TERMINALS OF ECM
System information · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


Measure the voltage according to the value(s) in the table below.
- HINT:
- The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated.
- The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the Specified Condition column.
- The illustration above can be used as a reference to identify the ECM terminal locations.
| Terminal No. (Symbol) |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
| A38*1-20 (BATT) - C45*1-81 (E1) A52*2-20 (BATT) - C46*2-81 (E1) |
L - BR |
Battery (for measuring the battery voltage and for the ECM memory) |
Always |
11 to 14 V |
| A38*1-3 (+BM) - C45*1-81 (E1) A52*2-3 (+BM) - C46*2-81 (E1) |
P-B - BR |
Power source of throttle actuator |
Always |
11 to 14 V |
| A38*1-28 (IGSW) - C45*1-81 (E1) A52*2-28 (IGSW) - C46*2-81 (E1) |
B - BR |
Ignition switch |
Ignition switch ON |
11 to 14 V |
| A38*1-2 (+B) - C45*1-81 (E1) A52*2-2 (+B) - C46*2-81 (E1) |
B - BR |
Power source of ECM |
Ignition switch ON |
11 to 14 V |
| A38*1-1 (+B2) - C45*1-81 (E1) A52*2-1 (+B2) - C46*2-81 (E1) |
B - BR |
Power source of ECM |
Ignition switch ON |
11 to 14 V |
| C45*1-58 (OC1+) - C45*1-57 (OC1-) C46*2-58 (OC1+) - C46*2-57 (OC1-) |
L-B - R-B |
Camshaft timing oil control valve (OCV) (bank 1) |
Ignition switch ON |
Pulse generation (See waveform 1) |
| C45*1-52 (OC2+) - C45*1-51 (OC2-) C46*2-52 (OC2+) - C46*2-51 (OC2-) |
B - B-L |
Camshaft timing oil control valve (OCV) (bank 2) |
Ignition switch ON |
Pulse generation (See waveform 1) |
| A38*1-44 (MREL) - C45*1-81 (E1) A52*2-44 (MREL) - C46*2-81 (E1) |
W-R - BR |
EFI relay |
Ignition switch ON |
11 to 14 V |
| C45*1-115 (VCV1) - C45*1-78 (ETHW) C46*2-115 (VCV1) - C46*2-78 (ETHW) |
L - BR |
Power source of sensor (specific voltage) |
Ignition switch ON |
4.5 to 5.5 V |
| C45*1-113 (VCV2) - C45*1-74 (ETHA) C46*2-113 (VCV2) - C46*2-74 (ETHA) |
L - BR |
Power source of sensor (specific voltage) |
Ignition switch ON |
4.5 to 5.5 V |
| C45*1-72 (VG) - C45*1-73 (E2G) C46*2-72 (VG) - C46*2-73 (E2G) |
L-Y - G-W |
Mass air flow meter |
Idling, shift lever in P or N, A/C switch off |
0.5 to 3.0 V |
| C45*1-71 (THA) - C45*1-74 (ETHA) C46*2-71 (THA) - C46*2-74 (ETHA) |
Y-B - BR |
Intake air temperature sensor |
Idling, intake air temperature 20°C (68°F) |
0.5 to 3.4 V |
| C45*1-79 (THW) - C45*1-78 (ETHW) C46*2-79 (THW) - C46*2-78 (ETHW) |
G-B - BR |
Engine coolant temperature sensor |
Idling, engine coolant temperature 80°C (176°F) |
0.2 to 1.0 V |
| C45*1-96 (VCTA) - C45*1-97 (ETA) C46*2-96 (VCTA) - C46*2-97 (ETA) |
L - B |
Power source of throttle position sensor (specific voltage) |
Ignition switch ON |
4.5 to 5.5 V |
| C45*1-98 (VTA1) - C45*1-97 (ETA) C46*2-98 (VTA1) - C46*2-97 (ETA) |
R-Y - B |
