Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) › from 2020.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261055 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  B2784  Antenna Coil Open / Short  


DESCRIPTION

When an open or short circuit is detected in the transponder key amplifier coil built into the engine switch, the certification ECU (smart key ECU assembly) stores this DTC. This DTC is also stored as a past DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2784 Antenna Coil Open / Short The transponder key amplifier coil built into the engine switch is open (see below) or shorted (determined by communication with certification ECU (smart key ECU assembly)) (1 trip detection logic*1).
·

Terminal AGND, VC5, TXCT or CODE circuit is open (includes disconnection of the engine switch).

·

The transponder key amplifier coil built into the engine switch is open.


·

Engine switch

·

Harness or connector

·

Certification ECU (smart key ECU assembly)


DTC output confirmation operation:

With the shift lever in P*2 and the key held near the engine switch, an engine start operation is performed by pressing and holding the engine switch when the key battery is depleted.



*1: Only output while a malfunction is present.

*2: for Automatic Transmission


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started when key battery is depleted by holding key near engine switch and pressing and holding engine switch with shift lever in P* -

*: for Automatic Transmission


Related Data List and Active Test
DTC No. Data List and Active Test
B2784 -

WIRING DIAGRAM

E305785E42
1.5,0.781 2.021,1.24 0.521,0.458 10 false VC5 1.917,0.677 2.438,1.135 0.521,0.458 10 false 10 1.479,1.292 2,1.75 0.521,0.458 10 false TXCT 1.396,1.708 1.917,2.167 0.521,0.458 10 false CODE 1.938,1.198 2.458,1.656 0.521,0.458 10 false 7 1.938,1.719 2.458,2.177 0.521,0.458 10 false 8 1.938,2.219 2.458,2.677 0.521,0.458 10 false 6 1.406,2.219 1.927,2.677 0.521,0.458 10 false AGND 0.219,3.052 0.656,3.24 0.438,0.188 10 false G206 0.219,3.208 1.771,3.479 1.552,0.271 10 false Engine Switch 4.99,0.677 5.51,1.135 0.521,0.458 10 false 15 5,1.198 5.521,1.656 0.521,0.458 10 false 14 5,1.719 5.521,2.177 0.521,0.458 10 false 13 5,2.229 5.521,2.688 0.521,0.458 10 false 12 6.219,0.292 6.74,0.75 0.521,0.458 10 false 5 V 5.115,3.021 5.635,3.229 0.521,0.208 10 false G215 5.146,3.198 6.677,3.667 1.531,0.469 10 false Certification ECU (Smart Key ECU Assembly) 5.26,0.688 5.781,1.146 0.521,0.458 10 false VC5 5.26,1.188 5.781,1.646 0.521,0.458 10 false TXCT 5.25,1.719 5.771,2.177 0.521,0.458 10 false CODE 5.25,2.229 5.771,2.688 0.521,0.458 10 false AGND 6.156,1.542 6.677,2 0.521,0.458 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



PROCEDURE

1.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Trouble Codes.



Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System)>DTC CHECK / CLEAR

HINT:

Before checking for DTCs, perform "DTC Output Confirmation Operation" procedure.



Result:
Result Proceed to
DTC B2784 is not output. A
DTC B2784 is output. B



A

B

3.CHECK ENGINE SWITCH
3.CHECK ENGINE SWITCH
a.

Using an oscilloscope, check the waveform.

B363541C46
1.448,0.948 1.885,1.167 0.438,0.219 1.344,2.896 1.635,2.896 1.635,2.896 1.635,2.156 true 2.198,2.896 1.875,2.896 1.875,2.896 1.875,2.156 true 0.74,1.083 1.052,1.24 0.313,0.156 10 false *a 3.385,0.281 3.698,0.438 0.313,0.156 10 false *b 3.406,2.052 3.719,2.208 0.313,0.156 10 false *c 6.49,1.333 7.031,1.563 0.542,0.229 10 false GND 6.49,3.115 7.031,3.344 0.542,0.229 10 false GND 2.26,2.813 2.802,3.042 0.542,0.229 10 false AGND 0.917,2.823 1.458,3.052 0.542,0.229 10 false CODE 1.479,0.969 2.021,1.198 0.542,0.229 10 false G206
*a Component with harness connected
(Engine Switch)
*b Waveform
*c Waveform (detail) - -


OK:
Tester Connection Condition Tool Setting Specified Condition
G206-8 (CODE) - G206-6 (AGND) Engine switch off, engine switch pressed with electrical key transmitter sub-assembly held near engine switch* 1 V/DIV., 20 ms./DIV. Pulse generation
(See waveform)
2 V/DIV., 100 μs./DIV. Pulse generation
(See waveform (detail))


HINT:

*: Remove the transmitter battery before performing this inspection.


OK:

The waveform is similar to that shown in the illustration



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG