2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

TERMINALS OF ECM

System information · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


CHECK ECM
A179454E11

HINT:
The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.

Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A38-1 (BATT) - C45-81 (E1)
L - W-B
Battery (for measuring battery voltage and for ECM memory)
Always
11 to 14 V
C45-41 (+BM) - C45-81 (E1)
P - W-B
Power source of throttle actuator
Always
11 to 14 V
A38-28 (IGSW) - C45-81 (E1)
B - W-B
Engine switch
Engine switch on (IG)
11 to 14 V
A38-3 (+B) - C45-81 (E1)
B - W-B
Power source of ECM
Engine switch on (IG)
11 to 14 V
A38-2 (+B2) - C45-81 (E1)
B - W-B
Power source of ECM
Engine switch on (IG)
11 to 14 V
C45-58 (OC1+) - C45-57 (OC1-)
B - B-L
Camshaft oil control valve (OCV) (for Intake Side of Bank 1)
Idling
Pulse generation
(See waveform 1)
C45-52 (OC2+) - C45-51 (OC2-)
L-B - R-B
Camshaft oil control valve (OCV) (for Intake Side of Bank 2)
Idling
Pulse generation
(See waveform 1)
C45-56 (OE1+) - C45-55 (OE1-)
L-W - L-B
Camshaft oil control valve (OCV) (for Exhaust Side of Bank 1)
Idling
Pulse generation
(See waveform 1)
C45-50 (OE2+) - C45-49 (OE2-)
L-R - L-B
Camshaft oil control valve (OCV) (for Exhaust Side of Bank 2)
Idling
Pulse generation
(See waveform 1)
A38-34 (MREL) - C45-81 (E1)
W-R - W-B
EFI relay
Engine switch on (IG)
11 to 14 V
C45-74 (VG) - C45-75 (E2G)
L-Y - G-W
Mass air flow meter
Idling, Shift lever in P or N, A/C switch off
0.5 to 3.0 V
C45-73 (THA) - C45-98 (ETHA)
Y-B - BR
Intake air temperature sensor
Idling, Intake air temperature 20°C (68°F)
0.5 to 3.4 V
C45-76 (THW) - C45-97 (ETHW)
G-B - BR
Engine coolant temperature sensor
Idling, Engine coolant temperature 80°C (176°F)
0.2 to 1.0 V
C45-80 (VCTA) - C45-79 (ETA)
Y - B
Power source of throttle position sensor (specific voltage)
Engine switch on (IG)
4.5 to 5.5 V
C45-78 (VTA1) - C45-79 (ETA)
B-L - B
Throttle position sensor (for engine control)
Engine switch on (IG),
Accelerator pedal fully released
0.5 to 1.1 V
Engine switch on (IG),
Accelerator pedal fully depressed
3.2 to 4.8 V
C45-77 (VTA2) - C45-79 (ETA)
B-R - B
Throttle position sensor (for sensor malfunction detection)
Engine switch on (IG),
Accelerator pedal fully released
2.1 to 3.1 V
Engine switch on (IG),
Accelerator pedal fully depressed
4.6 to 5.0 V
A38-55 (VPA) - A38-58 (EPA)
R - W-L
Accelerator pedal position sensor (for engine control)
Engine switch on (IG),
Accelerator pedal released
0.5 to 1.1 V
Engine switch on (IG),
Accelerator pedal fully depressed
2.6 to 4.5 V
A38-56 (VPA2) - A38-60 (EPA2)
GR-G - BR
Accelerator pedal position sensor (for sensor malfunctioning detection)
Engine switch on (IG),
Accelerator pedal released
1.2 to 2.0 V
Engine switch on (IG),
Accelerator pedal fully depressed
3.4 to 5.0 V
A38-57 (VCPA) - A38-58 (EPA)
L-W - W-L
Power source of accelerator pedal position sensor (for VPA)
Engine switch on (IG)
4.5 to 5.5 V
A38-59 (VCP2) - A38-60 (EPA2)
V - BR
Power source of accelerator pedal position sensor (for VPA2)
Engine switch on (IG)
4.5 to 5.5 V
C45-22 (HA1A) - C45-23 (E04)
L - W-B
A/F sensor heater
bank 1 sensor 1
Idling with warm engine
Pulse generation
(See waveform 2)
Engine switch on (IG)
11 to 14 V
C45-20 (HA2A) - C45-21 (E05)
G - W-B
A/F sensor heater
bank 2 sensor 1
Idling with warm engine
Pulse generation
(See waveform 2)
Engine switch on (IG)
11 to 14 V
C45-126 (A1A+) - C45-81 (E1)
G - W-B
A/F sensor
bank 1 sensor 1
Engine switch on (IG)
3.3 V*
C45-125 (A1A-) - C45-81 (E1)
R - W-B
A/F sensor
bank 1 sensor 1
Engine switch on (IG)
2.9 V*
C45-103 (A2A+) - C45-81 (E1)
P - W-B
A/F sensor
bank 2 sensor 1
Engine switch on (IG)
3.3 V*
C45-102 (A2A-) - C45-81 (E1)
L - W-B
A/F sensor
bank 2 sensor 1
Engine switch on (IG)
2.9 V*
C45-45 (HT1B) - C45-46 (E03)
G-B - W-B
Heated oxygen sensor heater
bank 1 sensor 2
Idling
Below 3.0 V
Engine switch on (IG)
11 to 14 V
C45-44 (HT2B) - C45-46 (E03)
B - W-B
Heated oxygen sensor heater
bank 2 sensor 2
Idling
Below 3.0 V
Engine switch on (IG)
11 to 14 V
C45-114 (OX1B) - C45-115 (EX1B)
G - L
Heated oxygen sensor
bank 1 sensor 2
Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor
Pulse generation
(See waveform 3)
C45-112 (OX2B) - C45-113 (EX2B)
R - W
Heated oxygen sensor
bank 2 sensor 2
Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor
Pulse generation
(See waveform 3)
C45-86 (#10) - C45-43 (E01)
R-L - W-B
Fuel injector
Engine switch on (IG)
11 to 14 V
Idling
Pulse generation
(See waveform 4)
C45-109 (#20) - C45-43 (E01)
L - W-B
Fuel injector
Engine switch on (IG)
11 to 14 V
Idling
Pulse generation
(See waveform 4)
C45-85 (#30) - C45-43 (E01)
R-B - W-B
Fuel injector
Engine switch on (IG)
11 to 14 V
Idling
Pulse generation
(See waveform 4)
C45-108 (#40) - C45-43 (E01)
Y - W-B
Fuel injector
Engine switch on (IG)
11 to 14 V
Idling
Pulse generation
(See waveform 4)
C45-84 (#50) - C45-43 (E01)
G - W-B
Fuel injector
Engine switch on (IG)
11 to 14 V
Idling
Pulse generation
(See waveform 4)
C45-107 (#60) - C45-43 (E01)
R - W-B
Fuel injector
Engine switch on (IG)
11 to 14 V
Idling
Pulse generation
(See waveform 4)
C45-83 (#70) - C45-43 (E01)
W - W-B
Fuel injector
Engine switch on (IG)
11 to 14 V
Idling
Pulse generation
(See waveform 4)
C45-106 (#80) - C45-43 (E01)
R-B - W-B
Fuel injector
Engine switch on (IG)
11 to 14 V
Idling
Pulse generation
(See waveform 4)
C45-94 (KNK1) - C45-93 (EKNK)
R - G
Knock sensor
Engine speed maintained at 4000 rpm after warming up engine
Pulse generation
(See waveform 5)
C45-117 (KNK2) - C45-116 (EKN2)
W - B
Knock sensor
Engine speed maintained at 4000 rpm after warming up engine
Pulse generation
(See waveform 5)
C45-96 (KNK3) - C45-95 (EKN3)
W - B
Knock sensor
Engine speed maintained at 4000 rpm after warming up engine
Pulse generation
(See waveform 5)
C45-119 (KNK4) - C45-118 (EKN4)
R - G
Knock sensor
Engine speed maintained at 4000 rpm after warming up engine
Pulse generation
(See waveform 5)
C45-92 (VV1+) - C45-91 (VV1-)
R - Y
Variable valve timing (VVT) sensor (for Intake Side of Bank 1)
Idling
Pulse generation
(See waveform 6)
C45-87 (VV2+) - C45-88 (VV2-)
R - Y
Variable valve timing (VVT) sensor (for Intake Side for Bank 2)
Idling
Pulse generation
(See waveform 6)
C45-69 (EV1+) - C45-68 (EV1-)
R-L - Y
Variable valve timing (VVT) sensor (for Exhaust Side of Bank 1)
Idling
Pulse generation
(See waveform 16)
C45-64 (EV2+) - C45-65 (EV2-)
R-L - Y
Variable valve timing (VVT) sensor (for Exhaust Side of Bank 2)
Idling
Pulse generation
(See waveform 16)
C45-110 (NE+) - C45-111 (NE-)
W - G-W
Crankshaft position sensor
Idling
Pulse generation
(See waveform 6)
C45-40 (IGT1) - C45-81 (E1)
B-Y - W-B
Ignition coil (ignition signal)
Idling
Pulse generation
(See waveform 7)
C45-33 (IGT2) - C45-81 (E1)
L-B - W-B
Ignition coil (ignition signal)
Idling
Pulse generation
(See waveform 7)
C45-37 (IGT3) - C45-81 (E1)
B - W-B
Ignition coil (ignition signal)
Idling
Pulse generation
(See waveform 7)
C45-34 (IGT4) - C45-81 (E1)
L-B - W-B
Ignition coil (ignition signal)
Idling
Pulse generation
(See waveform 7)
C45-35 (IGT5) - C45-81 (E1)
G-R - W-B
Ignition coil (ignition signal)
Idling
Pulse generation
(See waveform 7)
C45-36 (IGT6) - C45-81 (E1)
G - W-B
Ignition coil (ignition signal)
Idling
Pulse generation
(See waveform 7)
C45-38 (IGT7) - C45-81 (E1)
G-W - W-B
Ignition coil (ignition signal)
Idling
Pulse generation
(See waveform 7)
C45-39 (IGT8) - C45-81 (E1)
G-B - W-B
Ignition coil (ignition signal)
Idling
Pulse generation
(See waveform 7)
C45-104 (IGF1) - C45-81 (E1)
G-B - W-B
Ignition coil (ignition confirmation signal)
Engine switch on (IG)
4.5 to 5.5 V
Idling
Pulse generation
(See waveform 7)
C45-105 (IGF2) - C45-81 (E1)
R - W-B
Ignition coil (ignition confirmation signal)
Engine switch on (IG)
4.5 to 5.5 V
Idling
Pulse generation
(See waveform 7)
C45-63 (PRG) - C45-81 (E1)
L-B - W-B
Purge VSV
Engine switch on (IG)
11 to 14 V
Idling
Pulse generation
(See waveform 8)
A38-13 (SPD) - C45-81 (E1)
V-R - W-B
Speed signal from combination meter
Driving at 20 km/h (12 mph)
Pulse generation
(See waveform 9)
A38-46 (STA) - C45-81 (E1)
R-B - W-B
Starter signal
Cranking
5.5 V or higher
C45-120 (NSW) - C45-81 (E1)
L - W-B
Park/neutral position switch
Engine switch on (IG), Shift lever in other than P and N
11 to 14 V
Engine switch on (IG), Shift lever in P or N
Below 3.0 V
A38-36 (STP) - C45-81 (E1)
R - W-B
Stop light switch
Brake pedal depressed
7.5 to 14 V
Brake pedal released
Below 1.5 V
A38-35 (ST1-) - C45-81 (E1)
R-W - W-B
Stop light switch
(opposite to STP terminal)
Engine switch on (IG),
Brake pedal depressed
Below 1.5 V
Engine switch on (IG),
Brake pedal released
7.5 to 14 V
C45-19 (M+) - C45-82 (ME01)
R - W-B
Throttle actuator
Idling with warm engine
Pulse generation
(See waveform 10)
C45-18 (M-) - C45-82 (ME01)
G - W-B
Throttle actuator
Idling with warm engine
Pulse generation
(See waveform 11)
A38-52 (FPC) - C45-81 (E1)
W - W-B
Fuel pump control
Engine switch on (IG)
Below 1.5 V
A38-24 (W) - C45-81 (E1)
R-Y - W-B
MIL
Engine switch on (IG)
Below 3.0 V
Idling
11 to 14 V
A38-16 (TC) - C45-81 (E1)
V-W - W-B
Terminal TC of DLC3
Engine switch on (IG)
11 to 14 V
A38-15 (TACH) - C45-81 (E1)
W-G - W-B
Engine speed
Idling
Pulse generation
(See waveform 12)
C45-67 (VCV1) - C45-98 (ETHA)
L - BR
Power source for sensor (specific voltage)
Engine switch on (IG)
4.75 to 5.25 V
C45-66 (VCV2) - C45-98 (ETHA)
L - BR
Power source for sensor (specific voltage)
Engine switch on (IG)
4.5 to 5.5 V
C45-32 (ALT) - C45-81 (E1)
R - W-B
Generator
Engine switch on (IG)
11 to 14 V
A38-10 (CANH) - C45-81 (E1)
P - W-B
CAN communication line
Engine switch on (IG)
Pulse generation
(See waveform 13)
A38-11 (CANL) - C45-81 (E1)
B - W-B
CAN communication line
Engine switch on (IG)
Pulse generation
(See waveform 14)
C45-62 (ACIS) - C45-81 (E1)
L-Y - W-B
VSV for ACIS (Acoustic Control Induction System) operation signal
Engine switch on (IG)
11 to 14 V
C45-90 (G2) - C45- 89 (G2-)
G - Y
Camshaft position sensor
Idling
Pulse generation
(See waveform 15)
A38-14 (STSW) - C45-81 (E1)
R - W-B
Starter switch
Shift lever in P or N, Cranking
6.0 V or higher
A38-41 (ACCR) - C45-81 (E1)
L-Y - W-B
ACC relay control signal
Engine switch on (IG) → Cranking
11 to 14 V → Below 1 V
C45-16 (STAR) - C45-81 (E1)
L - W-B
Starter relay control
Engine switch on (IG)
Below 1.5 V
Cranking
5.5 V or higher
C45-72 (PSP) - C45-81 (E1)
G - W-B
Power steering oil pressure sensor
Engine switch on (IG)
0.33 to 3.6 V

HINT:
*: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

  1. A093229E02
    WAVEFORM 1:
    Camshaft Oil Control Valve (OCV) 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    C45-58 (OC1+) - C45-57 (OC1-)
    5 V/DIV., 1 msec./DIV.
    Idling
    C45-52 (OC2+) - C45-51 (OC2-)
    5 V/DIV., 1 msec./DIV.
    Idling
    C45-56 (OE1+) - C45-55 (OE1-)
    5 V/DIV., 1 msec./DIV.
    Idling
    C45-50 (OE2+) - C45-49 (OE2-)
    5 V/DIV., 1 msec./DIV.
    Idling

  2. A172534E02
    WAVEFORM 2:
    A/F Sensor Heater Signal 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    C45-22 (HA1A) - C45-23 (E04)
    5 V/DIV., 10 msec./DIV.
    Idling with warm engine
    C45-20 (HA2A) - C45-21 (E05)
    5 V/DIV., 10 msec./DIV.
    Idling with warm engine

    HINT:
    The wavelength varies in accordance with the engine operating condition.

  3. A088863E05
    WAVEFORM 3:
    Heated Oxygen Sensor 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    C45-114 (OX1B) - C45-115 (EX1B)
    0.2 V/DIV., 200 msec./DIV.
    Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor
    C45-112 (OX2B) - C45-113 (EX2B)
    0.2 V/DIV., 200 msec./DIV.
    Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor

    HINT:
    In the Data List, item O2S B1S2 or O2S B2S2 shows the ECM input values from the heated oxygen sensor.

  4. A093279E04
    WAVEFORM 4:
    Injector No. 1 (to No. 8) Injection Signal 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    C45-86 (#10) - C45-43 (E01)
    20 V/DIV., 20 msec./DIV.
    Idling
    C45-109 (#20) - C45-43 (E01)
    20 V/DIV., 20 msec./DIV.
    Idling
    C45-85 (#30) - C45-43 (E01)
    20 V/DIV., 20 msec./DIV.
    Idling
    C45-108 (#40) - C45-43 (E01)
    20 V/DIV., 20 msec./DIV.
    Idling
    C45-84 (#50) - C45-43 (E01)
    20 V/DIV., 20 msec./DIV.
    Idling
    C45-107 (#60) - C45-43 (E01)
    20 V/DIV., 20 msec./DIV.
    Idling
    C45-83 (#70) - C45-43 (E01)
    20 V/DIV., 20 msec./DIV.
    Idling
    C45-106 (#80) - C45-43 (E01)
    20 V/DIV., 20 msec./DIV.
    Idling

    HINT:
    The wavelength becomes shorter as the engine speed increases.

  5. A085286E03
    WAVEFORM 5:
    Knock Sensor 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    C45-94 (KNK1) - C45-93 (EKNK)
    1 V/DIV., 1 msec./DIV.
    Engine speed maintained at 4000 rpm after warming up engine
    C45-117 (KNK2) - C45-116 (EKN2)
    1 V/DIV., 1 msec./DIV.
    Engine speed maintained at 4000 rpm after warming up engine
    C45-96 (KNK3) - C45-95 (EKN3)
    1 V/DIV., 1 msec./DIV.
    Engine speed maintained at 4000 rpm after warming up engine
    C45-119 (KNK4) - C45-118 (EKN4)
    1 V/DIV., 1 msec./DIV.
    Engine speed maintained at 4000 rpm after warming up engine

    HINT:
    1. The wavelength becomes shorter as the engine speed increases.
    2. The waveforms and amplitudes displayed differ slightly depending on the vehicle.

  6. A217926E03
    WAVEFORM 6:
    Crankshaft Position Sensor and VVT Sensor for Intake Side 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    (a) C45-110 (NE+) - C45-111 (NE-)
    5 V/DIV., 20 msec./DIV.
    Idle after engine warmed up
    (b) C45-92 (VV1+) - C45-91 (VV1-)
    5 V/DIV., 20 msec./DIV.
    Idle after engine warmed up
    (c) C45-87 (VV2+) - C45-88 (VV2-)
    5 V/DIV., 20 msec./DIV.
    Idle after engine warmed up

    HINT:
    The wavelength becomes shorter as engine speed increases.

  7. A093278E14
    WAVEFORM 7:
    Igniter IGT Signal (from ECM to Igniter) and Igniter IGF Signal (from Igniter to ECM) 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    (a) C45-40 (IGT1) - C45-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (a) C45-33 (IGT2) - C45-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (a) C45-37 (IGT3) - C45-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (a) C45-34 (IGT4) - C45-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (a) C45-35 (IGT5) - C45-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (a) C45-36 (IGT6) - C45-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (a) C45-38 (IGT7) - C45-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (a) C45-39 (IGT8) - C45-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (b) C45-104 (IGF1) - C45-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (b) C45-105 (IGF2) - C45-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling

    HINT:
    The wavelength becomes shorter as engine speed increases.

  8. A149742E22
    WAVEFORM 8:
    Purge VSV 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    C45-63 (PRG) - C45-81 (E1)
    10 V/DIV., 20 msec./DIV.
    Idling

    HINT:
    If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.

  9. A093224E01
    WAVEFORM 9:
    Vehicle Speed Signal 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    A38-13 (SPD) - C45-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Driving at 20 km/h (12 mph)

    HINT:
    The wavelength becomes shorter as the vehicle speed increases.

  10. A208000E21
    WAVEFORM 10:
    Throttle Actuator Positive Terminal 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    C45-19 (M+) - C45-82 (ME01)
    5 V/DIV., 1 msec./DIV.
    Idling with warm engine

    HINT:
    The duty ratio varies depending on the throttle actuator operation.

  11. A093274E03
    WAVEFORM 11:
    Throttle Actuator Negative Terminal 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    C45-18 (M-) - C45-82 (ME01)
    5 V/DIV., 1 msec./DIV.
    Idling with warm engine

    HINT:
    The duty ratio varies depending on the throttle actuator operation.

  12. A164293E01
    WAVEFORM 12:
    Engine Speed Signal 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    A38-15 (TACH) - C45-81 (E1)
    5 V/DIV., 10 msec./DIV.
    Idling

    HINT:
    The wavelength becomes shorter as the engine speed increases.

  13. A086154E24
    WAVEFORM 13:
    CAN Communication Signal (Reference) 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    A38-10 (CANH) - C45-81 (E1)
    1 V/DIV., 10 μsec./DIV.
    Engine stops and engine switch on (IG)

    HINT:
    The waveform varies depending on the CAN communication signal.

  14. A086155E25
    WAVEFORM 14:
    CAN Communication Signal (Reference) 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    A38-11 (CANL) - C45-81 (E1)
    1 V/DIV., 10 μsec./DIV.
    Engine stops and engine switch on (IG)

    HINT:
    The waveform varies depending on the CAN communication signal.

  15. A211721E03
    WAVEFORM 15:
    Crankshaft Position Sensor and Camshaft Position Sensor 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    CH1: C45-110 (NE+) - C45-111 (NE-)
    5 V/DIV., 20 msec./DIV.
    Idle after engine warmed up
    CH2: C45-90 (G2) - C45-89 (G2-)
    5 V/DIV., 20 msec./DIV.
    Idle after engine warmed up

    HINT:
    The wavelength becomes shorter as the engine speed increases.

  16. A217927E03
    WAVEFORM 16:
    Crankshaft Position Sensor and VVT Sensor for Exhaust Side 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    (a) C45-110 (NE+) - C45-111 (NE-)
    5 V/DIV., 20 msec./DIV.
    Idle after engine warmed up
    (b) C45-69 (EV1+) - C45-68 (EV1-)
    5 V/DIV., 20 msec./DIV.
    Idle after engine warmed up
    (c) C45-64 (EV2+) - C45-65 (EV2-)
    5 V/DIV., 20 msec./DIV.
    Idle after engine warmed up

    HINT:
    The wavelength becomes shorter as engine speed increases.

← TERMINALS OF ECM (Sep 2011 – Dec 2011)DIAGNOSIS SYSTEM (Sep 2011 – Dec 2011) →