Wear protective gloves. Sharp areas on the parts may injure your hands.
71844D
1.REMOVE REAR SEAT RECLINING COVER LH
Remove the 2 screws.
Using a moulding remover, detach the 2 claws.
Move the cover in the direction of the arrow to detach the guide and remove the cover.
71833A
2.REMOVE REAR NO. 1 SEAT RECLINING COVER RH
Remove the 2 screws.
Using a moulding remover, detach the 2 claws.
Move the cover in the direction of the arrow to detach the guide.
Detach the 2 hooks and remove the cover.
71324G
3.REMOVE REAR NO. 2 SEAT CUSHION
Remove the screw and cushion.
71876K
4.REMOVE REAR RECLINING ADJUSTER INSIDE COVER LH
Remove the 2 screws.
Detach the 2 claws and remove the cover.
72205B
5.REMOVE SEAT TRACK OPEN LEVER PIN SUB-ASSEMBLY
Using a screwdriver, remove the stopper.
Remove the pin as shown in the illustration.
Use the same procedure for both pins.
72779
6.REMOVE REAR SEAT HINGE PAWL GUIDE
Detach the 4 claws and remove the pawl guide.
Use the same procedure for both pawl guides.
71302D
7.REMOVE REAR SEAT HINGE SUB-ASSEMBLY LH
Using a screwdriver, remove the E-ring.
Remove the pin.
Using a screwdriver, detach the 10 claws.
Tape the screwdriver tip before use.
Remove the 5 screws.
Disconnect the reclining release handle from the under cover.
Raise the under cover.
Using a screwdriver, remove the spring of the seat stay ball-joint.
Disconnect the seat stay from the seat cushion frame.
Remove the seat hinge and seat stay as a unit.
The seat stay cannot be disconnected from the seat hinge. If the stay is disconnected from the hinge, replacement of both parts is necessary.
If it is necessary to replace the seat hinge, replace it together with the seat stay as the stay cannot be disconnected from the hinge.
71305C
8.REMOVE REAR SEAT STAY SUB-ASSEMBLY
As the seat stay cannot be disconnected from the seat hinge, it is removed in the previous step.
If it is necessary to replace the seat stay, replace it together with the seat hinge as the stay cannot be disconnected from the hinge.
71301D
9.REMOVE REAR SEAT HINGE SUB-ASSEMBLY RH
Using a screwdriver, remove the E-ring.
Remove the pin and hinge.
71647G
10.REMOVE REAR SEAT CUSHION EDGE PROTECTOR
Remove the protector from the cushion frame.
Use the same procedure for both protectors.
78917
11.REMOVE FOLD SEAT LEG LOCK CUSHION
Remove the cushion from the protector.
Use the same procedure for both cushions.
72649
12.REMOVE REAR SEAT CUSHION SUPPORT SPRING
Remove the spring from the seat cushion frame.
Use the same procedure for both springs.
72908B
13.REMOVE REAR SEAT CUSHION UNDER COVER SUB-ASSEMBLY LH
Remove the under cover.
71586
14.REMOVE REAR NO. 2 SEAT HINGE COVER LH
Detach the 3 claws and remove the cover.
71585
15.REMOVE REAR NO. 2 SEAT HINGE COVER RH
Detach the 3 claws and remove the cover.
16.REMOVE SEAT CUSHION COVER WITH PAD
| *a | Tack Pin |
Cut off the tack pins and remove the carpet from the cushion pad.
Remove the hog rings and seat cushion cover with pad.
73390A
17.REMOVE REAR SEAT INNER BELT ASSEMBLY
73380C
18.REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY RH
71647F
19.REMOVE REAR SEAT INNER CUSHION EDGE PROTECTOR LH
| *a | Tack Pin |
Cut off the tack pins and remove the carpet from the cushion pad.
71076S
20.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER
Remove the hog rings and seat cushion cover from the seat cushion pad.
72996A
21.REMOVE REAR SEATBACK COVER
Using a screwdriver, detach the 8 claws and remove the 2 covers.
