Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) › from 2020.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261055 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  B279986  Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid  


DESCRIPTION

When there is a communication malfunction between the ECM and ID code box (immobiliser code ECU), or when the communication ID codes do not match, the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279986 Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid Either condition is met (1 trip detection logic*1):
·

A malfunction in the communication or communication lines between the ECM and ID code box (immobiliser code ECU).

·

A matching communication code cannot be verified during communication between the ECM and ID code box (immobiliser code ECU).


·

ID code box (immobiliser code ECU)

·

ECM

·

Harness or connector


DTC output confirmation operation (Either condition is met):
·

Within 10 seconds of an engine start operation being performed (with the shift lever in P*2 and the brake pedal*2 or clutch pedal*3 depressed, the engine switch is pressed while the key is being carried). If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).

·

10 seconds after the engine switch is turned on (IG) after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the engine switch being turned on (IG), and DTCs are stored after 6 seconds).



*1: Only output while a malfunction is present.

*2: for Automatic Transmission

*3: for Manual Transmission


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B279986 -

WIRING DIAGRAM

B550360E21
4.969,2.823 5.583,3.156 0.615,0.333 10 false G207 4.99,3 6.563,3.448 1.573,0.448 10 false ID Code Box (Immobiliser Code ECU) 1.688,0.906 2.302,1.24 0.615,0.333 10 false IMO 1.75,1.813 2.365,2.146 0.615,0.333 10 false IMI 1.469,1.469 2.083,1.802 0.615,0.333 10 false +B 6.146,0.24 6.76,0.573 0.615,0.333 10 false +B 0.938,2.875 1.552,3.208 0.615,0.333 10 false G185 5.177,0.906 5.792,1.24 0.615,0.333 10 false EFII 5.188,1.823 5.802,2.156 0.615,0.333 10 false EFIO 2.031,0.885 2.646,1.219 0.615,0.333 10 false 17 2.073,1.781 2.688,2.115 0.615,0.333 10 false 16 4.938,0.896 5.552,1.229 0.615,0.333 10 false 3 4.958,1.823 5.573,2.156 0.615,0.333 10 false 4 0.948,3.052 1.563,3.385 0.615,0.333 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the ID code box (immobiliser code ECU) or ECM, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



HINT:

When DTC B279986 and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin



Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC
2.CLEAR DTC

NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Start the engine.


b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System)>DTC CHECK / CLEAR

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

B279986 is not output.



Result:
Result Proceed to
OK A
NG (DTC B279986 is output) B
NG (Other DTCs are output) C



A

END (REGISTERED COMMUNICATION ID WAS DEFECTIVE)

B

4.INSPECT ECM (TERMINAL IMO)

C

4.INSPECT ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

B598244C02
6.031,0.708 6.469,0.927 0.438,0.219 5.635,2.104 5.781,1.469 true 3.24,4.604 3.021,4.604 3.021,4.604 3.021,4.094 true 2.646,4.604 2.823,4.604 2.823,4.604 2.823,4.25 true 6.094,0.75 6.833,1.052 0.74,0.302 10 false G185 2.906,3.094 3.24,3.281 0.333,0.188 10 false *b 0.26,0.104 0.594,0.292 0.333,0.188 10 false *a 5.552,2.146 5.885,2.333 0.333,0.188 10 false IMO 0.99,4.021 1.49,4.219 0.5,0.198 10 false GND 2.427,4.531 2.76,4.719 0.333,0.188 10 false *c 3.281,4.521 3.615,4.708 0.333,0.188 10 false *d
*a Component with harness connected
(ECM)
*b Waveform
*c Approximately 160 ms *d Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G185-17 (IMO) - Body ground
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected

OK:

The waveform is similar to that shown in the illustration.



Result:
Result Proceed to
Normal waveform A
Terminal IMO stuck low (2.4 V or less) B
Terminal IMO stuck high (12 V) or abnormal waveform C



A

5.INSPECT ECM (TERMINAL IMI)

B

11.INSPECT ECM (IMO TERMINAL VOLTAGE)

C

8.REPLACE ECM
5.INSPECT ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

B598245C02
5.958,0.76 6.427,0.99 0.469,0.229 5.542,2.156 5.875,1.469 true 3.125,4.625 3.271,4.625 3.271,4.625 3.271,4.063 true 3.635,4.625 3.469,4.625 3.469,4.625 3.469,4.063 true 0.167,0.094 0.479,0.25 0.313,0.156 10 false *a 3.667,4.531 3.979,4.688 0.313,0.156 10 false *d 0.948,4.052 1.417,4.208 0.469,0.156 10 false GND 6.021,0.813 6.427,0.99 0.406,0.177 10 false G185 5.438,2.208 5.771,2.375 0.333,0.167 10 false IMI 3.292,3.031 3.604,3.188 0.313,0.156 10 false *b 2.938,4.531 3.25,4.688 0.313,0.156 10 false *c
*a Component with harness connected
(ECM)
*b Waveform
*c Approximately 160 ms *d Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G185-16 (IMI) - Body ground
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected

OK:

The waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

6.REGISTER ECU COMMUNICATION ID

NG

8.REPLACE ECM
6.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER ENGINE STARTS
7.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).


b.

Check that the engine starts 5 seconds after the engine switch turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

8.REPLACE ECM
8.REPLACE ECM
a.

Temporarily replace the ECM with a new one.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.REGISTER ECU COMMUNICATION ID
9.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER ENGINE STARTS
10.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).


b.

Check that the engine starts 5 seconds after the engine switch turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ECM WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

11.INSPECT ECM (IMO TERMINAL VOLTAGE)
a.

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.
E317805C25
1.521,0.375 2.01,0.656 0.49,0.281 2.938,2.167 2.615,1.719 true 0.115,0.198 0.427,0.354 0.313,0.156 10 false *a 1.594,0.448 2.469,0.958 0.875,0.51 10 false G185 2.844,2.208 3.313,2.417 0.469,0.208 10 false IMO
*a Front view of wire harness connector
(to ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Result
G185-17 (IMO) - Body ground Engine switch on (IG) using registered key Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform



Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or abnormal waveform B



A

12.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

B

8.REPLACE ECM
12.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
a.

Disconnect the G207 ID code box (immobiliser code ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G207-3 (EFII) - G185-17 (IMO) Always Below 1 Ω
G207-4 (EFIO) - G185-16 (IMI) Always Below 1 Ω
G185-17 (IMO) - Body ground Always 10 kΩ or higher
G207-3 (EFII) - Body ground Always 10 kΩ or higher
G185-16 (IMI) - Body ground Always 10 kΩ or higher
G207-4 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.

HINT:

Refer to Service Bulletin.


NOTICE:

Recognition code registration is necessary when replacing the ID code box (immobiliser code ECU).

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

14.CHECK WHETHER ENGINE STARTS
14.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).


b.

Check that the engine starts 5 seconds after the engine switch was turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

NG