Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) › from 2020.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261067 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  Engine does not Start but Initial Combustion Occurs  


DESCRIPTION

If the key ID codes of the door control transmitter assembly and transponder key ECU assembly match, the engine immobiliser system is unset and the engine start permission signal is sent to the ECM. When the ID codes of the transponder key ECU assembly and ECM match, the engine starts.

WIRING DIAGRAM

B365295E21
0.844,2.208 1.26,2.417 0.417,0.208 10 false ECM 5.5,2.229 6.927,2.604 1.427,0.375 10 false Transponder Key ECU Assembly 1.417,1.281 1.719,1.448 0.302,0.167 10 false IMI 1.375,0.531 1.719,0.708 0.344,0.177 10 false IMO 5.854,0.51 6.229,0.698 0.375,0.188 10 false EFII 5.854,1.292 6.292,1.49 0.438,0.198 10 false EFIO 5.594,1.167 5.823,1.354 0.229,0.188 10 false 13 5.563,0.417 5.771,0.604 0.208,0.188 10 false 12 1.74,1.146 3.583,1.417 1.844,0.271 10 false 16*1, 10*2, 19*3 1.74,0.406 3.75,0.656 2.01,0.25 10 false 17*1, 9*2, 18*3 0.844,2.031 3.208,2.25 2.365,0.219 10 false G185*1, G181*2, G182*3 5.5,2.063 7.021,2.281 1.521,0.219 10 false G74 0.063,2.896 1.802,3.188 1.74,0.292 10 false *1: for 1GD-FTV 0.063,3.479 1.594,3.802 1.531,0.323 10 false *3: for 5L-E 0.063,3.177 1.76,3.51 1.698,0.333 10 false *2: for 2TR-FE

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to the Service Bulletin.

·

When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.



PROCEDURE

2.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).

Result:
Result Proceed to
NG (for SFI System) A
NG (for ECD System) B
OK C




A

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)

B

4.CHECK WHETHER ENGINE STARTS

C

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine*1 or Engine and ECT*2 / Data List.

*1: for 1GD-FTV

*2: except 1GD-FTV



e.

Read the Data List according to the display on the GTS.

Engine and ECT (except 1GD-FTV)
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status of immobiliser fuel cut / ON or OFF ON: Immobiliser fuel cut on
OFF: Immobiliser fuel cut off
-

Engine (for 1GD-FTV)
Tester Display Measurement Item / Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status Status of immobiliser system fuel cut / OFF/ON ON: Immobiliser fuel cut on
OFF: Immobiliser fuel cut off
-

OK:

OFF is displayed after the ignition switch to ON.


Result:
Result Proceed to
NG A
OK B




A

4.CHECK WHETHER ENGINE STARTS

B

4.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.


Result:
Result Proceed to
NG A
OK B




A

5.CHECK ECM (TERMINAL IMI)

B

5.CHECK ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

B592599E01
3.313,7.833 3.313,8.333 3.313,8.333 3.438,8.333 false 5.729,0.885 5.49,1.458 5.49,1.458 5.292,1.458 false 4.833,2.458 4.896,2.979 4.896,2.979 5.021,2.979 false 4.406,4.073 4.469,4.604 4.469,4.604 4.594,4.604 false 5.865,5.813 5.927,6.333 5.927,6.333 6.052,6.333 false 0.635,0.188 1.302,0.354 0.667,0.167 10 false C149 0.146,0.177 0.635,0.438 0.49,0.26 12 false *A 0.146,0.354 0.635,0.615 0.49,0.26 10 false *a 0.146,1.802 0.635,2.063 0.49,0.26 10 false *a 0.146,3.427 0.635,3.688 0.49,0.26 10 false *a 0.146,5.063 0.635,5.323 0.49,0.26 10 false *a 0.146,1.646 0.635,1.906 0.49,0.26 12 false *B 0.146,3.271 0.635,3.531 0.49,0.26 12 false *C 0.146,4.885 0.635,5.146 0.49,0.26 12 false *D 1.719,0.188 2.396,0.344 0.677,0.156 10 false C150 2.781,0.188 3.365,0.385 0.583,0.198 10 false C151 3.76,0.188 4.302,0.354 0.542,0.167 10 false C152 4.792,0.188 5.438,0.354 0.646,0.167 10 false G184 5.865,0.188 6.667,0.479 0.802,0.292 10 false G185 1.198,1.646 1.583,1.802 0.385,0.156 10 false C153 2.302,1.646 2.688,1.802 0.385,0.156 10 false C154 5.063,1.385 5.448,1.542 0.385,0.156 10 false IMI 3.448,1.646 3.833,1.802 0.385,0.156 10 false C155 4.615,1.646 5,1.802 0.385,0.156 10 false G181 5.677,1.646 6.063,1.802 0.385,0.156 10 false G180 1.583,3.271 1.969,3.427 0.385,0.156 10 false C153 2.802,3.271 3.188,3.427 0.385,0.156 10 false C154 4.198,3.271 4.583,3.427 0.385,0.156 10 false G181 5.375,3.271 5.76,3.427 0.385,0.156 10 false G180 1.583,4.885 1.969,5.042 0.385,0.156 10 false C161 2.802,4.885 3.188,5.042 0.385,0.156 10 false C162 2.323,7.865 2.708,8.021 0.385,0.156 10 false *b 3.458,7.906 3.844,8.063 0.385,0.156 10 false *e 3.469,8.25 3.854,8.406 0.385,0.156 10 false *d 3.385,6.802 3.771,6.958 0.385,0.156 10 false *c 0.969,7.813 1.469,8.083 0.5,0.271 10 false GND 5.375,4.906 5.76,5.063 0.385,0.156 10 false G183 4.188,4.896 4.573,5.052 0.385,0.156 10 false G182 5.042,2.927 5.427,3.083 0.385,0.156 10 false IMI 4.615,4.542 5,4.698 0.385,0.156 10 false IMI 6.073,6.281 6.458,6.438 0.385,0.156 10 false IMI

Text in Illustration
*A for 1GD-FTV *B for 2TR-FE (for Automatic Transmission)
*C for 2TR-FE (for Manual Transmission) *D for 5L-E
*a Component with harness connected
(ECM)
*b Waveform 1
*c Waveform 2 *d Approximately 160 ms
*e Approximately 270 ms - -

Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
G185-16 (IMI) - Body ground*1
G181-10 (IMI) - Body ground*2
G182-19 (IMI) - Body ground*3
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)


·

*1: for 1GD-FTV

·

*2: for 2TR-FE

·

*3: for 5L-E


Result:
Result Proceed to
Normal waveform A
Waveform 1 not output, or has abnormal wavelength or shape B
Waveform 2 not output, or has abnormal wavelength or shape C




A

6.CHECK ECM (TERMINAL IMO)

B

12.CHECK HARNESS AND CONNECTOR ((TRANSPONDER KEY ECU ASSEMBLY - ECM)

C

13.REPLACE TRANSPONDER KEY ECU ASSEMBLY
6.CHECK ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

B592600E01
2.917,7.833 2.917,8.333 2.917,8.333 3.042,8.333 false 5.854,0.885 6.031,1.458 6.031,1.458 6.156,1.458 false 4.938,2.458 4.99,2.979 4.99,2.979 5.115,2.979 false 4.51,4.073 4.573,4.604 4.573,4.604 4.698,4.604 false 5.99,5.813 6.052,6.333 6.052,6.333 6.177,6.333 false 0.854,0.198 1.406,0.375 0.552,0.177 10 false C149 0.146,0.177 0.635,0.438 0.49,0.26 12 false *A 0.146,0.354 0.635,0.615 0.49,0.26 10 false *a 0.146,1.802 0.635,2.063 0.49,0.26 10 false *a 0.146,3.427 0.635,3.688 0.49,0.26 10 false *a 0.146,5.063 0.635,5.323 0.49,0.26 10 false *a 0.146,1.646 0.635,1.906 0.49,0.26 12 false *B 0.146,3.271 0.635,3.531 0.49,0.26 12 false *C 0.146,4.885 0.635,5.146 0.49,0.26 12 false *D 1.938,0.208 2.5,0.385 0.563,0.177 10 false C150 3.01,0.198 3.719,0.385 0.708,0.188 10 false C151 3.948,0.198 4.698,0.396 0.75,0.198 10 false C152 5,0.198 5.604,0.406 0.604,0.208 10 false G184 6.083,0.198 6.625,0.344 0.542,0.146 10 false G185 1.198,1.646 1.583,1.802 0.385,0.156 10 false C153 2.302,1.646 2.688,1.802 0.385,0.156 10 false C154 6.188,1.365 6.573,1.521 0.385,0.156 10 false IMO 3.448,1.646 3.833,1.802 0.385,0.156 10 false C155 4.615,1.646 5,1.802 0.385,0.156 10 false G181 5.677,1.646 6.063,1.802 0.385,0.156 10 false G180 1.583,3.271 1.969,3.427 0.385,0.156 10 false C153 2.802,3.271 3.188,3.427 0.385,0.156 10 false C154 4.198,3.271 4.583,3.427 0.385,0.156 10 false G181 5.375,3.271 5.76,3.427 0.385,0.156 10 false G180 1.583,4.885 1.969,5.042 0.385,0.156 10 false C161 2.802,4.885 3.188,5.042 0.385,0.156 10 false C162 2.938,6.833 3.323,6.99 0.385,0.156 10 false *b 3.042,7.906 3.427,8.063 0.385,0.156 10 false *d 3.083,8.25 3.469,8.406 0.385,0.156 10 false *c 0.969,7.813 1.469,8.083 0.5,0.271 10 false GND 5.375,4.896 5.76,5.052 0.385,0.156 10 false G183 4.188,4.885 4.573,5.042 0.385,0.156 10 false G182 5.146,2.927 5.531,3.083 0.385,0.156 10 false IMO 4.719,4.542 5.104,4.698 0.385,0.156 10 false IMO 6.198,6.281 6.583,6.438 0.385,0.156 10 false IMO

Text in Illustration
*A for 1GD-FTV *B for 2TR-FE (for Automatic Transmission)
*C for 2TR-FE (for Manual Transmission) *D for 5L-E
*a Component with harness connected
(ECM)
*b Waveform
*c Approximately 160 ms *d Approximately 270 ms

Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
G185-17 (IMO) - Body ground*1
G181-9 (IMO) - Body ground*2
G182-18 (IMO) - Body ground*3
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)


·

*1: for 1GD-FTV

·

*2: for 2TR-FE

·

*3: for 5L-E


Result:
Result Proceed to
Normal waveform A
Waveform not output, or has abnormal wavelength or shape B




A

7.REGISTER ECU COMMUNICATION ID

B

9.REPLACE ECM
7.REGISTER ECU COMMUNICATION ID
a.

Register the communication ID between the transponder key ECU assembly and ECM.

HINT:

Refer to the Service Bulletin.




NEXT

8.CHECK WHETHER ENGINE STARTS
8.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.




OK

END (REGISTERED COMMUNICATION ID WAS DEFECTIVE)

NG

13.REPLACE TRANSPONDER KEY ECU ASSEMBLY
9.REPLACE ECM
a.

Temporarily replace the ECM with a new one.




NEXT

10.REGISTER ECU COMMUNICATION ID
10.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to the Service Bulletin.




NEXT

11.CHECK WHETHER ENGINE STARTS
11.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.


Result:
Result Proceed to
OK A
NG (for 2TR-FE) B
NG (for 1GD-FTV) C
NG (for 5L-E) D




A

END (ECM WAS DEFECTIVE)

B

C

D

12.CHECK HARNESS AND CONNECTOR ((TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the G74 transponder key ECU assembly connector.


b.

Disconnect the G185*1, G181*2 or G182*3 ECM connector.

·

*1: for 1GD-FTV

·

*2: for 2TR-FE

·

*3: for 5L-E



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GD-FTV
Tester Connection Condition Specified Condition
G74-13 (EFIO) - G185-16 (IMI) Always Below 1 Ω
G74-13 (EFIO) or G185-16 (IMI) - Body ground Always 10 kΩ or higher

for 2TR-FE
Tester Connection Condition Specified Condition
G74-13 (EFIO) - G181-10 (IMI) Always Below 1 Ω
G74-13 (EFIO) or G181-10 (IMI) - Body ground Always 10 kΩ or higher

for 5L-E
Tester Connection Condition Specified Condition
G74-13 (EFIO) - G182-19 (IMI) Always Below 1 Ω
G74-13 (EFIO) or G182-19 (IMI) - Body ground Always 10 kΩ or higher




OK

13.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to the Service Bulletin.


NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly, refer to the Service Bulletin.




NEXT

14.CHECK WHETHER ENGINE STARTS
14.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.


Result:
Result Proceed to
OK A
NG (for 2TR-FE) B
NG (for 1GD-FTV) C
NG (for 5L-E) D




A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B

C

D