Throttle position sensor (for engine control) |
Ignition switch ON, throttle valve fully closed |
0.5 to 1.1 V |
| Ignition switch ON, throttle valve fully open |
3.2 to 4.8 V |
|||
| C45*1-99 (VTA2) - C45*1-97 (ETA) C46*2-99 (VTA2) - C46*2-97 (ETA) |
Y-B - B |
Throttle position sensor (for sensor malfunction detection) |
Ignition switch ON, throttle valve fully closed |
2.1 to 3.1 V |
| Ignition switch ON, throttle valve fully open |
4.6 to 5.0 V |
|||
| A38*1-55 (VPA) - A38*1-59 (EPA) A52*2-55 (VPA) - A52*2-59 (EPA) |
R - W-L |
Accelerator pedal position sensor (for engine control) |
Ignition switch ON, accelerator pedal fully released |
0.5 to 1.1 V |
| Ignition switch ON, accelerator pedal fully depressed |
2.6 to 4.5 V |
|||
| A38*1-56 (VPA2) - A38*1-60 (EPA2) A52*2-56 (VPA2) - A52*2-60 (EPA2) |
GR-G - BR |
Accelerator pedal position sensor (for sensor malfunction detection) |
Ignition switch ON, accelerator pedal fully released |
1.2 to 2.0 V |
| Ignition switch ON, accelerator pedal fully depressed |
3.4 to 5.0 V |
|||
| A38*1-57 (VCPA) - A38*1-59 (EPA) A52*2-57 (VCPA) - A52*2-59 (EPA) |
L-W - W-L |
Power source of accelerator pedal position sensor (for VPA) |
Ignition switch ON |
4.5 to 5.5 V |
| A38*1-58 (VCP2) - A38*1-60 (EPA2) A52*2-58 (VCP2) - A52*2-60 (EPA2) |
V - BR |
Power source of accelerator pedal position sensor (for VPA2) |
Ignition switch ON |
4.5 to 5.5 V |
| C45*1-86 (HA1A) - C45*1-23 (E04) C46*2-86 (HA1A) - C46*2-23 (E04) |
L-R - W-B |
Air fuel ratio (A/F) sensor heater |
Idling |
Below 3.0 V |
| C45*1-109 (HA2A) - C45*1-46 (E05) C46*2-109 (HA2A) - C46*2-46 (E05) |
G - W-B |
Ignition switch ON |
11 to 14 V |
|
| C45*1-93 (A1A+) - C45*1-81 (E1) C46*2-93 (A1A+) - C46*2-81 (E1) |
G - BR |
A/F sensor |
Ignition switch ON |
3.3 V*3 |
| C45*1-120 (A2A+) - C45*1-81 (E1) C46*2-120 (A2A+) - C46*2-81 (E1) |
V - BR |
A/F sensor |
Ignition switch ON |
3.3 V*3 |
| C45*1-116 (A1A-) - C45*1-81 (E1) C46*2-116 (A1A-) - C46*2-81 (E1) |
R - BR |
A/F sensor |
Ignition switch ON |
2.9 V*3 |
| C45*1-119 (A2A-) - C45*1-81 (E1) C46*2-119 (A2A-) - C46*2-81 (E1) |
P - BR |
A/F sensor |
Ignition switch ON |
2.9 V*3 |
| C45*1-48 (HT1B) - C45*1-104 (E03) C46*2-48 (HT1B) - C46*2-104 (E03) |
G - BR |
Heated oxygen sensor heater |
Idling |
Below 3.0 V |
| C45*1-47 (HT2B) - C45*1-104 (E03) C46*2-47 (HT2B) - C46*2-104 (E03) |
B - BR |
Ignition switch ON |
11 to 14 V |
|
| C45*1-88 (OX1B) - C45*1-65 (EX1B) C46*2-88 (OX1B) - C46*2-65 (EX1B) |
W - BR |
Heated oxygen sensor |
Engine speed maintained at 2500 rpm for 2 minutes after warming up engine |
Pulse generation (See waveform 2) |
| C45*1-87 (OX2B) - C45*1-64 (EX2B) C46*2-87 (OX2B) - C46*2-64 (EX2B) |
B - BR |
|||
| C45*1-45 (#10) - C45*1-22 (E01) C46*2-45 (#10) - C46*2-22 (E01) |
R-L - W-B |
Fuel injector |
Ignition switch ON |
11 to 14 V |
| C45*1-85 (#20) - C45*1-22 (E01) C46*2-85 (#20) - C46*2-22 (E01) |
L - W-B |
|||
| C45*1-44 (#30) - C45*1-22 (E01) C46*2-44 (#30) - C46*2-22 (E01) |
R-B - W-B |
|||
| C45*1-84 (#40) - C45*1-22 (E01) C46*2-84 (#40) - C46*2-22 (E01) |
Y - W-B |
Idling |
Pulse generation (See waveform 3) |
|
| C45*1-43 (#50) - C45*1-22 (E01) C46*2-43 (#50) - C46*2-22 (E01) |
G - W-B |
|||
| C45*1-83 (#60) - C45*1-22 (E01) C46*2-83 (#60) - C46*2-22 (E01) |
R - W-B |
|||
| C45*1-95 (KNK1) - C45*1-94 (EKNK) C46*2-95 (KNK1) - C46*2-94 (EKNK) |
G - R |
Knock sensor (bank 1) |
Engine speed maintained at 4000 rpm after warming up engine |
Pulse generation (See waveform 4) |
| C45*1-118 (KNK2) - C45*1-117 (EKN2) C46*2-118 (KNK2) - C46*2-117 (EKN2) |
W - B |
Knock sensor (bank 2) |
Engine speed maintained at 4000 rpm after warming up engine |
Pulse generation (See waveform 4) |
| C45*1-69 (VV1+) - C45*1-92 (VV1-) C46*2-69 (VV1+) - C46*2-92 (VV1-) |
R - L-R |
Variable Valve Timing (VVT) sensor (bank 1) |
Idling |
Pulse generation (See waveform 5) |
| C45*1-67 (VV2+) - C45*1-90 (VV2-) C46*2-67 (VV2+) - C46*2-90 (VV2-) |
R - G |
Variable Valve Timing (VVT) sensor (bank 2) |
Idling |
Pulse generation (See waveform 5) |
| C45*1-110 (NE+) - C45*1-111 (NE-) C46*2-110 (NE+) - C46*2-111 (NE-) |
B - W |
Crankshaft position sensor |
Idling |
Pulse generation (See waveform 5) |
| C45*1-40 (IGT1) - C45*1-81 (E1) C46*2-40 (IGT1) - C46*2-81 (E1) |
B-R - BR |
Ignition coil (ignition signal) |
Idling |
Pulse generation (See waveform 6) |
| C45*1-39 (IGT2) - C45*1-81 (E1) C46*2-39 (IGT2) - C46*2-81 (E1) |
L-B - BR |
|||
| C45*1-38 (IGT3) - C45*1-81 (E1) C46*2-38 (IGT3) - C46*2-81 (E1) |
B - BR |
|||
| C45*1-37 (IGT4) - C45*1-81 (E1) C46*2-37 (IGT4) - C46*2-81 (E1) |
L-B - BR |
|||
| C45*1-36 (IGT5) - C45*1-81 (E1) C46*2-36 (IGT5) - C46*2-81 (E1) |
G-R - BR |
|||
| C45*1-35 (IGT6) - C45*1-81 (E1) C46*2-35 (IGT6) - C46*2-81 (E1) |
G - BR |
|||
| C45*1-106 (IGF1) - C45*1-81 (E1) C46*2-106 (IGF1) - C46*2-81 (E1) |
G-B - BR |
Ignition coil (ignition confirmation signal) |
Ignition switch ON |
4.5 to 5.5 V |
| Idling |
Pulse generation (See waveform 6) |
|||
| C45*1-108 (PRG) - C45*1-81 (E1) C46*2-108 (PRG) - C46*2-81 (E1) |
L-B - BR |
Purge VSV |
Ignition switch ON |
11 to 14 V |
| Idling |
Pulse generation (See waveform 7) |
|||
| A38*1-8 (SPD) - C45*1-81 (E1) A52*2-8 (SPD) - C46*2-81 (E1) |
V-R - BR |
Speed signal from combination meter |
Ignition switch ON, wheel rotated slowly |
Pulse generation (See waveform 8) |
| A38*1-48 (STA) - C45*1-81 (E1) A52*2-48 (STA) - C46*2-81 (E1) |
R-B - BR |
Starter signal |
Cranking |
11 to 14 V |
| A38*1-36 (STP) - C45*1-81 (E1) A52*2-36 (STP) - C46*2-81 (E1) |
R - BR |
Stop light switch |
Brake pedal depressed |
7.5 to 14 V |
| Brake pedal released |
Below 1.5 V |
|||
| A38*1-35 (ST1-) - C45*1-81 (E1) A52*2-35 (ST1-) - C46*2-81 (E1) |
R-W - BR |
Stop light switch (opposite to STP terminal) |
Ignition switch ON, brake pedal depressed |
Below 1.5 V |
| Ignition switch ON, brake pedal released |
7.5 to 14 V |
|||
| C45*1-62 (NSW) - C45*1-81 (E1) C46*2-62 (NSW) - C46*2-81 (E1) |
L - BR |
Park/neutral position switch |
Ignition switch ON, shift lever in P or N |
Below 3.0 V |
| Ignition switch ON, shift lever in other than P or N |
11 to 14 V |
|||
| C45*1-19 (M+) - C45*1-20 (ME01) C46*2-19 (M+) - C46*2-20 (ME01) |
R - W-B |
Throttle actuator |
Idling with warm engine |
Pulse generation (See waveform 9) |
| C45*1-18 (M-) - C45*1-20 (ME01) C46*2-18 (M-) - C46*2-20 (ME01) |
G - W-B |
Throttle actuator |
Idling with warm engine |
Pulse generation (See waveform 10) |
| A38*1-7 (FC) - C45*1-81 (E1) A52*2-7 (FC) - C46*2-81 (E1) |
L-R - BR |
Fuel pump control |
Ignition switch ON |
11 to 14 V |
| A38*1-24 (W) - C46*2-81 (E1) A52*2-24 (W) - C46*2-81 (E1) |
R-Y - BR |
MIL |
Ignition switch ON |
Below 3.0 V |
| Idling |
11 to 14 V |
|||
| A38*1-27 (TC) - C45*1-81 (E1) A52*2-27 (TC) - C46*2-81 (E1) |
V-W - BR |
Terminal TC of DLC3 |
Ignition switch ON |
11 to 14 V |
| A38*1-15 (TACH) - C45*1-81 (E1) A52*2-15 (TACH) - C46*2-81 (E1) |
W-G - BR |
Engine speed |
Idling |
Pulse generation (See waveform 11) |
| C45*1-107 (ACIS) - C45*1-81 (E1) C46*2-107 (ACIS) - C46*2-81 (E1) |
R-W - BR |
VSV for ACIS |
Ignition switch ON |
11 to 14 V |
| C45*1-70 (PSW) - C45*1-81 (E1) C46*2-70 (PSW) - C46*2-81 (E1) |
L - BR |
P/S pressure switch |
Ignition switch ON |
11 to 14 V |
| A38*1-41 (CANH) - C45*1-81 (E1) A52*2-41 (CANH) - C46*2-81 (E1) |
P - BR |
CAN communication line |
Ignition switch ON |
Pulse generation (See waveform 12) |
| A38*1-49 (CANL) - C45*1-81 (E1) A52*2-49 (CANL) - C46*2-81 (E1) |
B - BR |
CAN communication line |
Ignition switch ON |
Pulse generation (See waveform 13) |
| C45*1-59 (FPC) - C45*1-81 (E1) C46*2-59 (FPC) - C46*2-81 (E1) |
W-G - BR |
Fuel pump control |
Ignition switch ON |
11 to 14 V |
| A38*1-19 (DI) - C45*1-81 (E1) A52*2-19 (DI) - C46*2-81 (E1) |
G-Y - BR |
Fuel pump control |
Ignition switch ON |
0 to 3.0 V |
| A38*1-14 (STSW) - C45*1-81 (E1) A52*2-14 (STSW) - C46*2-81 (E1) |
R - BR |
Ignition switch signal |
Shift lever in P or N, engine cranking |
6.0 V or more |
| A38*1-13 (ACCR) - C45*1-81 (E1) A52*2-13 (ACCR) - C46*2-81 (E1) |
L-Y - BR |
ACC (accessory) relay control signal |
Cranking |
Below 1.5 V |
| C45*1-63 (STAR) - C45*1-81 (E1) C46*2-63 (STAR) - C46*2-81 (E1) |
L - BR |
Starter relay control |
Ignition switch ON |
Below 1.5 V |
| Cranking |
6.0 V or more |
- HINT:
- *1: for LHD
- *2: for RHD
- *3: The ECM terminal voltage is constant regardless of the output voltage from the sensor.
- *1: for LHD
| WAVEFORM 1 |
![]() ![]() |
| ECM Terminal Name |
Between OC1+ and OC1- or OC2+ and OC2- |
| Tester Range |
5 V/DIV., 1 msec./DIV., |
| Condition |
Idling |
| WAVEFORM 2 |
![]() ![]() |
| ECM Terminal Name |
Between OX1B and EX1B or OX2B and EX2B |
| Tester Range |
0.2 V/DIV., 200 msec./DIV. |
| Condition |
Engine speed maintained at 2500 rpm for 2 minutes after warming up engine |
- HINT:
- In the Data List, item O2S B1S2 or O2S B2S2 shows the ECM input values from the heated oxygen sensor.
| WAVEFORM 3 |
![]() ![]() |
| ECM Terminal Name |
Between #10 (to #60) and E01 |
| Tester Range |
30 V/DIV., 20 msec./DIV. |
| Condition |
Idling |
- HINT:
- The wavelength becomes shorter as the engine speed increases.
| WAVEFORM 4 |
![]() ![]() |
| ECM Terminal Name |
Between KNK1 and EKNK or KNK2 and EKN2 |
| Tester Range |
1 V/DIV., 0.01 to 1 msec./DIV. |
| Condition |
Engine speed maintained at 4000 rpm after warming up engine |
- HINT:
- The wavelength becomes shorter as the engine speed increases.
- The waveforms and amplitudes displayed on the tester differ slightly depending on the vehicle.
- The wavelength becomes shorter as the engine speed increases.
| WAVEFORM 5 |
![]() ![]() |
Crankshaft position sensor
VVT sensor
ECM Terminal Name
(a) Between NE+ and NE-
(b) Between VV1+ and VV1- or VV2+ and VV2-
Tester Range
2 V/DIV., 20 msec./DIV.
Condition
Idling
- HINT:
- The wavelength becomes shorter as the engine speed increases.
| WAVEFORM 6 |
![]() ![]() |
Igniter IGT signal (from ECM to igniter)
Igniter IGF signal (from igniter to ECM)
ECM Terminal Name
(a) Between IGT (1 to 6) and E1
(b) Between IGF1 and E1
Tester Range
2 V/DIV., 20 msec./DIV.
Condition
Idling
- HINT:
- The wavelength becomes shorter as the engine speed increases.
| WAVEFORM 7 |
![]() ![]() |
| ECM Terminal Name |
Between PRG and E1 |
| Tester Range |
10 V/DIV., 10 to 100 msec./DIV. |
| Condition |
Idling |
- HINT:
- If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.
| WAVEFORM 8 |
![]() ![]() |
| ECM Terminal Name |
Between SPD and E1 |
| Tester Range |
2 V/DIV., 20 msec./DIV. |
| Condition |
Ignition switch ON, wheel rotated slowly |
- HINT:
- The wavelength becomes shorter as the vehicle speed increases.
| WAVEFORM 9 |
![]() ![]() |
| ECM Terminal Name |
Between M+ and ME01 |
| Tester Range |
5 V/DIV., 1 msec./DIV. |
| Condition |
Idling with warm engine |
- HINT:
- The duty ratio varies depending on the throttle actuator operation.
| WAVEFORM 10 |
![]() ![]() |
| ECM Terminal Name |
Between M- and ME01 |
| Tester Range |
5 V/DIV., 1 msec./DIV. |
| Condition |
Idling with warm engine |
- HINT:
- The duty ratio varies depending on the throttle actuator operation.
| WAVEFORM 11 |
![]() ![]() |
| ECM Terminal Name |
Between TACH and E1 |
| Tester Range |
5 V/DIV., 10 msec./DIV. |
| Condition |
Idling |
- HINT:
- The wavelength becomes shorter as the engine speed increases.
| WAVEFORM 12 |
![]() ![]() |
| ECM Terminal Name |
Between CANH and E1 |
| Tester Range |
1 V/DIV., 10 μsec./DIV. |
| Condition |
Ignition switch ON |
- HINT:
- The wavelength varies depending on the CAN communication signal.
| WAVEFORM 13 |
![]() ![]() |
| ECM Terminal Name |
Between CANL and E1 |
| Tester Range |
1 V/DIV., 10 μsec./DIV. |
| Condition |
Ignition switch ON |
- HINT:
- The wavelength varies depending on the CAN communication signal.












