2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

TERMINALS OF ECM

System information · Vehicles built from Jan 2012


CHECK ECM
A182253E10
  1. Measure the voltage according to the value(s) in the table below.

    HINT:
    The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A52*1-1 (BATT) - C46*1-81 (E1)
    A38*2-1 (BATT) - C45*2-81 (E1)
    L - BR
    Battery (for measuring battery voltage and for ECM memory)
    Always
    11 to 14 V
    C46*1-41 (+BM) - C46*1-81 (E1)
    C45*2-41 (+BM) - C45*2-81 (E1)
    P - BR
    Power source of throttle actuator
    Always
    11 to 14 V
    A52*1-28 (IGSW) - C46*1-81 (E1)
    A38*2-28 (IGSW) - C45*2-81 (E1)
    B - BR
    Engine switch
    engine switch on (IG)
    11 to 14 V
    A52*1-3 (+B) - C46*1-81 (E1)
    A38*2-3 (+B) - C45*2-81 (E1)
    B - BR
    Power source of ECM
    engine switch on (IG)
    11 to 14 V
    A52*1-2 (+B2) - C46*1-81 (E1)
    A38*2-2 (+B2) - C45*2-81 (E1)
    B - BR
    Power source of ECM
    engine switch on (IG)
    11 to 14 V
    C46*1-58 (OC1+) - C46*1-57 (OC1-)
    C45*2-58 (OC1+) - C45*2-57 (OC1-)
    B - B-L
    Camshaft timing oil control valve (OCV) (for Intake Side of Bank 1)
    Idling
    Pulse generation
    (see waveform 1)
    C46*1-52 (OC2+) - C46*1-51 (OC2-)
    C45*2-52 (OC2+) - C45*2-51 (OC2-)
    L-B - R-B
    Camshaft timing oil control valve (OCV) (for Intake Side of Bank 2)
    Idling
    Pulse generation
    (see waveform 1)
    C46*1-56 (OE1+) - C46*1-55 (OE1-)
    C45*2-56 (OE1+) - C45*2-55 (OE1-)
    L-W - L-B
    Camshaft timing oil control valve (OCV) (for Exhaust Side of Bank 1)
    Idling
    Pulse generation
    (see waveform 1)
    C46*1-50 (OE2+) - C46*1-49 (OE2-)
    C45*2-50 (OE2+) - C45*2-49 (OE2-)
    L-R - L-B
    Camshaft timing oil control valve (OCV) (for Exhaust Side of Bank 2)
    Idling
    Pulse generation
    (see waveform 1)
    A52*1-34 (MREL) - C46*1-81 (E1)
    A38*2-34 (MREL) - C45*2-81 (E1)
    W-R - BR
    EFI relay
    engine switch on (IG)
    11 to 14 V
    C46*1-74 (VG) - C46*1-75 (E2G)
    C45*2-74 (VG) - C45*2-75 (E2G)
    L-Y - G-W
    Mass air flow meter
    Idling, Shift lever position P or N, A/C switch OFF
    0.5 to 3.0 V
    C46*1-73 (THA) - C46*1-98 (E2)
    C45*2-73 (THA) - C45*2-98 (E2)
    Y-B - BR
    Intake air temperature sensor
    Idling, Intake air temperature 20°C (68°F)
    0.5 to 3.4 V
    C46*1-76 (THW) - C46*1-98 (E2)
    C45*2-76 (THW) - C45*2-98 (E2)
    G-B - BR
    Engine coolant temperature sensor
    Idling, Engine coolant temperature 80°C (176°F)
    0.2 to 1.0 V
    C46*1-80 (VCTA) - C46*1-79 (ETA)
    C45*2-80 (VCTA) - C45*2-79 (ETA)
    Y - L
    Power source of throttle position sensor (specific voltage)
    engine switch on (IG)
    4.5 to 5.5 V
    C46*1-78 (VTA1) - C46*1-79 (ETA)
    C45*2-78 (VTA1) - C45*2-79 (ETA)
    R-Y - L
    Throttle position sensor (for engine control)
    engine switch on (IG),
    Throttle valve fully closed
    0.5 to 1.2 V
    engine switch on (IG),
    Throttle valve fully open
    3.2 to 4.8 V
    C46*1-77 (VTA2) - C46*1-79 (ETA)
    C45*2-77 (VTA2) - C45*2-79 (ETA)
    Y-B - L
    Throttle position sensor (for sensor malfunction detection)
    engine switch on (IG),
    Throttle valve fully closed
    2.1 to 3.1 V
    engine switch on (IG),
    Throttle valve fully open
