Home › Vehicle Interior › SEAT › SEAT HEATER SYSTEM › from 2021.06
RM27T0E _58 Vehicle Interior _053737 SEAT _0261113 SEAT HEATER SYSTEM G

SEAT  SEAT HEATER SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 87501B 1.INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY LH (for Front Side)

a.
U148048E03
1.615,1.375 1.615,1.781 false 2.042,1.375 2.042,1.781 false 1.333,1.063 0.948,1.063 false 1.656,0.323 1.833,0.469 0.177,0.146 10 false b7 0.563,1 0.917,1.167 0.354,0.167 10 false SWL 2.01,1.844 2.135,2.031 0.125,0.188 10 false E 1.573,1.833 1.698,2 0.125,0.167 10 false B 0.135,0.083 0.313,0.26 0.177,0.177 10 false *a

Disconnect the seat heater control sub-assembly LH (for Front Side) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b7-6 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
b7-1 (SWL) - b7-6 (E) Ignition switch ON, seat heater switch LH off Below 1 V
Ignition switch ON, seat heater switch LH on 11 to 14 V
b7-4 (B) - b7-6 (E) Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Seat Heater Control Sub-assembly LH [for Front Side])

If the result is not as specified, there may be a malfunction on the wire harness side.


d.

Connect the seat heater control sub-assembly LH (for Front Side) connector.


e.
U148028E01
0.944,1.831 1.235,1.985 0.292,0.154 10 THL 0.63,1.217 0.809,1.372 0.180,0.155 10 b7 1.113,1.812 1.113,1.712 1.113,1.712 1.578,1.475 false 0.143,0.108 0.335,0.283 0.192,0.175 10 *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
b7-5 (THL) - Body ground Ignition switch ON, seat heater switch LH on, MIN → MAX Gradual increase between value below 1 V and value from 11 to 14 V


Text in Illustration
*a Component with harness connected
(Seat Heater Control Sub-assembly LH [for Front Side])

If the result is not as specified, the seat seat heater control sub-assembly LH (for Front Side) may have a malfunction.


Hide 87501A 2.INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY RH (for Front Side)

a.
U148049E03
1.615,1.365 1.615,1.771 false 2.042,1.365 2.042,1.771 false 1.313,1.052 0.938,1.052 false 1.635,0.323 1.833,0.469 0.198,0.146 10 false a7 0.521,0.969 0.875,1.135 0.354,0.167 10 false SWR 2.021,1.781 2.146,1.969 0.125,0.188 10 false E 1.531,1.781 1.719,1.948 0.188,0.167 10 false B1 0.135,0.083 0.313,0.26 0.177,0.177 10 false *a

Disconnect the seat heater control sub-assembly RH (for Front Side) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a7-6 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
a7-1 (SWR) - a7-6 (E) Ignition switch ON, seat heater switch RH off Below 1 V
Ignition switch ON, seat heater switch RH on 11 to 14 V
a7-4 (B1) - a7-6 (E) Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Seat Heater Control Sub-assembly RH [for Front Side])

If the result is not as specified, there may be a malfunction on the wire harness side.


d.

Connect the seat heater control sub-assembly RH (for Front Side) connector.


e.
U148029E01
0.944,1.831 1.258,1.985 0.315,0.154 10 THR 0.63,1.222 0.810,1.377 0.180,0.155 10 a7 1.113,1.812 1.113,1.712 1.113,1.712 1.578,1.475 false 0.143,0.108 0.335,0.283 0.192,0.175 10 *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
a7-5 (THR) - Body ground Ignition switch ON, seat heater switch RH on, MIN → MAX Gradual increase between value below 1 V and value from 11 to 14 V


Text in Illustration
*a Component with harness connected
(Seat Heater Control Sub-assembly RH [for Front Side])

If the result is not as specified, the seat seat heater control sub-assembly RH (for Front Side) may have a malfunction.


Hide 87501D 3.INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY LH (for Rear Side) (w/ Rear Seat Heater System)

a.
B620386N01
1.469,0.115 1.885,0.333 0.417,0.219 0.667,0.615 0.917,0.615 0.917,0.615 1.229,0.885 true 1.083,1.854 1.333,1.854 1.333,1.854 1.51,1.469 true 2.667,1.833 2.417,1.833 2.417,1.833 2.198,1.458 true 1.604,0.135 1.917,0.333 0.313,0.198 10 false x2 0.938,1.771 1.25,1.969 0.313,0.198 10 false B 2.719,1.75 3.031,1.948 0.313,0.198 10 false E 0.292,0.5 0.76,0.708 0.469,0.208 10 false SWL 0.094,0.073 0.563,0.281 0.469,0.208 10 false *a

Disconnect the seat heater control sub-assembly LH (for Rear Side) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
x2-6 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
x2-1 (SWL) - x2-6 (E) Ignition switch ON, seat heater switch LH off Below 1 V
Ignition switch ON, seat heater switch LH on 11 to 14 V
x2-4 (B) - x2-6 (E) Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Seat Heater Control Sub-assembly LH [for Rear Side])

If the result is not as specified, there may be a malfunction on the wire harness side.


d.

Connect the seat heater control sub-assembly LH (for Rear Side) connector.


e.
U148030N01
1.115,1.813 1.115,1.708 1.115,1.708 1.573,1.479 false 0.948,1.833 1.24,1.99 0.292,0.156 10 false THL 0.635,1.208 0.813,1.365 0.177,0.156 10 false x2 0.146,0.104 0.333,0.281 0.188,0.177 10 false *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
x1-5 (THL) - Body ground Ignition switch ON, seat heater switch LH on, MIN → MAX Gradual increase between value below 1 V and value from 11 to 14 V


Text in Illustration
*a Component with harness connected
(Seat Heater Control Sub-assembly LH [for Rear Side])

If the result is not as specified, the seat seat heater control sub-assembly LH (for Rear Side) may have a malfunction.


Hide 87501D 4.INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY RH (for Rear Side) (w/ Rear Seat Heater System)

a.
B620386N02
1.469,0.115 1.885,0.333 0.417,0.219 0.667,0.615 0.917,0.615 0.917,0.615 1.229,0.885 true 1.083,1.854 1.333,1.854 1.333,1.854 1.51,1.469 true 2.667,1.833 2.417,1.833 2.417,1.833 2.198,1.458 true 1.604,0.135 1.917,0.333 0.313,0.198 10 false w3 0.938,1.771 1.25,1.969 0.313,0.198 10 false B 2.719,1.75 3.031,1.948 0.313,0.198 10 false E 0.292,0.531 0.76,0.74 0.469,0.208 10 false SWR 0.094,0.073 0.563,0.281 0.469,0.208 10 false *a

Disconnect the seat heater control sub-assembly RH (for Rear Side) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
w3-6 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
w3-1 (PWR) - w3-6 (E) Ignition switch ON, seat heater switch RH off Below 1 V
Ignition switch ON, seat heater switch RH on 11 to 14 V
w3-4 (B) - w3-6 (E) Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Seat Heater Control Sub-assembly RH [for Rear Side])

If the result is not as specified, there may be a malfunction on the wire harness side.


d.

Connect the seat heater control sub-assembly RH (for Rear Side) connector.


e.
U169772N01
1.115,1.813 1.115,1.708 1.115,1.708 1.573,1.479 false 0.948,1.833 1.24,1.99 0.292,0.156 10 false THL 0.635,1.229 0.917,1.438 0.281,0.208 10 false w3 0.146,0.104 0.333,0.281 0.188,0.177 10 false *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
w3-5 (THR) - Body ground Ignition switch ON, seat heater switch RH on, MIN → MAX Gradual increase between value below 1 V and value from 11 to 14 V


Text in Illustration
*a Component with harness connected
(Seat Heater Control Sub-assembly RH [for Rear Side])

If the result is not as specified, the seat seat heater control sub-assembly RH (for Rear Side) may have a malfunction.