Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) › from 2020.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261067 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

This DTC is stored when one of the following occurs: 1) the ECM detects errors in its own communication with the transponder key ECU assembly; 2) the ECM detects errors in the communication lines; or 3) the ECU communication ID between the transponder key ECU assembly and ECM is different and an engine start is attempted.

DTC No. DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2799 One of the following conditions is met:
·

Error in communication between ECM and transponder key ECU assembly.

·

Error in communication lines.

·

Communication ID is different during communication between ECM and transponder key ECU assembly.


·

Harness or connector

·

ECM

·

Transponder key ECU assembly


·

Start the engine and wait 10 seconds.

·

After disconnecting and reconnecting the cable to the negative (-) battery terminal, turn the ignition switch to ON and wait 10 seconds.



Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2799 -

WIRING DIAGRAM

B365295E20
0.833,2.229 1.25,2.521 0.417,0.292 10 false ECM 5.5,2.24 6.906,2.552 1.406,0.313 10 false Transponder Key ECU Assembly 1.417,1.156 1.656,1.396 0.24,0.24 10 false IMI 1.375,0.51 1.719,0.76 0.344,0.25 10 false IMO 5.854,0.531 6.25,0.76 0.396,0.229 10 false EFII 5.854,1.281 6.344,1.531 0.49,0.25 10 false EFIO 5.594,1.177 5.833,1.365 0.24,0.188 10 false 13 5.594,0.417 5.833,0.646 0.24,0.229 10 false 12 1.74,1.156 3.583,1.427 1.844,0.271 10 false 10*1, 19*2 1.74,0.396 3.75,0.646 2.01,0.25 10 false 9*1, 18*2 0.844,2.052 3.208,2.271 2.365,0.219 10 false G181*1, G182*2 5.5,2.063 7.021,2.281 1.521,0.219 10 false G74 0.063,3.333 1.594,3.656 1.531,0.323 10 false *2: for 5L-E 0.063,3.021 1.76,3.354 1.698,0.333 10 false *1: for 2TR-FE

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.



HINT:

If the transponder key ECU assembly DTC is output simultaneously, troubleshoot the transponder key ECU assembly DTCs first.


PROCEDURE

2.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.


b.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).

OK:

DTC B2799 is not output.


Result:
Result Proceed to
NG (DTC B2799 is output) A
NG (Other DTCs are output) B
OK C




A

3.INSPECT ECM (TERMINAL IMO)

B

C

3.INSPECT ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

C422061E01
2.875,8.031 2.875,8.333 2.875,8.333 3,8.333 false 4.948,1.552 5,2.073 5,2.073 5.125,2.073 false 4.521,3.635 4.583,4.167 4.583,4.167 4.708,4.167 false 5.99,5.771 6.052,6.292 6.052,6.292 6.177,6.292 false 0.146,0.177 0.635,0.438 0.49,0.26 12 false *A 0.146,0.354 0.635,0.615 0.49,0.26 10 false *a 0.135,2.802 0.625,3.063 0.49,0.26 10 false *a 0.115,4.917 0.604,5.177 0.49,0.26 10 false *a 0.115,2.594 0.604,2.854 0.49,0.26 12 false *B 0.073,4.667 0.563,4.927 0.49,0.26 12 false *C 1.229,0.729 1.615,0.885 0.385,0.156 10 false C153 2.333,0.729 2.719,0.885 0.385,0.156 10 false C154 3.5,0.729 3.885,0.885 0.385,0.156 10 false C155 4.667,0.719 5.052,0.875 0.385,0.156 10 false G181 5.719,0.719 6.104,0.875 0.385,0.156 10 false G180 1.625,2.813 2.01,2.969 0.385,0.156 10 false C153 2.833,2.802 3.219,2.958 0.385,0.156 10 false C154 4.24,2.802 4.625,2.958 0.385,0.156 10 false G181 5.417,2.802 5.802,2.958 0.385,0.156 10 false G180 1.604,4.813 1.99,4.969 0.385,0.156 10 false C161 2.833,4.813 3.219,4.969 0.385,0.156 10 false C162 2.938,6.833 3.323,6.99 0.385,0.156 10 false *b 3.042,7.906 3.427,8.063 0.385,0.156 10 false *d 3.042,8.25 3.427,8.406 0.385,0.156 10 false *c 0.969,7.813 1.469,8.083 0.5,0.271 10 false GND 5.406,4.802 5.792,4.958 0.385,0.156 10 false G183 4.229,4.813 4.615,4.969 0.385,0.156 10 false G182 5.167,2.01 5.552,2.167 0.385,0.156 10 false IMO 4.75,4.094 5.135,4.25 0.385,0.156 10 false IMO 6.198,6.219 6.583,6.375 0.385,0.156 10 false IMO