    4.5 to 5.5 V
    A52*1-55 (VPA) - A52*1-58 (EPA)
    A38*2-55 (VPA) - A38*2-58 (EPA)
    R - W-L
    Accelerator pedal position sensor (for engine control)
    engine switch on (IG),
    Accelerator pedal released
    0.5 to 1.1 V
    engine switch on (IG),
    Accelerator pedal fully depressed
    2.6 to 4.5 V
    A52*1-56 (VPA2) - A52*1-60 (EPA2)
    A38*2-56 (VPA2) - A38*2-60 (EPA2)
    GR-G - BR
    Accelerator pedal position sensor (for sensor malfunctioning detection)
    engine switch on (IG),
    Accelerator pedal released
    1.2 to 2.0 V
    engine switch on (IG),
    Accelerator pedal fully depressed
    3.4 to 5.3 V
    A52*1-57 (VCPA) - A52*1-58 (EPA)
    A38*2-57 (VCPA) - A38*2-58 (EPA)
    L-W - W-L
    Power source of accelerator pedal position sensor (for VPA)
    engine switch on (IG)
    4.5 to 5.5 V
    A52*1-59 (VCP2) - A52*1-60 (EPA2)
    A38*2-59 (VCP2) - A38*2-60 (EPA2)
    V - BR
    Power source of accelerator pedal position sensor (for VPA2)
    engine switch on (IG)
    4.5 to 5.5 V
    C46*1-22 (HA1A) - C46*1-23 (E04)
    C45*2-22 (HA1A) - C45*2-23 (E04)
    L - W-B
    A/F sensor heater
    Idling
    Below 3.0 V
    engine switch on (IG)
    11 to 14 V
    C46*1-20 (HA2A) - C46*1-21 (E05)
    C45*2-20 (HA2A) - C45*2-21 (E05)
    G - W-B
    A/F sensor heater
    Idling
    Below 3.0 V
    engine switch on (IG)
    11 to 14 V
    C46*1-126 (A1A+) - C46*1-81 (E1)
    C45*2-126 (A1A+) - C45*2-81 (E1)
    G -BR
    A/F sensor
    engine switch on (IG)
    3.3 V*3
    C46*1-125 (A1A-) - C46*1-81 (E1)
    C45*2-125 (A1A-) - C45*2-81 (E1)
    R - BR
    A/F sensor
    engine switch on (IG)
    2.9 V*3
    C46*1-103 (A2A+) - C46*1-81 (E1)
    C45*2-103 (A2A+) - C45*2-81 (E1)
    P - BR
    A/F sensor
    engine switch on (IG)
    3.3 V*3
    C46*1-102 (A2A-) - C46*1-81 (E1)
    C45*2-102 (A2A-) - C45*2-81 (E1)
    L - BR
    A/F sensor
    engine switch on (IG)
    2.9 V*3
    C46*1-45 (HT1B) - C46*1-46 (E03)
    C45*2-45 (HT1B) - C45*2-46 (E03)
    G-B - W-B
    Heated oxygen sensor heater
    Idling
    Below 3.0 V
    engine switch on (IG)
    11 to 14 V
    C46*1-44 (HT2B) - C46*1-46 (E03)
    C45*2-44 (HT2B) - C45*2-46 (E03)
    B - W-B
    Heated oxygen sensor heater
    Idling
    Below 3.0 V
    engine switch on (IG)
    11 to 14 V
    C46*1-114 (OX1B) - C46*1-115 (EX1B)
    C45*2-114 (OX1B) - C45*2-115 (EX1B)
    G - L
    Heated oxygen sensor
    Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor
    Pulse generation
    (see waveform 2)
    C46*1-112 (OX2B) - C46*1-113 (EX2B)
    C45*2-112 (OX2B) - C45*2-113 (EX2B)
    R - W
    Heated oxygen sensor
    Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor
    Pulse generation
    (see waveform 2)
    C46*1-86 (#10) - C46*1-43 (E01)
    C45*2-86 (#10) - C45*2-43 (E01)
    R-L - W-B
    Injector
    engine switch on (IG)
    11 to 14 V
    Idling
    Pulse generation
    (see waveform 3)
    C46*1-109 (#20) - C46*1-43 (E01)
    C45*2-109 (#20) - C45*2-43 (E01)
    L - W-B
    Injector
    engine switch on (IG)
    11 to 14 V
    Idling
    Pulse generation
    (see waveform 3)
    C46*1-85 (#30) - C46*1-43 (E01)
    C45*2-85 (#30) - C45*2-43 (E01)
    R-B - W-B
    Injector
    engine switch on (IG)
    11 to 14 V
    Idling
    Pulse generation
    (see waveform 3)
    C46*1-108 (#40) - C46*1-43 (E01)
    C45*2-108 (#40) - C45*2-43 (E01)
    Y - W-B
    Injector
    engine switch on (IG)
    11 to 14 V
    Idling
    Pulse generation
    (see waveform 3)
    C46*1-84 (#50) - C46*1-43 (E01)
    C45*2-84 (#50) - C45*2-43 (E01)
    G - W-B
    Injector
    engine switch on (IG)
    11 to 14 V
    Idling
    Pulse generation
    (see waveform 3)
    C46*1-107 (#60) - C46*1-43 (E01)
    C45*2-107 (#60) - C45*2-43 (E01)
    R - W-B
    Injector
    engine switch on (IG)
    11 to 14 V
    Idling
    Pulse generation
    (see waveform 3)
    C46*1-83 (#70) - C46*1-43 (E01)
    C45*2-83 (#70) - C45*2-43 (E01)
    W - W-B
    Injector
    engine switch on (IG)
    11 to 14 V
    Idling
    Pulse generation
    (see waveform 3)
    C46*1-106 (#80) - C46*1-43 (E01)
    C45*2-106 (#80) - C45*2-43 (E01)
    R-B - W-B
    Injector
    engine switch on (IG)
    11 to 14 V
    Idling
    Pulse generation
    (see waveform 3)
    C46*1-94 (KNK1) - C46*1-93 (EKNK)
    C45*2-94 (KNK1) - C45*2-93 (EKNK)
    R - G
    Knock sensor
    Engine speed maintained at 4000 rpm after warming up engine
    Pulse generation
    (see waveform 4)
    C46*1-117 (KNK2) - C46*1-116 (EKN2)
    C45*2-117 (KNK2) - C45*2-116 (EKN2)
    W - B
    Knock sensor
    Engine speed maintained at 4000 rpm after warming up engine
    Pulse generation
    (see waveform 4)
    C46*1-96 (KNK3) - C46*1-95 (EKN3)
    C45*2-96 (KNK3) - C45*2-95 (EKN3)
    W - B
    Knock sensor
    Engine speed maintained at 4000 rpm after warming up engine
    Pulse generation
    (see waveform 4)
    C46*1-119 (KNK4) - C46*1-118 (EKN4)
    C45*2-119 (KNK4) - C45*2-118 (EKN4)
    R - G
    Knock sensor
    Engine speed maintained at 4000 rpm after warming up engine
    Pulse generation
    (see waveform 4)
    C46*1-92 (VV1+) - C46*1-91 (VV1-)
    C45*2-92 (VV1+) - C45*2-91 (VV1-)
    R - Y
    Variable valve timing (VVT) sensor (for Intake Side of Bank 1)
    Idling
    Pulse generation
    (see waveform 5)
    C46*1-87 (VV2+) - C46*1-88 (VV2-)
    C45*2-87 (VV2+) - C45*2-88 (VV2-)
    R - Y
    Variable valve timing (VVT) sensor (for Intake Side for Bank 2)
    Idling
    Pulse generation
    (see waveform 5)
    C46*1-69 (EV1+) - C46*1-68 (EV1-)
    C45*2-69 (EV1+) - C45*2-68 (EV1-)
    R-L - Y
    Variable valve timing (VVT) sensor (for Exhaust Side of Bank 1)
    Idling
    Pulse generation
    (see waveform 16)
    C46*1-64 (EV2+) - C46*1-65 (EV2-)
    C45*2-64 (EV2+) - C45*2-65 (EV2-)
    R-L - Y
    Variable valve timing (VVT) sensor (for Exhaust Side of Bank 2)
    Idling
    Pulse generation
    (see waveform 16)
    C46*1-110 (NE+) - C46*1-111 (NE-)
    C45*2-110 (NE+) - C45*2-111 (NE-)
    W - Y
    Crankshaft position sensor
    Idling
    Pulse generation
    (see waveform 5)
    C46*1-40 (IGT1) - C46*1-81 (E1)
    C45*2-40 (IGT1) - C45*2-81 (E1)
    B-Y - BR
    Ignition coil (ignition signal)
    Idling
    Pulse generation
    (see waveform 6)
    C46*1-33 (IGT2) - C46*1-81 (E1)
    C45*2-33 (IGT2) - C45*2-81 (E1)
    L-B - BR
    Ignition coil (ignition signal)
    Idling
    Pulse generation
    (see waveform 6)
    C46*1-37 (IGT3) - C46*1-81 (E1)
    C45*2-37 (IGT3) - C45*2-81 (E1)
    B - BR
    Ignition coil (ignition signal)
    Idling
    Pulse generation
    (see waveform 6)
    C46*1-34 (IGT4) - C46*1-81 (E1)
    C45*2-34 (IGT4) - C45*2-81 (E1)
    L-B - BR
    Ignition coil (ignition signal)
    Idling
    Pulse generation
    (see waveform 6)
    C46*1-35 (IGT5) - C46*1-81 (E1)
    C45*2-35 (IGT5) - C45*2-81 (E1)
    G-R - BR
    Ignition coil (ignition signal)
    Idling
    Pulse generation
    (see waveform 6)
    C46*1-36 (IGT6) - C46*1-81 (E1)
    C45*2-36 (IGT6) - C45*2-81 (E1)
    G - BR
    Ignition coil (ignition signal)
    Idling
    Pulse generation
    (see waveform 6)
    C46*1-38 (IGT7) - C46*1-81 (E1)
    C45*2-38 (IGT7) - C45*2-81 (E1)
    G-W - BR
    Ignition coil (ignition signal)
    Idling
    Pulse generation
    (see waveform 6)
    C46*1-39 (IGT8) - C46*1-81 (E1)
    C45*2-39 (IGT8) - C45*2-81 (E1)
    G-B - BR
    Ignition coil (ignition signal)
    Idling
    Pulse generation
    (see waveform 6)
    C46*1-104 (IGF1) - C46*1-81 (E1)
    C45*2-104 (IGF1) - C45*2-81 (E1)
    G-B - BR
    Ignition coil (ignition confirmation signal)
    engine switch on (IG)
    4.5 to 5.5 V
    Idling
    Pulse generation
    (see waveform 6)
    C46*1-105 (IGF2) - C46*1-81 (E1)
    C45*2-105 (IGF2) - C45*2-81 (E1)
    R - BR
    Ignition coil (ignition confirmation signal)
    engine switch on (IG)
    4.5 to 5.5 V
    Idling
    Pulse generation
    (see waveform 6)
    C46*1-63 (PRG) - C46*1-81 (E1)
    C45*2-63 (PRG) - C45*2-81 (E1)
    L-B - BR
    Purge VSV
    engine switch on (IG)
    11 to 14 V
    Idling
    Pulse generation
    (see waveform 7)
    A52*1-13 (SPD) - C46*1-81 (E1)
    A38*2-13 (SPD) - C45*2-81 (E1)
    V-R - BR
    Speed signal from combination meter
    Driving at 20 km/h (12 mph)
    Pulse generation
    (see waveform 8)
    A52*1-46 (STA) - C46*1-81 (E1)
    A38*2-46 (STA) - C45*2-81 (E1)
    R-B - BR
    Starter signal
    Cranking
    5.5 V or more
    C46*1-120 (NSW) - C46*1-81 (E1)
    C45*2-120 (NSW) - C45*2-81 (E1)
    L - BR
    Park / neutral position switch
    engine switch on (IG), Shift lever position other than P and N
    11 to 14 V
    engine switch on (IG), Shift lever position in P or N
    Below 3.0 V
    A52*1-36 (STP) - C46*1-81 (E1)
    A38*2-36 (STP) - C45*2-81 (E1)
    R - BR
    Stop light switch
    Brake pedal depressed
    7.5 to 14 V
    Brake pedal released
    Below 1.5 V
    A52*1-35 (ST1-) - C46*1-81 (E1)
    A38*2-35 (ST1-) - C45*2-81 (E1)
    R-W - BR
    Stop light switch
    (opposite to STP terminal)
    engine switch on (IG),
    Brake pedal depressed
    Below 1.5 V
    engine switch on (IG),
    Brake pedal released
    7.5 to 14 V
    C46*1-19 (M+) - C46*1-82 (ME01)
    C45*2-19 (M+) - C45*2-82 (ME01)
    R - W-B
    Throttle actuator
    Idling with warm engine
    Pulse generation
    (see waveform 9)
    C46*1-18 (M-) - C46*1-82 (ME01)
    C45*2-18 (M-) - C45*2-82 (ME01)
    G - W-B
    Throttle actuator
    Idling with warm engine
    Pulse generation
    (see waveform 10)
    A52*1-52 (FPC) - C46*1-81 (E1)
    A38*2-52 (FPC) - C45*2-81 (E1)
    W - BR
    Fuel pump control
    engine switch on (IG)
    Below 1.5 V
    A52*1-24 (W) - C46*1-81 (E1)
    A38*2-24 (W) - C45*2-81 (E1)
    R-Y - BR
    MIL
    engine switch on (IG)
    Below 3.0 V
    Idling
    11 to 14 V
    A52*1-16 (TC) - C46*1-81 (E1)
    A38*2-16 (TC) - C45*2-81 (E1)
    V-W - BR
    Terminal TC of DLC3
    engine switch on (IG)
    11 to 14 V
