Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
71846A
1.REMOVE REAR SEAT UPPER RECLINING COVER LH
| *a | Protective Tape |
Using a screwdriver, detach the 3 claws and remove the rear seat upper reclining cover LH.
Tape the screwdriver tip before use.
72526A
2.REMOVE RECLINING ADJUSTER RELEASE HANDLE LH
Remove the 3 screws and reclining adjuster release handle LH.
71395B
3.REMOVE CENTER SEAT HINGE COVER LH
Using a clip remover, remove the clip.
Detach the 2 guides and remove the center seat hinge cover LH.
71826B
4.REMOVE REAR SEAT CUSHION MOULDING LH
Using a clip remover, detach the clip.
Using a moulding remover, detach the 3 claws.
Move the rear seat cushion moulding LH in the direction of the arrow to detach the guide and remove the rear seat cushion moulding LH.
72616A
5.REMOVE REAR SEATBACK LOCK STRIKER COVER LH
Using a clip remover, detach the 3 clips and remove the rear seatback lock striker cover LH.
6.REMOVE SEAT CUSHION COVER WITH PAD
w/ Seat Heater System:
Disconnect the 2 rear seat heater connectors.
Pull out the wire harness as shown in the illustration.
Detach the hooks.
Detach the hook and remove the seat cushion cover with pad.
71696
7.REMOVE REAR NO. 2 SEAT PROTECTOR
Remove the 2 rear No. 2 seat protectors from the separate type rear seat cushion pad.
71076S
8.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER
Remove the 14 hog rings and separate type rear seat cushion cover from the separate type rear seat cushion pad.
87510P
9.REMOVE REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)
71647
10.REMOVE REAR SEAT CUSHION EDGE PROTECTOR
Remove the rear seat cushion edge protector from the cushion spring.
11.REMOVE CENTER SEATBACK ASSEMBLY
Remove the 2 bolts and center seatback assembly.
71960B
12.REMOVE REAR SEAT CENTER HEADREST ASSEMBLY
Remove the rear seat center headrest assembly.
71397A
13.REMOVE CENTER SEAT HINGE COVER
Using a clip remover, remove the clip.
Detach the 2 guides and remove the center seat hinge cover.
72732
14.REMOVE REAR SEAT RECLINING BRACKET LH
Using a T45 "TORX" socket wrench, remove the "TORX" bolt, bush and rear seat reclining bracket LH.
72731
15.REMOVE REAR SEAT RECLINING BRACKET RH
Using a T45 "TORX" socket wrench, remove the "TORX" bolt, bush and rear seat reclining bracket RH.
71369B
16.REMOVE REAR SEATBACK STAY COVER LH
Using a moulding remover, detach the 3 claws.
Detach the guide and remove the rear seatback stay cover LH.
71349B
17.REMOVE REAR SEATBACK STAY COVER RH
Using a moulding remover, detach the 3 claws.
Detach the guide and remove the rear seatback stay cover RH.
72830
18.REMOVE REAR SEAT CENTER ARMREST ASSEMBLY
Using a T45 "TORX" socket wrench, remove the 2 "TORX" bolts and 2 bushes.
Remove the nut and rear center seat armrest support LH.
Remove the rear seat center armrest assembly as shown in the illustration.
72806B
19.REMOVE REAR SEAT CENTER ARMREST CUP HOLDER SUB-ASSEMBLY
Remove the 2 screws.
Using moulding remover A, detach the 2 claws and remove the rear seat center armrest cup holder sub-assembly.
72996A
20.REMOVE REAR SEATBACK COVER
Using a screwdriver, detach the 4 claws and remove the rear seatback cover.
Tape the screwdriver tip before use.
72665B
21.REMOVE REAR SEATBACK LOCK COVER
Using a moulding remover, detach the claw.
Move the cover in the direction of the arrow to detach the clip and 2 guides, and then remove the rear seatback lock cover.
71087
22.REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY
Using a clip remover, detach the 5 clips and remove the rear seatback board sub-assembly.
72877C
23.REMOVE SEAT ARMREST COVER
Detach the hooks.
Remove the seat armrest cover with pad.
Remove the seat armrest cover from the pad.
71931A
24.REMOVE REAR SEAT HEADREST SUPPORT
Detach the 4 claws and remove the 2 rear seat headrest supports.
79157
25.REMOVE NO. 1 SEATBACK COVER
Using moulding remover A, detach the 2 claws.
Detach the guide and remove the No. 1 seatback cover.
72660F
26.REMOVE REAR SEAT LOCK ASSEMBLY LH
Detach the clamp and disconnect the wire.
Remove the 2 bolts and rear seat lock assembly LH.
72663
27.REMOVE REAR NO. 1 SEAT LOCK CONTROL LEVER
Remove the rear No. 1 seat lock control lever as shown in the illustration.
79873
28.REMOVE FOLD SEATBACK WIRE
Detach the 2 claws and remove the fold seatback wire.
74633A
29.REMOVE COAT HOOK CAP
| *a | Protective Tape |
Using a screwdriver, detach the 2 claws and guide, and then remove the coat hook cap.
Tape the screwdriver tip before use.