Text in Illustration
*A for 2TR-FE (for Automatic Transmission) *B for 2TR-FE (for Manual Transmission)
*C for 5L-E - -
*a Component with harness connected
(ECM)
*b Waveform
*c Approximately 160 ms *d Approximately 270 ms

Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
G181-9 (IMO) - Body ground*1
G182-18 (IMO) - Body ground*2
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)


·

*1: for 2TR-FE

·

*2: for 5L-E


OK:

Waveform is similar to that shown in the illustration.


Result:
Result Proceed to
Normal waveform A
Terminal IMO stuck low (2.4 V or less) B
Terminal IMO stuck high (12 V) or abnormal waveform C




A

4.INSPECT ECM (TERMINAL IMI)

B

7.INSPECT ECM (IMO TERMINAL VOLTAGE)

C

11.REPLACE ECM
4.INSPECT ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

C422062E02
3.167,7.99 3.167,8.427 3.167,8.427 3.292,8.427 false 4.875,1.531 4.99,2.063 4.99,2.063 5.115,2.063 false 4.458,3.625 4.604,4.156 4.604,4.156 4.729,4.156 false 5.917,5.771 6.073,6.302 6.073,6.302 6.198,6.302 false 0.146,0.177 0.635,0.438 0.49,0.26 12 false *A 0.146,0.354 0.635,0.615 0.49,0.26 10 false *a 0.125,2.375 0.615,2.635 0.49,0.26 10 false *a 0.125,4.49 0.615,4.75 0.49,0.26 10 false *a 0.115,2.135 0.604,2.396 0.49,0.26 12 false *B 0.115,4.198 0.604,4.458 0.49,0.26 12 false *C 1.229,0.719 1.615,0.875 0.385,0.156 10 false C153 2.344,0.729 2.729,0.885 0.385,0.156 10 false C154 3.49,0.729 3.875,0.885 0.385,0.156 10 false C155 4.646,0.729 5.031,0.885 0.385,0.156 10 false G181 5.708,0.729 6.094,0.885 0.385,0.156 10 false G180 1.615,2.813 2,2.969 0.385,0.156 10 false C153 2.844,2.813 3.229,2.969 0.385,0.156 10 false C154 4.24,2.813 4.625,2.969 0.385,0.156 10 false G181 5.396,2.813 5.781,2.969 0.385,0.156 10 false G180 1.625,4.813 2.01,4.969 0.385,0.156 10 false C161 2.844,4.813 3.229,4.969 0.385,0.156 10 false C162 3.208,6.896 3.594,7.052 0.385,0.156 10 false *b 3.302,8.021 3.688,8.177 0.385,0.156 10 false *d 3.333,8.354 3.719,8.51 0.385,0.156 10 false *c 0.854,7.927 1.354,8.198 0.5,0.271 10 false GND 5.406,4.802 5.792,4.958 0.385,0.156 10 false G183 4.229,4.802 4.615,4.958 0.385,0.156 10 false G182 5.177,1.99 5.563,2.146 0.385,0.156 10 false IMI 4.792,4.083 5.177,4.24 0.385,0.156 10 false IMI 6.24,6.219 6.625,6.375 0.385,0.156 10 false IMI

Text in Illustration
*A for 2TR-FE (for Automatic Transmission) *B for 2TR-FE (for Manual Transmission)
*C for 5L-E - -
*a Component with harness connected
(ECM)
*b Waveform
*c Approximately 160 ms *d Approximately 270 ms

Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
G181-10 (IMI) - Body ground*1
G182-19 (IMI) - Body ground*2
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)


·

*1: for 2TR-FE

·

*2: for 5L-E


OK:

Waveform is similar to that shown in the illustration.