    A52*1-15 (TACH) - C46*1-81 (E1)
    A38*2-15 (TACH) - C45*2-81 (E1)
    W-G - BR
    Engine speed
    Idling
    Pulse generation
    (see waveform 11)
    C46*1-67 (VCV1) - C46*1-98 (E2)
    C45*2-67 (VCV1) - C45*2-98 (E2)
    L - BR
    Power source for sensor (specific voltage)
    engine switch on (IG)
    4.5 to 5.5 V
    C46*1-66 (VCV2) - C46*1-98 (E2)
    C45*2-66 (VCV2) - C45*2-98 (E2)
    L - BR
    Power source for sensor (specific voltage)
    engine switch on (IG)
    4.5 to 5.5 V
    C46*1-32 (ALT) - C46*1-81 (E1)
    C45*2-32 (ALT) - C45*2-81 (E1)
    R - BR
    Generator
    engine switch on (IG)
    11 to 14 V
    A52*1-10 (CANH) - C46*1-81 (E1)
    A38*2-10 (CANH) - C45*2-81 (E1)
    P - BR
    CAN communication line
    engine switch on (IG)
    Pulse generation
    (see waveform 12)
    A52*1-11 (CANL) - C46*1-81 (E1)
    A38*2-11 (CANL) - C45*2-81 (E1)
    B - BR
    CAN communication line
    engine switch on (IG)
    Pulse generation
    (see waveform 13)
    C46*1-62 (ACIS) - C46*1-81 (E1)
    C45*2-62 (ACIS) - C45*2-81 (E1)
    L-Y - BR
    VSV for ACIS (Acoustic Control Induction System) operation signal
    engine switch on (IG)
    11 to 14 V
    C46*1-28 (AIRV) - C46*1-81 (E1)
    C45*2-28 (AIRV) - C45*2-81 (E1)
    BR - BR
    Air switching valve signal for secondary air injection system
    engine switch on (IG)
    11 to 14 V
    C46*1-54 (AIRP) - C46*1-81 (E1)
    C45*2-54 (AIRP) - C45*2-81 (E1)
    P - BR
    Air pump control signal for secondary air injection system
    engine switch on (IG)
    11 to 14 V
    C46*1-30 (AIDI) - C46*1-81 (E1)
    C45*2-30 (AIDI) - C45*2-81 (E1)
    G - BR
    Diagnostic information signal for secondary air injection system
    Air injection system operates
    Pulse generation
    (see waveform 15)
    A52*1-54 (AIP) - C46*1-98 (E2)
    A38*2-54 (AIP) - C45*2-98 (E2)
    P-L - BR
    Secondary air injection system pressure signal
    engine switch on (IG)
    3.0 to 3.6 V
    A52*1-53 (AIP2) - C46*1-98 (E2)
    A38*2-53 (AIP2) - C45*2-98 (E2)
    LG-B - BR
    Secondary air injection system pressure signal
    engine switch on (IG)
    3.0 to 3.6 V
    C46*1-60 (HAI1) - C46*1-81 (E1)
    C45*2-60 (HAI1) - C45*2-81 (E1)
    G - BR
    Air pump heater for secondary air injection system
    AI heater operating
    11 to 14 V
    C46*1-61 (AIR1) - C46*1-81 (E1)
    C45*2-61 (AIR1) - C45*2-81 (E1)
    R - BR
    Air pump for secondary air injection system
    AI operating
    11 to 14 V
    C46*1-90 (G2) - C46*1- 89 (G2-)
    C45*2-90 (G2) - C45*2- 89 (G2-)
    G - Y
    Camshaft position sensor
    Idling
    Pulse generation
    (see waveform 14)
    A52*1-14 (STSW) - C46*1-81 (E1)
    A38*2-14 (STSW) - C45*2-81 (E1)
    R - BR
    Starter switch
    Shift lever position P or N, Cranking
    6.0 V or more
    A52*1-41 (ACCR) - C46*1-81 (E1)
    A38*2-41 (ACCR) - C45*2-81 (E1)
    L-Y - BR
    ACC relay control signal
    engine switch on (IG) → Cranking
    11 to 14 V → Below 1 V
    C46*1-16 (STAR) - C46*1-81 (E1)
    C45*2-16 (STAR) - C45*2-81 (E1)
    L - BR
    Starter relay control
    engine switch on (IG)
    Below 1.5 V
    Cranking
    5.5 V or more
    C46*1-72 (PSP) - C46*1-81 (E1)
    C45*2-72 (PSP) - C45*2-81 (E1)
    G - BR
    Power steering oil pressure switch
    engine switch on (IG)
    0.5 to 4.5 V

    HINT:
    1. *1: for RHD
    2. *2: for LHD
    3. *3: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

  2. A093229E02
    WAVEFORM 1:
    Camshaft timing oil control valve (OCV) 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    C46*1-58 (OC1+) - C46*1-57 (OC1-)
    C45*2-58 (OC1+) - C45*2-57 (OC1-)
    5 V/DIV., 1 msec./DIV.
    Idling
    C46*1-52 (OC2+) - C46*1-51 (OC2-)
    C45*2-52 (OC2+) - C45*2-51 (OC2-)
    5 V/DIV., 1 msec./DIV.
    Idling
    C46*1-56 (OE1+) - C46*1-55 (OE1-)
    C45*2-56 (OE1+) - C45*2-55 (OE1-)
    5 V/DIV., 1 msec./DIV.
    Idling
    C46*1-50 (OE2+) - C46*1-49 (OE2-)
    C45*2-50 (OE2+) - C45*2-49 (OE2-)
    5 V/DIV., 1 msec./DIV.
    Idling

  3. A088863E05
    WAVEFORM 2:
    Heated oxygen sensor 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    C46*1-114 (OX1B) - C46*1-115 (EX1B)
    C45*2-114 (OX1B) - C45*2-115 (EX1B)
    0.2 V/DIV., 200 msec./DIV.
    Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor
    C46*1-112 (OX2B) - C46*1-113 (EX2B)
    C45*2-112 (OX2B) - C45*2-113 (EX2B)
    0.2 V/DIV., 200 msec./DIV.
    Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor

    HINT:
    In DATA LIST, item O2S B1S2 or O2S B2S2 shows the ECM input values from the heated oxygen sensor.

  4. A093279E04
    WAVEFORM 3:
    Injector No. 1 (to No. 8) injection signal 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    C46*1-86 (#10) - C46*1-43 (E01)
    C45*2-86 (#10) - C45*2-43 (E01)
    20 V/DIV., 20 msec./DIV.
    Idling
    C46*1-109 (#20) - C46*1-43 (E01)
    C45*2-109 (#20) - C45*2-43 (E01)
    20 V/DIV., 20 msec./DIV.
    Idling
    C46*1-85 (#30) - C46*1-43 (E01)
    C45*2-85 (#30) - C45*2-43 (E01)
    20 V/DIV., 20 msec./DIV.
    Idling
    C46*1-108 (#40) - C46*1-43 (E01)
    C45*2-108 (#40) - C45*2-43 (E01)
    20 V/DIV., 20 msec./DIV.
    Idling
    C46*1-84 (#50) - C46*1-43 (E01)
    C45*2-84 (#50) - C45*2-43 (E01)
    20 V/DIV., 20 msec./DIV.
    Idling
    C46*1-107 (#60) - C46*1-43 (E01)
    C45*2-107 (#60) - C45*2-43 (E01)
    20 V/DIV., 20 msec./DIV.
    Idling
    C46*1-83 (#70) - C46*1-43 (E01)
    C45*2-83 (#70) - C45*2-43 (E01)
    20 V/DIV., 20 msec./DIV.
    Idling
    C46*1-106 (#80) - C46*1-43 (E01)
    C45*2-106 (#80) - C45*2-43 (E01)
    20 V/DIV., 20 msec./DIV.
    Idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.

  5. A085286E03
    WAVEFORM 4:
    Knock sensor 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    C46*1-94 (KNK1) - C46*1-93 (EKNK)
    C45*2-94 (KNK1) - C45*2-93 (EKNK)
    1 V/DIV., 1 msec./DIV.
    Engine speed maintained at 4000 rpm after warming up engine
    C46*1-117 (KNK2) - C46*1-116 (EKN2)
    C45*2-117 (KNK2) - C45*2-116 (EKN2)
    1 V/DIV., 1 msec./DIV.
    Engine speed maintained at 4000 rpm after warming up engine
    C46*1-96 (KNK3) - C46*1-95 (EKN3)
    C45*2-96 (KNK3) - C45*2-95 (EKN3)
    1 V/DIV., 1 msec./DIV.
    Engine speed maintained at 4000 rpm after warming up engine
    C46*1-119 (KNK4) - C46*1-118 (EKN4)
    C45*2-119 (KNK4) - C45*2-118 (EKN4)
    1 V/DIV., 1 msec./DIV.
    Engine speed maintained at 4000 rpm after warming up engine

    HINT:
    1. The wavelength becomes shorter as the engine rpm increases.
    2. The waveforms and amplitudes displayed differ slightly depending on the vehicle.

  6. A217926E01
    WAVEFORM 5:
    Crankshaft position sensor and VVT sensor for intake side 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    (a) C46*1-110 (NE+) - C46*1-111 (NE-)
    (a) C45*2-110 (NE+) - C45*2-111 (NE-)
    5 V/DIV., 20 msec./DIV.
    Idle after engine warmed up
    (b) C46*1-92 (VV1+) - C46*1-91 (VV1-)
    (b) C45*2-92 (VV1+) - C45*2-91 (VV1-)
    5 V/DIV., 20 msec./DIV.
    Idle after engine warmed up
    (c) C46*1-87 (VV2+) - C46*1-88 (VV2-)
    (c) C45*2-87 (VV2+) - C45*2-88 (VV2-)
    5 V/DIV., 20 msec./DIV.
    Idle after engine warmed up

    HINT:
    The wavelength becomes shorter as engine rpm increases.