72978
30.REMOVE CENTER NO. 2 SEATBACK COVER
Remove the 3 screws and center No. 2 seatback cover.
73390C
31.REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH
w/ Seat Belt Warning System:
Disconnet the connector and detach the clamp.
Remove the bolt and rear No. 1 seat inner belt assembly LH and disconnect the No. 1 seat 3 point type belt assembly LH.
72572C
32.REMOVE RECLINING ADJUSTER KNOB CAP LH
| *a | Protective Tape |
Using a screwdriver, detach the claw and guide, and then remove the reclining adjuster knob cap LH.
Tape the screwdriver tip before use.
72058A
33.REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH
Remove the 2 screws.
Disconnect the cable in the order shown in the illustration and remove the rear seat lock control lever sub-assembly LH.
73178A
34.REMOVE SEAT BELT ANCHOR COVER CAP
| *a | Protective Tape |
Using a screwdriver, detach the 2 claws and remove the seat belt anchor cover cap.
Tape the screwdriver tip before use.
73373
35.REMOVE REAR SEAT SHOULDER BELT COVER
Disconnect the outer belt from the rear seat shoulder belt cover.
Detach the 2 claws and 2 guides, and then remove the rear seat shoulder belt cover.
72996A
36.REMOVE REAR SEATBACK COVER
Using a screwdriver, detach the 4 claws and remove the rear seatback cover.
Tape the screwdriver tip before use.
71890A
37.REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY LH
Using a clip remover, detach the 7 clips and remove the rear seatback board carpet assembly LH.
71931B
38.REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
Detach the 4 claws and remove the 2 rear No. 1 seat headrest support assemblies.
39.REMOVE SEATBACK COVER WITH PAD
| *a | Hook |
| *b | Hog Ring |
Remove the 10 hog rings and detach the hooks, and then remove the seatback cover with pad.
Disconnect the outer belt from the seatback cover with pad.
w/ Seat Heater System:
Remove the wire harness.
71078S
40.REMOVE SEPARATE TYPE REAR SEATBACK COVER
w/ Seat Heater System:
Disconnect the rear seatback heater assembly wire harness from the separate type rear seatback pad.
Remove the 8 hog rings and separate type rear seatback cover from the separate type rear seatback pad.
87510Q
41.REMOVE REAR SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)
71697
42.REMOVE REAR SEATBACK EDGE PROTECTOR
Remove the rear seatback edge protector from the rear seatback frame sub-assembly LH.
71879A
43.REMOVE REAR SEAT INNER RECLINING COVER LH
Remove the 2 screws.
Detach the guide and remove the rear seat inner reclining cover LH.
71876J
44.REMOVE RECLINING ADJUSTER INSIDE COVER LH
Remove the 2 screws.
Detach the 2 claws and remove the reclining adjuster inside cover LH.
71828B
45.REMOVE REAR SEAT REAR CUSHION MOULDING LH
Using a clip remover, detach the clip.
Using moulding remover A, detach the 4 claws.
Move the rear seat rear cushion moulding LH in the direction of the arrow to detach the guide and remove the rear seat rear cushion moulding LH.
73949
46.REMOVE CAP
Detach the 2 claws and remove the cap.
71879B
47.REMOVE REAR SEAT RECLINING COVER INNER LH
Detach the claw and guide, and then remove the rear seat reclining cover inner LH.
71499C
48.REMOVE REAR SEAT CUSHION SPRING DAMPER
Remove the 2 nuts and rear seat cushion spring damper.
73187A
49.REMOVE REAR SEAT SHOULDER BELT GUIDE
Detach the claw and guide, and then remove the rear seat shoulder belt guide.
73320A
50.REMOVE NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH
72704A
51.REMOVE REAR SEAT RECLINING CONTROL CABLE
Cut off the 4 cable ties.
Detach the 3 cable clamps and disconnect the cable, and then remove the rear seat reclining control cable.
72704B
52.REMOVE REAR NO. 2 SEAT RECLINING CONTROL CABLE
Detach the 3 cable clamps and disconnect the cable, and then remove the rear No. 2 seat reclining control cable.
72068
53.REMOVE REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY LH
Remove the 2 nuts and rear back lock control lever sub-assembly LH.
87501D
54.REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)
82194
55.REMOVE REAR SEAT WIRE LH (w/ Seat Wire Harness)
| *A | w/ Seat Belt Warning System |
Detach the claw and disconnect the rear seat wire connector.
Detach the clamp and remove the rear seat wire LH.
71018
56.REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY LH
Using a T45 "TORX" socket wrench, remove the 2 "TORX" bolts.
Remove the 2 bolts and rear seatback frame sub-assembly LH.
72728
57.REMOVE REAR SEAT INNER RECLINING PROTECTOR RH
Detach the claw and guide to remove the rear seat inner reclining protector RH.
71016A
58.REMOVE REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH
Remove the 6 nuts and rear seat cushion frame sub-assembly LH.
72173B
59.REMOVE REAR SEAT TRACK ADJUSTING HANDLE LH
Slide the slide rail to the rearmost position.
Using a small screwdriver, push down the handle stopper to detach the claw and remove the rear seat track adjusting handle LH.
Insert the screwdriver into the hole shown in the illustration while looking into the hole.