CHECK ENGINE SWITCH
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
|---|---|---|---|---|---|---|
| G206-6 (AGND) - Body ground | - | GR - Body ground | Transponder key amplifier ground | Always | Below 1 Ω | - |
| G206-7 (TXCT) - G206-6 (AGND) | Input | W - GR | Immobiliser communication input | Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed | Below 1 V | - |
| G206-8 (CODE) - G206-6 (AGND) | Output | V - GR | Immobiliser communication output | Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed | Below 1 V | - |
| G206-10 (VC5) - G206-6 (AGND) | Input | P - GR | Transponder key amplifier power supply | Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed | Below 1 V | - |
*1: for Automatic Transmission
*2: for Manual Transmission
Check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
|---|---|---|---|---|---|---|
| G206-7 (TXCT) - G206-6 (AGND) | Input | W - GR | Signal input from certification ECU (smart key ECU assembly)
(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves) |
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed | Pulse generation
(See waveform 1) |
·
BCC Malfunction ·
Abnormal Status ·
Different Encrypt Code ·
Different Serial Number ·
Frame Error ·
Response
|
| G206-8 (CODE) - G206-6 (AGND) | Output | V - GR | Signal output to certification ECU (smart key ECU assembly)
(Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly)) |
Engine switch off, engine switch pressed with key held near engine switch* | Pulse generation
(See waveform 2) |
|
| G206-10 (VC5) - G206-6 (AGND) | Input | P - GR | Transponder key amplifier power supply
(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into engine switch activated) |
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed | Pulse generation
(See waveform 3) |
*: Remove the transmitter battery before performing this inspection.
Using an oscilloscope, check the waveform.
The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
Waveform 1 (Reference)
| Item | Content |
|---|---|
| Tester Connection | G206-7 (TXCT) - G206-6 (AGND) |
| Tool Setting | 2 V/DIV., 20 ms./DIV. |
| Condition | Engine switch off, key not in cabin, within 30 seconds after engine switch pressed |
| *a | Waveform |
| *b | Waveform (detail) |
Waveform 2 (Reference)
| Item | Content |
|---|---|
| Tester Connection | G206-8 (CODE) - G206-6 (AGND) |
| Tool Setting | ·
Waveform 2 V/DIV., 20 ms./DIV. ·
Waveform (detail) 2 V/DIV., 100 μs./DIV. |
| Condition | Engine switch off, engine switch pressed with key held near engine switch* |
*: Remove the transmitter battery before performing this inspection.
Waveform 3 (Reference)
| Item | Content |
|---|---|
| Tester Connection | G206-10 (VC5) - G206-6 (AGND) |
| Tool Setting | 2 V/DIV., 200 ms./DIV. |
| Condition | Engine switch off, key not in cabin, within 30 seconds after engine switch pressed |
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Disconnect the G215 certification ECU (smart key ECU assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
|---|---|---|---|---|---|---|
| G215-10 (+B) - G215-11 (E) | Input | V - W-B | +B power supply | Always | 11 to 14 V | - |
| G215-11 (E) - Body ground | - | W-B - Body ground | Ground | Always | Below 1 Ω | - |
Reconnect the G215 certification ECU (smart key ECU assembly) connector.
Measure the voltage and resistance and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
|---|---|---|---|---|---|---|
| G215-14 (TXCT) - G215-12 (AGND) | Output | W - GR | Signal output to transponder key amplifier | Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed | Below 1 V | ·
BCC Malfunction ·
Abnormal Status ·
Different Encrypt Code ·
Different Serial Number ·
Frame Error ·
Response |
| G215-13 (CODE) - G215-12 (AGND) | Input | V - GR | Signal input from transponder key amplifier | Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed | Below 1 V | |
| G215-15 (VC5) - G215-12 (AGND) | Output | P - GR | Transponder key amplifier power supply | Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed | Below 1 V | |
| G215-12 (AGND) - Body ground | - | GR - Body ground | Transponder key amplifier ground | Always | Below 1 Ω | |
| G215-19 (IND) - G215-11 (E) | Output | G - W-B | Security indicator output | Engine switch off → on (IG) | Pulse generation → Below 2 V | - |
*1: for Automatic Transmission
*2: for Manual Transmission
Check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
|---|---|---|---|---|---|---|
| G215-14 (TXCT) - G215-12 (AGND) | Output | W - GR | Signal output to transponder key amplifier
(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves) |
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed | Pulse generation
(See waveform 1) |
·
BCC Malfunction ·
Abnormal Status ·
Different Encrypt Code ·
Different Serial Number ·
Frame Error ·
Response |
| G215-13 (CODE) - G215-12 (AGND) | Input | V - GR | Signal input from transponder key amplifier
(Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly)) |
Engine switch off, engine switch pressed with key held near engine switch* | Pulse generation
(See waveform 2) |
|
| G215-15 (VC5) - G215-12 (AGND) | Output | P - GR | Transponder key amplifier power supply
(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into engine switch activated) |
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed | Pulse generation
(See waveform 3) |
*: Remove the transmitter battery before performing this inspection.
