Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Manual Air Conditioning System) › from 2020.08
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261170 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  Air Conditioning Control Panel Circuit  


DESCRIPTION

This circuit consists of the integration control and panel assembly and air conditioning amplifier assembly. When the integration control and panel assembly is operated, signals are transmitted to the air conditioning amplifier assembly through the LIN communication system.

If the LIN communication system malfunctions, the air conditioning amplifier assembly does not operate when the integration control and panel assembly is operated.

WIRING DIAGRAM

w/o Stop and Start System:
E324247E01
5.564,0.452 5.874,0.633 0.310,0.181 10 LIN1 1.431,0.452 1.783,0.633 0.353,0.181 10 LIN1 1.526,1.239 1.771,1.421 0.245,0.181 10 IG 1.407,1.632 1.732,1.813 0.326,0.181 10 ACC 1.833,1.492 1.989,1.674 0.156,0.181 10 6 1.407,2.021 1.732,2.203 0.326,0.181 10 GND 3.744,0.833 4.565,1.007 0.821,0.174 10 from Battery 3.744,1.612 4.855,1.786 1.110,0.174 10 from ACC Relay 3.744,1.215 5.285,1.389 1.541,0.174 10 from IG1 NO.1 Relay 2.715,1.764 3.097,1.945 0.381,0.181 10 ACC 2.676,0.985 3.210,1.167 0.534,0.181 10 ECU-B 2.468,1.375 3.384,1.556 0.916,0.181 10 ECU-IG NO.2 5.419,2.683 6.886,3.089 1.467,0.406 10 Air Conditioning Amplifier Assembly 5.419,2.505 5.748,2.674 0.328,0.169 10 G25 0.469,2.626 2.312,2.960 1.843,0.333 10 Integration Control and Panel Assembly 0.886,3.28 2.501,3.461 1.615,0.181 10 : LIN Communication Line 5.295,0.285 5.466,0.466 0.171,0.181 10 37 1.833,0.726 1.989,0.907 0.156,0.181 10 1 1.833,1.131 1.989,1.312 0.156,0.181 10 5 1.833,1.882 1.989,2.063 0.156,0.181 10 4 1.822,0.285 1.972,0.466 0.149,0.181 10 3 0.468,2.481 0.772,2.665 0.304,0.184 10 G23 1.526,0.835 1.771,1.017 0.245,0.181 10 +B

w/ Stop and Start System:
E454770E01
5.563,0.448 5.875,0.625 0.313,0.177 10 false LIN1 1.427,0.448 1.781,0.625 0.354,0.177 10 false LIN1 1.521,1.24 1.771,1.417 0.25,0.177 10 false IG 1.406,1.635 1.729,1.813 0.323,0.177 10 false ACC 1.833,1.49 1.99,1.667 0.156,0.177 10 false 6 1.406,2.021 1.729,2.198 0.323,0.177 10 false GND 2.979,0.823 5.125,1.021 2.146,0.198 10 false from Engine Stop and Start ECU 5.417,2.688 6.885,3.094 1.469,0.406 10 false Air Conditioning Amplifier Assembly 5.417,2.5 5.74,2.667 0.323,0.167 10 false G25 0.469,2.625 2.313,2.958 1.844,0.333 10 false Integration Control and Panel Assembly 0.885,3.281 2.5,3.458 1.615,0.177 10 false : LIN Communication Line 5.25,0.281 5.417,0.458 0.167,0.177 10 false 37 1.833,0.729 1.99,0.906 0.156,0.177 10 false 1 1.833,1.135 1.99,1.313 0.156,0.177 10 false 5 1.833,1.885 1.99,2.063 0.156,0.177 10 false 4 1.823,0.281 1.969,0.458 0.146,0.177 10 false 3 0.469,2.479 0.771,2.667 0.302,0.188 10 false G23 1.521,0.833 1.771,1.01 0.25,0.177 10 false +B 2.969,1.229 5.115,1.427 2.146,0.198 10 false from Engine Stop and Start ECU 2.99,1.615 5.135,1.813 2.146,0.198 10 false from Engine Stop and Start ECU

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL AND PANEL - AIR CONDITIONING AMPLIFIER)
a.

Disconnect the G25 amplifier connector.


b.

Disconnect the G23 panel connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G23-3 (LIN1) - G25-37 (LIN1) Always Below 1 Ω
G23-3 (LIN1) - Body ground Always 10 kΩ or higher




OK

2.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL AND PANEL - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL AND PANEL - BATTERY AND BODY GROUND)
a.
U149299E03
2.052,1.031 2.75,0.615 true 1.375,1.354 0.792,1.656 true 0.76,0.531 1.375,1.021 true 1.667,1.302 2,1.802 true 0.115,0 0.385,0.188 0.271,0.188 10 false *a 0.49,1.594 0.823,1.781 0.333,0.188 10 false IG+ 2.802,0.51 3.177,0.698 0.375,0.188 10 false GND 0.448,1.021 0.76,1.208 0.313,0.188 10 false G23 0.5,0.396 0.74,0.583 0.24,0.188 10 false +B 2.01,1.792 2.385,1.979 0.375,0.188 10 false ACC

Disconnect the G23 panel connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Stop and Start System::
Tester Connection Switch Condition Specified Condition
G23-1 (+B) - G23-4 (GND) Always 11 to 14 V
G23-5 (IG) - G23-4 (GND) Ignition switch off Below 1 V
G23-5 (IG) - G23-4 (GND) Ignition switch ON 11 to 14 V
G23-6 (ACC) - G23-4 (GND) Ignition switch off Below 1 V
G23-6 (ACC) - G23-4 (GND) Ignition switch ACC 11 to 14 V

w/ Stop and Start System::
Tester Connection Switch Condition Specified Condition
G23-1 (+B) - G23-4 (GND) Always 10.5 to 16 V
G23-5 (IG) - G23-4 (GND) Ignition switch off Below 1 V
G23-5 (IG) - G23-4 (GND) Ignition switch ON 10.5 to 16 V
G23-5 (IG) - G23-4 (GND) Ignition switch off Below 1 V
G23-6 (ACC) - G23-4 (GND) Ignition switch ACC 10.5 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G23-4 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Integration Control and Panel Assembly)

Result:
Result Proceed to
OK A
NG (w/o Stop and Start System) B
NG (w/ Stop and Start System) C



A

3.CHECK INTEGRATION CONTROL AND PANEL ASSEMBLY

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

3.CHECK INTEGRATION CONTROL AND PANEL ASSEMBLY
a.

Replace the integration control and panel assembly with a new or normally functioning one (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL>REMOVAL).


b.

Operate the integration control and panel assembly to check that it functions properly.

OK:

Integration control and panel assembly operates normally.




OK

END (INTEGRATION CONTROL AND PANEL ASSEMBLY IS FAULTY)

NG