Tape the screwdriver tip before use.
79185
22.REMOVE NO. 1 SEATBACK PAD LH
Remove the bolt and disconnect the outer belt.
| *a | Fastening Tape |
Detach the fastening tape and open the cover.
Remove the 6 hog rings.
Open the 2 fasteners, and then open the seatback cover.
Remove the seatback pad.
71837D
23.REMOVE REAR SEAT INNER RECLINING COVER RH
Remove the screw.
Detach the guide and remove the cover.
72830
24.REMOVE REAR SEAT CENTER ARMREST ASSEMBLY
Remove the 2 bolts, center armrest and bush.
71281A
25.REMOVE REAR SEAT CENTER ARMREST HINGE
Remove the screw and armrest hinge.
71956C
26.REMOVE REAR SEAT ARMREST SUPPORT
Remove the armrest support.
73237A
27.REMOVE SHOULDER BELT ANCHOR COVER
| *a | Protective Tape |
Using a screwdriver, detach the 2 claws and 2 guides, and then remove the cover.
Tape the screwdriver tip before use.
73375B
28.REMOVE REAR SEAT SHOULDER BELT HOLE COVER LH
Detach the 4 claws and remove the cover.
Disconnect the outer belt.
72615C
29.REMOVE REAR SEATBACK LOCK STRIKER COVER
| *a | Protective Tape |
Using a screwdriver, detach the claw and guide, and then remove the cover.
Tape the screwdriver tip before use.
72058A
30.REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH
Remove the 2 screws.
Disconnect the cable in the order shown in the illustration and remove the lever.
71931B
31.REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
Detach the 8 claws and remove the 4 supports.
32.REMOVE SEATBACK COVER WITH PAD
Detach the 2 hooks and remove the seatback cover with pad.
Disconnect the outer belt from the seatback cover with pad.
71078S
33.REMOVE SEPARATE TYPE REAR SEATBACK COVER
Remove the hog rings and detach the fastening tape, and then remove the seatback cover from the seatback pad.
| *a | Fastening Tape | - | - |
71834H
34.REMOVE REAR NO. 1 SEAT RECLINING COVER LH
Detach the 2 claws and remove the cover.
71812C
35.REMOVE RECLINING ADJUSTER COVER LH
Remove the 4 screws.
Detach the 4 claws and remove the cover.
73187A
36.REMOVE REAR SEAT SHOULDER BELT GUIDE
Detach the 2 claws and open the cover.
Disconnect the seat belt from the belt guide.
Detach the 4 guides and remove the belt guide.
73320A
37.REMOVE NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH
72620B
38.REMOVE REAR NO. 1 SEAT LOCK CABLE ASSEMBLY
Detach the 2 cable clamps, and then disconnect the cable and remove it.
71879F
39.REMOVE REAR SEAT INNER RECLINING COVER LH
Detach the 2 claws and 2 guides, and then remove the cover.
71879E
40.REMOVE REAR SEAT RECLINING COVER INNER LH
Detach the 2 guides and remove the cover.
71878E
41.REMOVE REAR SEAT RECLINING COVER INNER RH
Detach the 2 guides and remove the cover.
72569
42.REMOVE SEATBACK STOPPER PLATE
Remove the 3 bolts and plate.
72830B
43.REMOVE REAR CENTER SEAT ARMREST BUSH
Detach the 3 claws and remove the bush.
71018
44.REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY LH
Remove the 4 bolts, bracket and seatback frame.
72720B
45.REMOVE REAR SEATBACK INNER ADJUSTER ASSEMBLY LH
Remove the 2 bolts, adjuster and cover.
73709A
46.REMOVE TETHER ANCHOR BRACKET SUB-ASSEMBLY
Remove the bolt and bracket.
78920B
47.REMOVE NO. 1 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY LH
Cut off the 2 cable ties.
Detach the 3 cable clamps, and then disconnect the cable and remove it.