Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) › from 2020.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261067 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  B279A  Theft Deterrent System Communication Line High Fixation  


DESCRIPTION

If the communication line (EFIO-IMI) to the transponder key ECU assembly is stuck high (e.g. shorted to +B), the ECM stores this DTC.

DTC No. DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B279A Communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck high.
·

Harness or connector

·

ECM

·

Transponder key ECU assembly


Turn the ignition switch to ON and wait 6 seconds.

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops) Engine cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A -

WIRING DIAGRAM

B365296E13
1.052,1.958 2.969,2.156 1.917,0.198 10 false G181*1, G182*2 1.063,2.146 1.458,2.365 0.396,0.219 10 false ECM 5.25,2.156 6.656,2.469 1.406,0.313 10 false Transponder Key ECU Assembly 1.479,1.104 1.781,1.344 0.302,0.24 10 false IMI 5.469,1.104 5.833,1.26 0.365,0.156 10 false EFIO 5.229,1 5.458,1.208 0.229,0.208 10 false 13 1.792,1 3.792,1.198 2,0.198 10 false 10*1, 19*2 5.25,1.958 6.771,2.177 1.521,0.219 10 false G74 0.094,3.24 1.625,3.563 1.531,0.323 10 false *2: for 5L-E 0.094,2.969 1.792,3.302 1.698,0.333 10 false *1: for 2TR-FE

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.



PROCEDURE

2.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.




OK

3.CHECK CONNECTION OF CONNECTOR

NG

3.CHECK CONNECTION OF CONNECTOR
a.

Check that the connectors are properly connected to the ECM and transponder key ECU assembly.

OK:

Connectors are properly connected.




OK

4.CHECK ECM (TERMINAL IMI)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

C422062E02
3.167,7.99 3.167,8.427 3.167,8.427 3.292,8.427 false 4.875,1.531 4.99,2.063 4.99,2.063 5.115,2.063 false 4.458,3.625 4.604,4.156 4.604,4.156 4.729,4.156 false 5.917,5.771 6.073,6.302 6.073,6.302 6.198,6.302 false 0.146,0.177 0.635,0.438 0.49,0.26 12 false *A 0.146,0.354 0.635,0.615 0.49,0.26 10 false *a 0.125,2.375 0.615,2.635 0.49,0.26 10 false *a 0.125,4.49 0.615,4.75 0.49,0.26 10 false *a 0.115,2.135 0.604,2.396 0.49,0.26 12 false *B 0.115,4.198 0.604,4.458 0.49,0.26 12 false *C 1.229,0.719 1.615,0.875 0.385,0.156 10 false C153 2.344,0.729 2.729,0.885 0.385,0.156 10 false C154 3.49,0.729 3.875,0.885 0.385,0.156 10 false C155 4.646,0.729 5.031,0.885 0.385,0.156 10 false G181 5.708,0.729 6.094,0.885 0.385,0.156 10 false G180 1.615,2.813 2,2.969 0.385,0.156 10 false C153 2.844,2.813 3.229,2.969 0.385,0.156 10 false C154 4.24,2.813 4.625,2.969 0.385,0.156 10 false G181 5.396,2.813 5.781,2.969 0.385,0.156 10 false G180 1.625,4.813 2.01,4.969 0.385,0.156 10 false C161 2.844,4.813 3.229,4.969 0.385,0.156 10 false C162 3.208,6.896 3.594,7.052 0.385,0.156 10 false *b 3.302,8.021 3.688,8.177 0.385,0.156 10 false *d 3.333,8.354 3.719,8.51 0.385,0.156 10 false *c 0.854,7.927 1.354,8.198 0.5,0.271 10 false GND 5.406,4.802 5.792,4.958 0.385,0.156 10 false G183 4.229,4.802 4.615,4.958 0.385,0.156 10 false G182 5.177,1.99 5.563,2.146 0.385,0.156 10 false IMI 4.792,4.083 5.177,4.24 0.385,0.156 10 false IMI 6.24,6.219 6.625,6.375 0.385,0.156 10 false IMI

Text in Illustration
*A for 2TR-FE (for Automatic Transmission) *B for 2TR-FE (for Manual Transmission)
*C for 5L-E - -
*a Component with harness connected
(ECM)
*b Waveform
*c Approximately 160 ms *d Approximately 270 ms

Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
G181-10 (IMI) - Body ground*1
G182-19 (IMI) - Body ground*2
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)


·

*1: for 2TR-FE

·

*2: for 5L-E


OK:

Waveform is similar to that shown in the illustration.



Result:
Result Proceed to
NG A
OK (for 2TR-FE) B
OK (for 5L-E) C



A

5.CHECK ECM (TERMINAL IMI)

B

C

5.CHECK ECM (TERMINAL IMI)
a.
B592589E01
1.552,0.26 2.01,0.51 0.458,0.25 2.823,0.5 2.635,0.5 2.635,0.5 2.052,1.302 true 1.646,0.313 2.104,0.51 0.458,0.198 10 false G74 2.938,0.438 3.396,0.635 0.458,0.198 10 false EFIO 0.094,0.115 0.552,0.313 0.458,0.198 10 false *a

Disconnect the transponder key ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G74-13 (EFIO) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Transponder Key ECU Assembly)



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the G74 transponder key ECU assembly connector.


b.

Disconnect the G181*1 or G182*2 ECM connector.


·

*1: for 2TR-FE

·

*2: for 5L-E


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2TR-FE
Tester Connection Condition Specified Condition
G74-13 (EFIO) - G181-10 (IMI) Always Below 1 Ω
G74-13 (EFIO) or G181-10 (IMI) - Body ground Always 10 kΩ or higher

for 5L-E
Tester Connection Condition Specified Condition
G74-13 (EFIO) - G182-19 (IMI) Always Below 1 Ω
G74-13 (EFIO) or G182-19 (IMI) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 2TR-FE
Tester Connection Condition Specified Condition
G181-10 (IMI) - Body ground Always Below 1 V

for 5L-E
Tester Connection Condition Specified Condition
G182-19 (IMI) - Body ground Always Below 1 V



Result:
Result Proceed to
NG A
OK (for 2TR-FE) B
OK (for 5L-E) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C