552,2.052 0.313,0.156 10 false *b 0.177,0.198 0.49,0.354 0.313,0.156 10 false *a 1.542,1.75 1.969,1.969 0.427,0.219 10 false G317 1.5,0.271 1.813,0.469 0.313,0.198 10 false R42 0.333,0.708 0.948,0.906 0.615,0.198 10 false CA2P 0.344,1.406 0.958,1.604 0.615,0.198 10 false CA2N 2.667,3.052 3.281,3.25 0.615,0.198 10 false BAT 0.698,1.917 1.313,2.115 0.615,0.198 10 false CG
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)
*b Front view of wire harness connector
(DLC3)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R42-1 (CA2P) - R42-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
R42-1 (CA2P) - G317-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
R42-6 (CA2N) - G317-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
R42-1 (CA2P) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
R42-6 (CA2N) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

4.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH)
4.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH)
a.
E418117C12
1.479,1.677 1.948,1.969 0.469,0.292 1.427,0.219 1.823,0.51 0.396,0.292 0.75,0.781 0.938,0.781 0.938,0.781 1.375,1.052 true 0.75,1.49 0.938,1.49 0.938,1.49 1.365,1.229 true 1,2 1.167,2 1.167,2 1.646,2.365 true 2.25,2.708 2.438,3.135 2.438,3.135 2.552,3.135 true 0.24,1.896 0.552,2.052 0.313,0.156 10 false *b 0.177,0.198 0.49,0.354 0.313,0.156 10 false *a 1.563,1.74 2.073,2 0.51,0.26 10 false G317 1.51,0.271 1.823,0.469 0.313,0.198 10 false R43 0.333,0.708 0.948,0.906 0.615,0.198 10 false CA2P 0.344,1.406 0.958,1.604 0.615,0.198 10 false CA2N 2.667,3.052 3.281,3.25 0.615,0.198 10 false BAT 0.698,1.917 1.313,2.115 0.615,0.198 10 false CG
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)
*b Front view of wire harness connector
(DLC3)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the blind spot monitor sensor RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R43-1 (CA2P) - R43-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
R43-1 (CA2P) - G317-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
R43-6 (CA2N) - G317-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
R43-1 (CA2P) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
R43-6 (CA2N) - G317-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN LINE OR CONNECTOR