OK

5.REGISTER ECU COMMUNICATION ID

NG

9.REPLACE TRANSPONDER KEY ECU ASSEMBLY
5.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to the Service Bulletin.




NEXT

6.CHECK WHETHER ENGINE STARTS
6.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.




OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

11.REPLACE ECM
7.INSPECT ECM (IMO TERMINAL VOLTAGE)
a.

Disconnect the G181*1 or G182*2 ECM connector.

·

*1: for 2TR-FE

·

*2: for 5L-E


C422063E01
1.708,1.427 1.875,2.25 1.875,2.25 2,2.25 false 4.49,1.583 4.625,2.26 4.625,2.26 4.75,2.26 false 1.813,0.333 2.198,0.49 0.385,0.156 10 false G181 4.75,0.333 5.135,0.49 0.385,0.156 10 false G182 0.354,0.229 0.844,0.49 0.49,0.26 12 false *A 0.354,0.406 0.844,0.667 0.49,0.26 10 false *a 3.896,0.396 4.385,0.656 0.49,0.26 10 false *a 3.854,0.188 4.344,0.448 0.49,0.26 12 false *B 2.052,2.167 2.438,2.323 0.385,0.156 10 false IMO 4.802,2.156 5.188,2.313 0.385,0.156 10 false IMO

Text in Illustration
*A for 2TR-FE *B for 5L-E
*a Front view of wire harness connector
(to ECM)
- -


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G181-9 (IMO) - Body ground*1
G182-18 (IMO) - Body ground*2
Ignition switch turned to ON using registered door control transmitter assembly Terminal IMO stuck low (2.4 V or less)


·

*1: for 2TR-FE

·

*2: for 5L-E


Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or abnormal waveform B




A

8.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)

B

11.REPLACE ECM
8.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the G74 transponder key ECU assembly connector.


b.

Disconnect the G181*1 or G182*2 ECM connector.

·

*1: for 2TR-FE

·

*2: for 5L-E



c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
for 2TR-FE
Tester Connection Condition Specified Condition
G74-12 (EFII) - G181-9 (IMO) Always Below 1 Ω
G74-13 (EFIO) - G181-10 (IMI) Always Below 1 Ω
G74-12 (EFII) or G181-9 (IMO) - Body ground Always 10 kΩ or higher
G74-13 (EFIO) or G181-10 (IMI) - Body ground Always 10 kΩ or higher

for 5L-E
Tester Connection Condition Specified Condition
G74-12 (EFII) - G182-18 (IMO) Always Below 1 Ω
G74-13 (EFIO) - G182-19 (IMI) Always Below 1 Ω
G74-12 (EFII) or G182-18 (IMO) - Body ground Always 10 kΩ or higher
G74-13 (EFIO) or G182-19 (IMI) - Body ground Always 10 kΩ or higher



OK

9.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to the Service Bulletin.


NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly, refer to the Service Bulletin.




NEXT

10.CHECK WHETHER ENGINE STARTS
10.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON

OK:

Engine starts normally.


Result:
Result Proceed to
OK A
NG (for 2TR-FE) B
NG (for 5L-E) C




A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B

C

11.REPLACE ECM
a.

Temporarily replace the ECM with a new one.




NEXT

12.REGISTER ECU COMMUNICATION ID
12.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to the Service Bulletin.




NEXT

13.CHECK WHETHER ENGINE STARTS
13.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON

OK:

Engine starts normally.




OK

END (ECM WAS DEFECTIVE)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY