Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
79040
1.INSTALL NO. 3 SEAT LEG ASSEMBLY LH
Attach the 4 clips to install the seat cushion under carpet LH to the No. 3 seat leg.
79020B
2.INSTALL NO. 2 SEAT LEG ASSEMBLY (for RH Side)
Attach the 4 clips to install the seat cushion under carpet RH to the No. 2 seat leg.
82196
3.INSTALL REAR NO.2 SEAT WIRE LH (w/ Seat Belt Warning System)
Attach the wire harness clamp to install the rear No. 2 seat wire LH.
82824
4.INSTALL WIRING HARNESS CONNECTOR (w/ Seat Belt Warning System)
Attach the claw and install the wiring harness connector.
Install the warning reflector holder.
79304A
5.INSTALL NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH
Using a T45 "TORX" socket wrench, install the seatback frame with the 4 "TORX" bolts.
79226
6.INSTALL NO. 2 SEAT LOCK CABLE
| *a | Clamp |
| *b | Cable End |
Twist the cable end in the direction indicated by the arrow to connect it.
Attach the clamp to install the cable.
78091
7.INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY
| *a | Clamp A |
| *b | Clamp B |
| *c | Cable Tie |
| *d | Cable End |
Twist the cable end in the direction indicated by the arrow to connect it.
Attach the 2 clamps labeled A to install the cable.
Install the clamp labeled B together with the No. 2 seat lock cable.
Install 2 new cable ties.
71844A
8.INSTALL REAR NO. 2 SEAT OUTER RECLINING COVER LH
Attach the 2 claws and guide to install the cover.
Install the screw.
71844C
9.INSTALL REAR NO. 2 SEAT INNER RECLINING COVER LH
Attach the 5 claws to install the cover.
71834C
10.INSTALL REAR NO. 3 SEAT OUTER RECLINING COVER LH
Attach the 2 claws and guide to install the cover.
Install the screw.
71834C
11.INSTALL REAR NO. 3 SEAT INNER RECLINING COVER LH
Attach the 4 claws to install the cover.
79962
12.INSTALL NO. 2 SEATBACK COVER
Attach the 2 claws to install the cover.
71587C
13.INSTALL REAR NO. 2 SEATBACK EDGE PROTECTOR
Install the protector to the seatback pad with new tack pins.
79034
14.INSTALL REAR NO. 3 SEATBACK COVER SUB-ASSEMBLY LH
Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.
| *a | Hog Ring Pliers | - | - |
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
15.INSTALL SEATBACK COVER WITH PAD
Attach the hooks to install the seatback cover with pad.
71931C
16.INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY
Attach the 4 claws to install the 2 headrest supports.
71702C
17.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH
Attach the 7 clips to install the board.
72690A
18.INSTALL REAR SEAT LOCK RELEASE LEVER ASSEMBLY
| *a | Cable End |
| *b | No. 2 Seat Lock Cable |
| *c | Fold Seat Lock Control Cable |
| *d | Clamp |
Twist the 2 cable ends in the direction indicated by the arrow to connect them.
Attach the 2 clamps.
Attach the hook.
Install the lever with the 2 screws.
72615G
19.INSTALL REAR NO. 2 SEATBACK LOCK STRIKER COVER
| *a | Guide |
Attach the guide and claw to install the cover.
66310F
20.INSTALL ROPE HOOK ASSEMBLY
Install the rope hook with the bolt.
Attach the 2 claws to close the cover.
72058B
21.INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH
| *a | Clamp |
| *b | Cable End |
| *c | Guide |
Twist the cable end in the direction indicated by the arrow to connect it.
Attach the clamp.
Attach the guide to install the lever.
Install the 2 screws.
72615H
22.INSTALL REAR NO. 1 SEATBACK LOCK STRIKER COVER
| *a | Guide |
Attach the guide and claw to install the cover.
72695C
23.INSTALL REAR SEAT LOCK CONTROL CABLE LH
| *a | Clamp |
| *b | Cable End |
Twist the cable end in the direction indicated by the arrow to connect it.
Attach the clamp to install the cable.
71694E
24.INSTALL REAR SEAT CUSHION INNER HINGE COVER RH
Attach the guide to install the cover.
Install the clip and screw.
71694E
25.INSTALL REAR SEAT CUSHION INNER HINGE COVER LH
Attach the guide to install the cover.
Install the clip and screw.
73590
26.INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY LH
79384A
27.INSTALL REAR NO. 3 SEAT LEG COVER LH
Attach the 2 claws to install the cover.
79384
28.INSTALL REAR SEAT LEG COVER LH
Attach the 5 clips and 3 hooks to install the cover.
Install the clip.
72058B
29.INSTALL REAR NO. 2 SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH
Attach the 2 guides.
Install the lever with the screw.
| *a | Cable End |
| *b | Clamp |
Twist the cable end in the direction indicated by the arrow to connect it.
Attach the clamp.
72906
30.INSTALL 3RD SEAT LINK SUB-ASSEMBLY LH
Attach the 4 guides and 2 claws to install the link.
Install the 3 clips.
79202
31.INSTALL NO. 2 SEAT CUSHION FRAME SUB-ASSEMBLY LH
Using a T40 "TORX" socket wrench, install the seat cushion frame with the 4 "TORX" bolts.
Pull out the seat cushion frame.
71827B
32.INSTALL REAR NO. 2 SEAT CUSHION MOULDING
Attach the 2 claws to install the moulding.
Install the 2 screws.
71647F
33.INSTALL REAR SEAT CUSHION INNER EDGE PROTECTOR LH
Install the protector to the seat cushion pad with new tack pins.
79032
34.INSTALL NO. 3 SEAT CUSHION COVER SUB-ASSEMBLY LH
| *a | Fastener |
| *b | Hog Ring Pliers |
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
35.INSTALL SEAT CUSHION COVER WITH PAD
Attach the 2 hooks to install the seat cushion cover with pad.
Close the seat cushion cover under part with the 2 clips.
Close the 2 fasteners.
71827B
36.INSTALL REAR NO. 1 SEAT CUSHION MOULDING
Attach the 4 guides and 2 claws to install the moulding.
install the 2 clips.
71693
37.INSTALL REAR SEAT LOWER CUSHION HINGE COVER RH
Attach the guide and 2 claws to install the cover.
Install the 2 screws.
71693
38.INSTALL REAR SEAT LOWER CUSHION HINGE COVER LH
Attach the 3 claws to install the cover.
Install the 2 screws.
73949
39.INSTALL CAP
Install the 2 caps.
71970
40.INSTALL REAR SEAT HEADREST ASSEMBLY
Install the headrest.