Using an oscilloscope, check the waveform.
The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
Waveform 1 (Reference)
| Item | Content |
|---|---|
| Tester Connection | G215-14 (TXCT) - G215-12 (AGND) |
| Tool Setting | 2 V/DIV., 20 ms./DIV. |
| Condition | Engine switch off, key not in cabin, within 30 seconds after engine switch pressed |
| *a | Waveform |
| *b | Waveform (detail) |
Waveform 2 (Reference)
| Item | Content |
|---|---|
| Tester Connection | G215-13 (CODE) - G215-12 (AGND) |
| Tool Setting | ·
Waveform 2 V/DIV., 20 ms./DIV. ·
Waveform (detail) 2 V/DIV., 100 μs./DIV. |
| Condition | Engine switch off, engine switch pressed with key held near engine switch* |
*: Remove the transmitter battery before performing this inspection.
Waveform 3 (Reference)
| Item | Content |
|---|---|
| Tester Connection | G215-15 (VC5) - G215-12 (AGND) |
| Tool Setting | 2 V/DIV., 200 ms./DIV. |
| Condition | Engine switch off, key not in cabin, within 30 seconds after engine switch pressed |
CHECK ID CODE BOX (IMMOBILISER CODE ECU)
Disconnect the G207 ID code box (immobiliser code ECU) connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
|---|---|---|---|---|---|---|
| G207-1 (+B) - Body ground | Input | V - Body ground | +B power supply | Always | 11 to 14 V | B2789 |
| G207-5 (GND) - Body ground | - | W-B - Body ground | Ground | Always | Below 1 Ω | B2789 |
Reconnect the G207 ID code box (immobiliser code ECU) connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
|---|---|---|---|---|---|---|
| G207-3 (EFII) - G207-5 (GND) | Input | SB - W-B | EFI communication input
(Signal input from ECM to ID code box (immobiliser code ECU)) |
Engine switch off | 11 to 14 V | ·
B2799*1 ·
B279A*1 ·
B279986*2 ·
B279A12*2 ·
EFI Code Receive ·
Engine Start Request |
| G207-4 (EFIO) - G207-5 (GND) | Output | W - W-B | EFI communication output
(Signal output from ID code box (immobiliser code ECU) to ECM) |
Engine switch off | Below 1 V | |
| G207-3 (EFII) - G207-5 (GND) | Input | SB - W-B | EFI communication input
(Signal input from ECM to ID code box (immobiliser code ECU)) |
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected | Pulse generation
(See waveform 1) |
|
| G207-4 (EFIO) - G207-5 (GND) | Output | W - W-B | EFI communication output
(Signal output from ID code box (immobiliser code ECU) to ECM) |
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected | Pulse generation
(See waveform 2) |
*1: except 1GD-FTV
*2: for 1GD-FTV
Using an oscilloscope, check the waveform.
The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
Waveform 1 (Reference)
| *a | Approximately 160 ms | *b | Approximately 270 ms |
| Item | Content |
|---|---|
| Tester Connection | G207-3 (EFII) - G207-5 (GND) |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected |
Waveform 2 (Reference)
| *a | Approximately 160 ms | *b | Approximately 270 ms |
| Item | Content |
|---|---|
| Tester Connection | G207-4 (EFIO) - G207-5 (GND) |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected |
CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
Measure the voltage and resistance and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
|---|---|---|---|---|---|---|
| G35-1 (GND) - Body ground | - | W-B - Body ground | Ground | Always | Below 1 Ω | - |
| G35-3 (IGE) - G35-1 (GND) | Input | W - W-B | Steering lock motor operation permission signal (motor operation permission signal supplied by certification ECU (smart key ECU assembly)) | Steering lock motor operates when both conditions met, and then door opened:
·
Shift lever in P*1 ·
Electrical key transmitter sub-assembly carried, engine switch turned on (IG), steering unlocked, and then engine switch turned off |
Pulse generation
(See waveform 1) |
·
Power Supply Short ·
Unlock Request Receive ·
Lock Request Receive |
| G35-4 (SLP1) - G35-1 (GND) | Output | SB - W-B | Steering lock bar position signal (signal output from steering unlock sensor) | Steering locked → unlocked*2 | 11 to 14 V → Below 1.5 V | Sensor Value |
| G35-6 (IG2) - G35-1 (GND) | Input | W - W-B | IG signal (IG2 power supply input for steering lock motor) | Engine switch off → on (IG) | Below 1 V → 11 to 14 V | B2788 |
| G35-7 (B) - Body ground | Input | G - Body ground | Constant power supply | Always | 11 to 14 V | B2788 |
*1: for Automatic Transmission
*2: The steering locks when any door is opened with the shift lever in P (for Automatic Transmission) and the engine switch off. The steering unlocks when the engine switch is turned on (ACC).
Using an oscilloscope, check the waveform.
The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| *a | Steering lock motor not operating |
| *b | Steering lock motor operating |
Waveform 1 (Reference)
| Item | Content |
|---|---|
| Tester Connection | G35-3 (IGE) - G35-1 (GND) |
| Tool Setting | 2 V/DIV., 200 ms./DIV. |
| Condition | Steering lock motor operates when both conditions met, and then door opened:
·
Shift lever in P* ·
Electrical key transmitter sub-assembly carried, engine switch turned on (IG), steering unlocked, and then engine switch turned off |
*: for Automatic Transmission
CHECK ECM (for 1GR-FE)
Measure the resistance, voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| C36-12 (E1) - Body ground | - | BR - Body ground | Ground | Always | Below 1 Ω | - |
| G56-8 (IMO) - C36-12 (E1)*1
G56-20 (IMO) - C36-12 (E1)*2 |
Output | SB - BR | Certification ECU (smart key ECU assembly) communication output | Engine switch off | 11 to 14 V | E/G Start Permission |
| Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal | Pulse generation
(See waveform 1) |
E/G Start Permission | ||||
| G56-10 (IMI) - C36-12 (E1)*1
G56-14 (IMI) - C36-12 (E1)*2 |
Input | W - BR | Certification ECU (smart key ECU assembly) communication input | Engine switch off | Below 1 V | E/G Start Permission |
| Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal | Pulse generation
(See waveform 2) |
E/G Start Permission |
*1: for Automatic Transmission
*2: for Manual Transmission
Using an oscilloscope, check the waveform.
The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
Waveform 1 (Reference)
| *a | Approximately 160 ms | *b | Approximately 270 ms |
| Tester Connection | G56-8 (IMO) - C36-12 (E1)*1
G56-20 (IMO) - C36-12 (E1)*2 |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal |
*1: for Automatic Transmission
*2: for Manual Transmission
Waveform 2 (Reference)
| *a | Approximately 160 ms | *b | Approximately 270 ms |
| Tester Connection | G56-10 (IMI) - C36-12 (E1)*1
G56-14 (IMI) - C36-12 (E1)*2 |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal |
*1: for Automatic Transmission
*2: for Manual Transmission
CHECK ECM (for 2TR-FE)
| *A | for Automatic Transmission | *B | for Manual Transmission |
Measure the resistance, voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| C153-3 (E1) - Body ground | - | BR - Body ground | Ground | Always | Below 1 Ω | - |
| G181-9 (IMO) - C153-3 (E1) | Output | SB - BR | Certification ECU (smart key ECU assembly) communication output | Engine switch off | 11 to 14 V | E/G Start Permission |
| Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal | Pulse generation
(See waveform 1) |
E/G Start Permission | ||||
| G181-10 (IMI) - C153-3 (E1) | Input | W - BR | Certification ECU (smart key ECU assembly) communication input | Engine switch off | Below 1 V | E/G Start Permission |
| Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal | Pulse generation
(See waveform 2) |
E/G Start Permission |
Using an oscilloscope, check the waveform.
The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
Waveform 1 (Reference)
| *a | Approximately 160 ms | *b | Approximately 270 ms |
| Tester Connection | G181-9 (IMO) - C153-3 (E1) |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal |
Waveform 2 (Reference)
| *a | Approximately 160 ms | *b | Approximately 270 ms |
| Tester Connection | G181-10 (IMI) - C153-3 (E1) |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal |
CHECK ECM (for 1GD-FTV)
Measure the resistance, voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
|---|---|---|---|---|---|---|
| G185-5 (E1) - Body ground | - | W-B - Body ground | Ground | Always | Below 1 Ω | - |
| G185-17 (IMO) - G185-5 (E1) | Output | SB - W-B | Certification ECU (smart key ECU assembly) communication output | Engine switch off | 11 to 14 V | - |
| Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected | Pulse generation
(See waveform 1) |
- | ||||
| G185-16 (IMI) - G185-5 (E1) | Input | W - W-B | Certification ECU (smart key ECU assembly) communication input | Engine switch off | Below 1 V | - |
| Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected | Pulse generation
(See waveform 2) |
- |
Using an oscilloscope, check the waveform.
The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
Waveform 1 (Reference)
| *a | Approximately 160 ms | *b | Approximately 270 ms |
| Item | Content |
|---|---|
| Tester Connection | G185-17 (IMO) - G185-5 (E1) |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected |
Waveform 2 (Reference)
| *a | Approximately 160 ms | *b | Approximately 270 ms |
| Item | Content |
|---|---|
| Tester Connection | G185-16 (IMI) - G185-5 (E1) |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected |