2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

TERMINALS OF ECM

System information · Vehicles built Sep 2011 – Dec 2011


CHECK ECM
A179454E04
  1. Measure the voltage according to the value(s) in the table below.

    HINT:
    The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A38-1 (BATT) - C45-81 (E1)*1
    A52-1 (BATT) - C46-81 (E1)*2
    L - BR
    Battery (for measuring battery voltage and for ECM memory)
    Always
    11 to 14 V
    C45-41 (+BM) - C45-81 (E1)*1
    C46-41 (+BM) - C46-81 (E1)*2
    P - BR
    Power source of throttle actuator
    Always
    11 to 14 V
    A38-28 (IGSW) - C45-81 (E1)*1
    A52-28 (IGSW) - C46-81 (E1)*2
    B - BR
    Engine switch
    Engine switch on (IG)
    11 to 14 V
    A38-3 (+B) - C45-81 (E1)*1
    A52-3 (+B) - C46-81 (E1)*2
    B - BR
    Power source of ECM
    Engine switch on (IG)
    11 to 14 V
    A38-2 (+B2) - C45-81 (E1)*1
    A52-2 (+B2) - C46-81 (E1)*2
    B - BR
    Power source of ECM
    Engine switch on (IG)
    11 to 14 V
    C45-58 (OC1+) - C45-57 (OC1-)*1
    C46-58 (OC1+) - C46-57 (OC1-)*2
    B - B-L
    Cam Timing oil control valve (OCV) (for Bank 1)
    Engine switch on (IG)
    Pulse generation
    (see waveform 1)
    C45-52 (OC2+) - C45-51 (OC2-)*1
    C46-52 (OC2+) - C46-51 (OC2-)*2
    L-B - R-B
    Cam Timing oil control valve (OCV) (for Bank 2)
    Engine switch on (IG)
    Pulse generation
    (see waveform 1)
    A38-34 (MREL) - C45-81 (E1)*1
    A52-34 (MREL) - C46-81 (E1)*2
    L - BR
    EFI relay
    Engine switch on (IG)
    11 to 14 V
    C45-74 (VG) - C45-75 (E2G)*1
    C46-74 (VG) - C46-75 (E2G)*2
    L-Y - G-W
    Mass air flow meter
    Idling, shift lever in P or N, A/C switch off
    0.5 to 3.0 V
    C45-73 (THA) - C45-97 (ETHW)*1
    C46-73 (THA) - C46-97 (ETHW)*2
    Y-B - BR
    Intake air temperature sensor
    Idling, intake air temperature 20°C (68°F)
    0.5 to 3.4 V
    C45-76 (THW) - C45-97 (ETHW)*1
    C46-76 (THW) - C46-97 (ETHW)*2
    G-B - BR
    Engine coolant temperature sensor
    Idling, engine coolant temperature 80°C (176°F)
    0.2 to 1.0 V
    C45-80 (VCTA) - C45-79 (ETA)*1
    C46-80 (VCTA) - C46-79 (ETA)*2
    L - Y
    Power source of throttle position sensor (specific voltage)
    Engine switch on (IG)
    4.5 to 5.5 V
    C45-78 (VTA1) - C45-79 (ETA)*1
    C46-78 (VTA1) - C46-79 (ETA)*2
    R-Y - Y
    Throttle position sensor (for engine control)
    Engine switch on (IG),
    throttle valve fully closed
    0.5 to 1.2 V
    Engine switch on (IG),
    throttle valve fully open
    3.2 to 4.8 V
    C45-77 (VTA2) - C45-79 (ETA)*1
    C46-77 (VTA2) - C46-79 (ETA)*2
    Y-B - Y
    Throttle position sensor (for sensor malfunction detection)
    Engine switch on (IG),
    throttle valve fully closed
    2.1 to 3.1 V
    Engine switch on (IG),
    throttle valve fully open
    4.5 to 5.5 V
    A38-55 (VPA) - A38-58 (EPA)*1
    A52-55 (VPA) - A52-58 (EPA)*2
    R - W-L
    Accelerator pedal position sensor (for engine control)
    Engine switch on (IG),
    accelerator pedal released
    0.5 to 1.1 V
    Engine switch on (IG),
    accelerator pedal fully depressed
    2.6 to 4.5 V
    A38-56 (VPA2) - A38-60 (EPA2)*1
    A52-56 (VPA2) - A52-60 (EPA2)*2
    GR-G - BR
    Accelerator pedal position sensor (for sensor malfunctioning detection)
    Engine switch on (IG),
    accelerator pedal released
    1.2 to 2.0 V
    Engine switch on (IG),
    accelerator pedal fully depressed
    3.4 to 5.3 V
    A38-57 (VCPA) - A38-58 (EPA)*1
    A52-57 (VCPA) - A52-58 (EPA)*2
    L-W - W-L
    Power source of accelerator pedal position sensor (for VPA)
    Engine switch on (IG)
    4.5 to 5.5 V
    A38-59 (VCP2) - A38-60 (EPA2)*1
    A52-59 (VCP2) - A52-60 (EPA2)*2
    V - BR
    Power source of accelerator pedal position sensor (for VPA2)
    Engine switch on (IG)
    4.5 to 5.5 V
    C45-22 (HA1A) - C45-23 (E04)*1
    C46-22 (HA1A) - C46-23 (E04)*2
    L - W-B
    A/F sensor heater
    Idling
    Below 3.0 V
    Engine switch on (IG)
    11 to 14 V
    C45-20 (HA2A) - C45-21 (E05)*1
    C46-20 (HA2A) - C46-21 (E05)*2
    G - W-B
    A/F sensor heater
    Idling
    Below 3.0 V
    Engine switch on (IG)
    11 to 14 V
    C45-126 (A1A+) - C45-81 (E1)*1
    C46-126 (A1A+) - C46-81 (E1)*2
    G -BR
    A/F sensor
    Engine switch on (IG)
    3.3 V
    C45-125 (A1A-) - C45-81 (E1)*1
    C46-125 (A1A-) - C46-81 (E1)*2
    R - BR
    A/F sensor
    Engine switch on (IG)
    2.9 V
    C45-103 (A2A+) - C45-81 (E1)*1
    C46-103 (A2A+) - C46-81 (E1)*2
    P - BR
    A/F sensor
    Engine switch on (IG)
    3.3 V
    C45-102 (A2A-) - C45-81 (E1)*1
    C46-102 (A2A-) - C46-81 (E1)*2
    L - BR
    A/F sensor
    Engine switch on (IG)
    2.9 V
    C45-45 (HT1B) - C45-46 (E03)*1
    C46-45 (HT1B) - C46-46 (E03)*2
    G-B - W-B
    Heated oxygen sensor heater
    Idling
    Below 3.0 V
    Engine switch on (IG)
    11 to 14 V
    C45-44 (HT2B) - C45-46 (E03)*1
    C46-44 (HT2B) - C46-46 (E03)*2
    B - W-B
    Heated oxygen sensor heater
    Idling
    Below 3.0 V
    Engine switch on (IG)
    11 to 14 V
    C45-114 (OX1B) - C45-115 (EX1B)*1
    C46-114 (OX1B) - C46-115 (EX1B)*2
    W - BR
    Heated oxygen sensor
    Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor
    Pulse generation
    (see waveform 2)
    C45-112 (OX2B) - C45-113 (EX2B)*1
    C46-112 (OX2B) - C46-113 (EX2B)*2
    B - BR
    C45-86 (#10) - C45-43 (E01)*1
    C46-86 (#10) - C46-43 (E01)*2
    R-L - W-B
    Fuel Injector
    Engine switch on (IG)
    11 to 14 V
    C45-109 (#20) - C45-43 (E01)*1
    C46-109 (#20) - C46-43 (E01)*2
    L - W-B
    C45-85 (#30) - C45-43 (E01)*1
    C46-85 (#30) - C46-43 (E01)*2
    R - W-B
    C45-108 (#40) - C45-43 (E01)*1
    C46-108 (#40) - C46-43 (E01)*2
    Y - W-B
    C45-84 (#50) - C45-43 (E01)*1
    C46-84 (#50) - C46-43 (E01)*2
    G - W-B
    Idling
    Pulse generation
    (see waveform 3)
    C45-107 (#60) - C45-43 (E01)*1
    C46-107 (#60) - C46-43 (E01)*2
    R - W-B
    C45-83 (#70) - C45-43 (E01)*1
    C46-83 (#70) - C46-43 (E01)*2
    W - W-B
    C45-106 (#80) - C45-43 (E01)*1
    C46-106 (#80) - C46-43 (E01)*2
    R-B - W-B
    C45-94 (KNK1) - C45-93 (EKNK)*1
    C46-94 (KNK1) - C46-93 (EKNK)*2
    G - R
    Knock sensor
    Engine speed maintained at 4000 rpm after warming up engine
    Pulse generation
    (see waveform 4)
    C45-117 (KNK2) - C45-116 (EKN2)*1
    C46-117 (KNK2) - C46-116 (EKN2)*2
    W - B
    C45-92 (VV1+) - C45-91 (VV1-)*1
    C46-92 (VV1+) - C46-91 (VV1-)*2
    R - G
    Variable valve timing (VVT) sensor (for intake side of bank 1)
    Idling
    Pulse generation
    (see waveform 5)
    C45-87 (VV2+) - C45-88 (VV2-)*1
    C46-87 (VV2+) - C46-88 (VV2-)*2
    R - W
    Variable valve timing (VVT) sensor (for intake side of bank 2)
    Idling
    Pulse generation
    (see waveform 5)
    C45-110 (NE+) - C45-111 (NE-)*1
    C46-110 (NE+) - C46-111 (NE-)*2
    L - G
    Crank position sensor
    Idling
    Pulse generation
    (see waveform 5)
    C45-40 (IGT1) - C45-81 (E1)*1
    C46-40 (IGT1) - C46-81 (E1)*2
    B-Y - BR
    Ignition coil (ignition signal)
    Idling
    Pulse generation
    (see waveform 6)
    C45-33 (IGT2) - C45-81 (E1)*1
    C46-33 (IGT2) - C46-81 (E1)*2
    L-Y - BR
    C45-37 (IGT3) - C45-81 (E1)*1
    C46-37 (IGT3) - C46-81 (E1)*2
    B - BR
    C45-38 (IGT4) - C45-81 (E1)*1
    C46-38 (IGT4) - C46-81 (E1)*2
    L-B - BR
    C45-35 (IGT5) - C45-81 (E1)*1
    C46-35 (IGT5) - C46-81 (E1)*2
    G-R - BR
    C45-36 (IGT6) - C45-81 (E1)*1
    C46-36 (IGT6) - C46-81 (E1)*2
    G - BR
    C45-34 (IGT7) - C45-81 (E1)*1
    C46-34 (IGT7) - C46-81 (E1)*2
    G-W - BR
    C45-39 (IGT8) - C45-81 (E1)*1
    C46-39 (IGT8) - C46-81 (E1)*2
    G-B - BR
    C45-104 (IGF1) - C45-81 (E1)*1
    C46-104 (IGF1) - C46-81 (E1)*2
    G-B - BR
    Ignition coil (ignition confirmation signal)
    Engine switch on (IG)
    4.5 to 5.5 V
    Idling
    Pulse generation
    (see waveform 6)
    C45-105 (IGF2) - C45-81 (E1)*1
    C46-105 (IGF2) - C46-81 (E1)*2
    R - BR
    Ignition coil (ignition confirmation signal)
    Engine switch on (IG)
    4.5 to 5.5 V
    Idling
    Pulse generation
    (see waveform 6)
    C45-63 (PRG) - C45-81 (E1)*1
    C46-63 (PRG) - C46-81 (E1)*2
    L-B - BR
    Purge VSV
    Engine switch on (IG)
    11 to 14 V
    Idling
    Pulse generation
    (see waveform 7)
    A38-13 (SPD) - C45-81 (E1)*1
    A52-13 (SPD) - C46-81 (E1)*2
    V-R - BR
    Speed signal from combination meter
    Driving at 20 km/h (12 mph)
    Pulse generation
    (see waveform 8)
    A38-46 (STA) - C45-81 (E1)*1
    A52-46 (STA) - C46-81 (E1)*2
    R-B - BR
    Starter signal
    Cranking
    5.5 V or higher
    C45-120 (NSW) - C45-81 (E1)*1
    C46-120 (NSW) - C46-81 (E1)*2
    L - BR
    Park/neutral position switch
    Engine switch on (IG), shift lever not in P or N
    11 to 14 V
    Engine switch on (IG), shift lever in P or N
    Below 3.0 V
    A38-36 (STP) - C45-81 (E1)*1
    A52-36 (STP) - C46-81 (E1)*2
    R - BR
    Stop light switch
    Brake pedal depressed
    7.5 to 14 V
    Brake pedal released
    Below 1.5 V
    A38-35 (ST1-) - C45-81 (E1)*1
    A52-35 (ST1-) - C46-81 (E1)*2
    R-W - BR
    Stop light switch
    (opposite to STP terminal)
    Engine switch on (IG),
    brake pedal depressed
    Below 1.5 V
    Engine switch on (IG),
    brake pedal released
    7.5 to 14 V
    C45-19 (M+) - C45-82 (ME01)*1
    C46-19 (M+) - C46-82 (ME01)*2
    R - W-B
    Throttle actuator
    Idling with warm engine
    Pulse generation
    (see waveform 9)
    C45-18 (M-) - C45-82 (ME01)*1
    C46-18 (M-) - C46-82 (ME01)*2
    G - W-B
    Throttle actuator
    Idling with warm engine
    Pulse generation
    (see waveform 10)
    A38-48 (FC) - C45-81 (E1)*1
    A52-48 (FC) - C46-81 (E1)*2
    L-R - BR
    Fuel pump control
    Engine switch on (IG)
    11 to 14 V
    A38-52 (FPC) - C45-81 (E1)*1
    A52-52 (FPC) - C46-81 (E1)*2
    W - BR
    Fuel pump control
    Engine switch on (IG)
    Below 1.5 V
    A38-24 (W) - C45-81 (E1)*1
    A52-24 (W) - C46-81 (E1)*2
    R-Y - BR
    MIL
    Engine switch on (IG)
    Below 3.0 V
    Idling
    11 to 14 V
    A38-16 (TC) - C45-81 (E1)*1
    A52-16 (TC) - C46-81 (E1)*2
    V-W - BR
    Terminal TC of DLC3
    Engine switch on (IG)
    11 to 14 V
    A38-15 (TACH) - C45-81 (E1)*1
    A52-15 (TACH) - C46-81 (E1)*2
    W-G - BR
    Engine speed
    Idling
    Pulse generation
    (see waveform 11)
    C45-66 (VC) - C45-97 (ETHW)*1
    C46-66 (VC) - C46-97 (ETHW)*2
    L - BR
    Power source for sensor (specific voltage)
    Engine switch on (IG)
    4.5 to 5.5 V
    C45-32 (ALT) - C45-81 (E1)*1
    C46-32 (ALT) - C46-81 (E1)*2
    R - BR
    Generator
    Engine switch on (IG)
    11 to 14 V
    A38-10 (CANH) - C45-81 (E1)*1
    A52-10 (CANH) - C46-81 (E1)*2
    P - BR
    CAN communication line
    Engine switch on (IG)
    Pulse generation
    (see waveform 12)
    A38-11 (CANL) - C45-81 (E1)*1
    A52-11 (CANL) - C46-81 (E1)*2
    B - BR
    CAN communication line
    Engine switch on (IG)
    Pulse generation
    (see waveform 13)
    C45-62 (ACIS) - C45-81 (E1)*1
    C46-62 (ACIS) - C46-81 (E1)*2
    R-W - BR
    VSV for ACIS (Acoustic Control Induction System) operation signal
    Engine switch on (IG)
    11 to 14 V
    C45-28 (AIRV) - C45-81 (E1)*1
    C46-28 (AIRV) - C46-81 (E1)*2
    BR - BR
    Air switching valve for secondary air injection system
    Engine switch on (IG)
    11 to 14 V
    C45-54 (AIRP) - C45-81 (E1)*1
    C46-54 (AIRP) - C46-81 (E1)*2
    P - BR
    Air pump control
    Engine switch on (IG)
    11 to 14 V
    C45-30 (AIDI) - C45-81 (E1)*1
    C46-30 (AIDI) - C46-81 (E1)*2
    G - BR
    Diagnostic information signal for air injection system
    Air injection system operates
    Pulse generation
    (see waveform 15)
    A38-54 (AIP) - C45-98 (ETHA)*1
    A52-54 (AIP) - C46-98 (ETHA)*2
    P-L - BR
    Secondary air injection system pressure signal
    Engine switch on (IG)
    3.0 to 3.6 V
    C45-90 (G2) - C45- 89 (G2-)*1
    C46-90 (G2) - C46- 89 (G2-)*2
    R - G
    Cam position sensor
    Idling
    Pulse generation
    (see waveform 14)
    A38-18 (DI) - C45-81 (E1)*1
    A52-18 (DI) - C46-81 (E1)*2
    G-Y - BR
    Fuel pump control
    Engine switch on (IG)
    0 to 3.0 V
    A38-14 (STSW) - C45-81 (E1)*1
    A52-14 (STSW) - C46-81 (E1)*2
    R - BR
    Starter switch
    Shift lever in P or N, cranking
    6.0 V or higher
    A38-41 (ACCR) - C45-81 (E1)*1
    A52-41 (ACCR) - C46-81 (E1)*2
    L-Y - BR
    ACC relay control signal
    Engine switch on (IG) → Cranking
    11 to 14 V → Below 1 V
    C45-16 (STAR) - C45-81 (E1)*1
    C46-16 (STAR) - C46-81 (E1)*2
    L - BR
    Starter relay control
    Engine switch on (IG)
    Below 1.5 V
    Cranking
    5.5 V or higher
    C45-72 (PSP) - C45-81 (E1)*1
    C46-72 (PSP) - C46-81 (E1)*2
    G - BR
    Power steering oil pressure sensor
    Engine switch on (IG)
    0.5 to 4.5 V

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  2. A093229E02
    WAVEFORM 1:
    Cam Timing Oil Control Valve (OCV) 
    Item
    Content
    Terminal No. (Symbol)
    Between OC1+ and OC1-
    Between OC2+ and OC2-
    Tool Setting
    5 V/DIV., 1 msec./DIV.
    Condition
    Idling

  3. A088863E05
    WAVEFORM 2:
    Heated Oxygen Sensor 
    Item
    Content
    Terminal No. (Symbol)
    Between OX1B and EX1B
    Between OX2B and EX2B
    Tool Setting
    0.2 V/DIV., 200 msec./DIV.
    Condition
    Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor

    HINT:
    In Data List, item O2S B1 S2 or O2S B2 S2 shows the ECM input values from the heated oxygen sensor.

  4. A093279E04
    WAVEFORM 3:
    Fuel Injector No. 1 (to No. 8) Injection Signal 
    Item
    Content
    Terminal No. (Symbol)
    Between #10 (to #80) and E01
    Tool Setting
    20 V/DIV., 20 msec./DIV.
    Condition
    Idling

    HINT:
    The wavelength becomes shorter as the engine speed increases.

  5. A085286E03
    WAVEFORM 4:
    Knock Sensor 
    Item
    Content
    Terminal No. (Symbol)
    Between KNK1 and EKNK
    Between KNK2 and EKN2
    Tool Setting
    1 V/DIV., 1 msec./DIV.
    Condition
    Engine speed maintained at 4000 rpm after warming up engine

    HINT:
    1. The wavelength becomes shorter as the engine speed increases.
    2. The waveforms and amplitudes displayed differ slightly depending on the vehicle.

  6. A164292E01
    WAVEFORM 5:
    Variable Valve Timing (VVT) Sensor (for Bank 1, 2) and Crankshaft Position Sensor 
    Item
    Content
    Terminal No. (Symbol)
    CH1: Between VV1+ and VV1-
    CH2: Between VV2+ and VV2-
    CH3: Between NE+ and NE-
    Tool Setting
    2 V/DIV., 20 msec./DIV.
    Condition
    Idling after engine warmed up

    HINT:
    The wavelength becomes shorter as engine speed increases.

  7. A093278E14
    WAVEFORM 6:
    Igniter IGT Signal (from ECM to Igniter) and Igniter IGF Signal (from Igniter to ECM) 
    Item
    Content
    Terminal No. (Symbol)
    (a) Between IGT1 (to IGT8) and E1
    (b) Between IGF1 (IGF2) and E1
    Tool Setting
    2 V/DIV., 20 msec./DIV.
    Condition
    Idling

    HINT:
    The wavelength becomes shorter as engine speed increases.

  8. A164291E01
    WAVEFORM 7:
    Purge VSV 
    Item
    Content
    Terminal No. (Symbol)
    Between PRG and E1
    Tool Setting
    10 V/DIV., 10 to 100 msec./DIV.
    Condition
    Idling

    HINT:
    If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.

  9. A093224E01
    WAVEFORM 8:
    Vehicle Speed Signal 
    Item
    Content
    Terminal No. (Symbol)
    Between SPD and E1
    Tool Setting
    2 V/DIV., 20 msec./DIV.
    Condition
    Driving at 20 km/h (12 mph)

    HINT:
    The wavelength becomes shorter as the vehicle speed increases.

  10. A093274E03
    WAVEFORM 9:
    Throttle Actuator Positive Terminal 
    Item
    Content
    Terminal No. (Symbol)
    Between M+ and ME01
    Tool Setting
    5 V/DIV., 1 msec./DIV.
    Condition
    Idling with warm engine

    HINT:
    The duty ratio varies depending on the throttle actuator operation.

  11. A093275E03
    WAVEFORM 10:
    Throttle Actuator Negative Terminal 
    Item
    Content
    Terminal No. (Symbol)
    Between M- and ME01
    Tool Setting
    5 V/DIV., 1 msec./DIV.
    Condition
    Idling with warm engine

    HINT:
    The duty ratio varies depending on the throttle actuator operation.

  12. A164293E01
    WAVEFORM 11:
    Engine Speed Signal 
    Item
    Content
    Terminal No. (Symbol)
    Between TACH and E1
    Tool Setting
    5 V/DIV., 10 msec./DIV.
    Condition
    Idling

    HINT:
    The wavelength becomes shorter as the engine speed increases.

  13. A086154E24
    WAVEFORM 12:
    CAN Communication Signal 
    Item
    Content
    Terminal No. (Symbol)
    Between CANH and E1
    Tool Setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Engine stopped and engine switch on (IG)

    HINT:
    The waveform varies depending on the CAN communication signal.

  14. A086155E25
    WAVEFORM 13:
    CAN Communication Signal 
    Item
    Content
    Terminal No. (Symbol)
    Between CANL and E1
    Tool Setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Engine stopped and engine switch on (IG)

    HINT:
    The waveform varies depending on the CAN communication signal.

  15. A115367E02
    WAVEFORM 14:
    Cam Position Sensor 
    Item
    Content
    Terminal No. (Symbol)
    Between G2 and G2-
    Tool Setting
    2 V/DIV., 200 msec./DIV.
    Condition
    Idling after engine warmed up

    HINT:
    1. The wavelength becomes shorter as engine speed increases.
    2. *1: 720°
    3. *2: 180°
    4. *3: 120°
    5. *4: 60°

  16. G032718E03
    WAVEFORM 15:
    Terminal DI of Air Injection Control Driver 
    Item
    Content
    Terminal No. (Symbol)
    Between AIDI and E1
    Tool Setting
    5 V/DIV., 20 to 40 msec./DIV.
    Condition
    Performing system check using intelligent tester (air injection check)

    HINT:
    The wavelength changes when the air injection control driver detects malfunctions in the air injection system.

← PROBLEM SYMPTOMS TABLE (Sep 2011 – Dec 2011)DIAGNOSIS SYSTEM (Sep 2011 – Dec 2011) →