Wear protective gloves. Sharp areas on the parts may injure your hands.
71834A
1.REMOVE REAR NO. 1 SEAT RECLINING COVER LH
Remove the 2 screws.
Using a moulding remover, detach the 2 claws.
Move the cover in the direction of the arrow to detach the guide.
Detach the 2 hooks and remove the cover.
71833A
2.REMOVE REAR NO. 1 SEAT RECLINING COVER RH
Remove the 2 screws.
Using a moulding remover, detach the 2 claws.
Move the cover in the direction of the arrow to detach the guide and remove the cover.
72205B
3.REMOVE SEAT TRACK OPEN LEVER PIN SUB-ASSEMBLY
Using a screwdriver, remove the stopper.
Remove the pin as shown in the illustration.
Use the same procedure for both pins.
72779
4.REMOVE REAR SEAT HINGE PAWL GUIDE
Detach the 4 claws and remove the pawl guide.
Use the same procedure for both pawl guides.
71302B
5.REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH
Using a screwdriver, remove the E-ring.
Remove the pin and hinge.
71301B
6.REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH
Using a screwdriver, remove the E-ring.
Remove the pin.
Using a screwdriver, detach the 6 claws.
Tape the screwdriver tip before use.
Remove the 4 screws.
Disconnect the reclining release handle from the under cover.
Raise the under cover.
Using a screwdriver, remove the spring of the seat stay ball-joint.
Disconnect the seat stay.
Remove the seat hinge and seat stay as a unit.
The seat stay cannot be disconnected from the seat hinge. If the stay is disconnected from the hinge, replacement of both parts is necessary.
If it is necessary to replace the seat hinge, replace it together with the seat stay as the stay cannot be disconnected from the hinge.
71305C
7.REMOVE REAR SEAT STAY SUB-ASSEMBLY
As the seat stay cannot be disconnected from the seat hinge, it is removed in the previous step.
If it is necessary to replace the seat stay, replace it together with the seat hinge as the stay cannot be disconnected from the hinge.
71647G
8.REMOVE REAR SEAT CUSHION EDGE PROTECTOR
Remove the protector from the cushion frame.
Use the same procedure for both protectors.
78917
9.REMOVE FOLD SEAT LEG LOCK CUSHION
Remove the cushion from the protector.
Use the same procedure for both cushions.
72649
10.REMOVE REAR SEAT CUSHION SUPPORT SPRING
Remove the spring from the seat cushion frame.
Use the same procedure for both springs.
72907B
11.REMOVE REAR SEAT CUSHION UNDER COVER SUB-ASSEMBLY RH
Remove the under cover.
71586
12.REMOVE REAR NO. 2 SEAT HINGE COVER LH
Detach the 3 claws and remove the cover.
71585
13.REMOVE REAR NO. 2 SEAT HINGE COVER RH
Detach the 3 claws and remove the cover.
14.REMOVE SEAT CUSHION COVER WITH PAD
| *a | Tack Pin |
Cut off the tack pins and remove the carpet from the cushion pad.
Remove the 3 hog rings and seat cushion cover with pad.
73390C
15.REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH
71647D
16.REMOVE REAR SEAT INNER CUSHION EDGE PROTECTOR RH
| *a | Tack Pin |
Cut off the tack pins and remove the carpet from the cushion pad.
71075S
17.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER
Remove the hog rings and seat cushion cover from the seat cushion pad.
72996A
18.REMOVE REAR SEATBACK COVER
Using a screwdriver, detach the 4 claws and remove the cover.
Tape the screwdriver tip before use.
79175
19.REMOVE NO. 1 SEATBACK PAD RH
| *a | Fastening Tape |
Detach the fastening tape and open the cover.
Remove the 3 hog rings.
Open the 2 fasteners, and then open the seatback cover.
Remove the seatback pad.
72615C
20.REMOVE REAR SEATBACK LOCK STRIKER COVER
| *a | Protective Tape |
Using a screwdriver, detach the claw and guide, and then remove the cover.
Tape the screwdriver tip before use.
72057
21.REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH
Remove the 2 screws.
Disconnect the cable in the order shown in the illustration and remove the lever.
71931B
22.REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
Detach the 4 claws and remove the 2 supports.
23.REMOVE SEATBACK COVER WITH PAD
Detach the 2 hooks and remove the seatback cover with pad.
71077S
24.REMOVE SEPARATE TYPE REAR SEATBACK COVER
| *a | Fastening Tape |
Detach the 2 fastening tapes.
Remove the hog rings and seatback cover from the seatback pad.
72620B
25.REMOVE REAR NO. 1 SEAT LOCK CABLE ASSEMBLY
Detach the 2 cable clamps, and then disconnect the cable and remove it.
71879E
26.REMOVE REAR SEAT INNER RECLINING COVER LH
Detach the 2 claws and 2 guides, and then remove the cover.
71878F
27.REMOVE REAR SEAT INNER RECLINING COVER RH
Detach the 2 claws and 2 guides, and then remove the cover.
71834H
28.REMOVE REAR SEAT RECLINING COVER INNER LH
Detach the 2 guides and remove the cover.
71878E
29.REMOVE REAR SEAT RECLINING COVER INNER RH
Detach the 2 guides and remove the cover.
71017
30.REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY RH
Remove the 4 bolts and seatback frame.
78910B
31.REMOVE NO. 1 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY RH
Cut off the 2 cable ties.
Detach the 3 cable clamps, and then disconnect the cable and remove it.