  7. A093278E14
    WAVEFORM 6:
    Igniter IGT signal (from ECM to igniter) and Igniter IGF signal (from igniter to ECM) 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    (a) C46*1-40 (IGT1) - C46*1-81 (E1)
    (a) C45*2-40 (IGT1) - C45*2-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (a) C46*1-33 (IGT2) - C46*1-81 (E1)
    (a) C45*2-33 (IGT2) - C45*2-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (a) C46*1-37 (IGT3) - C46*1-81 (E1)
    (a) C45*2-37 (IGT3) - C45*2-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (a) C46*1-34 (IGT4) - C46*1-81 (E1)
    (a) C45*2-34 (IGT4) - C45*2-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (a) C46*1-35 (IGT5) - C46*1-81 (E1)
    (a) C45*2-35 (IGT5) - C45*2-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (a) C46*1-36 (IGT6) - C46*1-81 (E1)
    (a) C45*2-36 (IGT6) - C45*2-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (a) C46*1-38 (IGT7) - C46*1-81 (E1)
    (a) C45*2-38 (IGT7) - C45*2-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (a) C46*1-39 (IGT8) - C46*1-81 (E1)
    (a) C45*2-39 (IGT8) - C45*2-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (b) C46*1-104 (IGF1) - C46*1-81 (E1)
    (b) C45*2-104 (IGF1) - C45*2-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (b) C46*1-105 (IGF2) - C46*1-81 (E1)
    (b) C45*2-105 (IGF2) - C45*2-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling

    HINT:
    The wavelength becomes shorter as engine rpm increases.

  8. A218020E03
    WAVEFORM 7:
    Purge VSV 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    C46*1-63 (PRG) - C46*1-81 (E1)
    C45*2-63 (PRG) - C45*2-81 (E1)
    10 V/DIV., 10 to 100 msec./DIV.
    Idling

    HINT:
    If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.

  9. A093224E01
    WAVEFORM 8:
    Vehicle speed signal 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    A52*1-13 (SPD) - C46*1-81 (E1)
    A38*2-13 (SPD) - C45*2-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Driving at 20 km/h (12 mph)

    HINT:
    The wavelength becomes shorter as the vehicle speed increases.

  10. A208000E06
    WAVEFORM 9:
    Throttle actuator positive terminal 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    C46*1-19 (M+) - C46*1-82 (ME01)
    C45*2-19 (M+) - C45*2-82 (ME01)
    5 V/DIV., 1 msec./DIV.
    Idling with warm engine

    HINT:
    The duty ratio varies depending on the throttle actuator operation.

  11. A245848E04
    WAVEFORM 10:
    Throttle actuator negative terminal 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    C46*1-18 (M-) - C46*1-82 (ME01)
    C45*2-18 (M-) - C45*2-82 (ME01)
    5 V/DIV., 1 msec./DIV.
    Idling with warm engine

    HINT:
    The duty ratio varies depending on the throttle actuator operation.

  12. A164293E01
    WAVEFORM 11:
    Engine speed signal 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    A52*1-15 (TACH) - C46*1-81 (E1)
    A38*2-15 (TACH) - C45*2-81 (E1)
    5 V/DIV., 10 msec./DIV.
    Idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.

  13. A086154E24
    WAVEFORM 12:
    CAN communication signal 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    A52*1-10 (CANH) - C46*1-81 (E1)
    A38*2-10 (CANH) - C45*2-81 (E1)
    1 V/DIV., 10 μsec./DIV.
    Engine stops and engine switch on (IG)

    HINT:
    The waveform varies depending on the CAN communication signal.

  14. A086155E25
    WAVEFORM 13:
    CAN communication signal 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    A52*1-11 (CANL) - C46*1-81 (E1)
    A38*2-11 (CANL) - C45*2-81 (E1)
    1 V/DIV., 10 μsec./DIV.
    Engine stops and engine switch on (IG)

    HINT:
    The waveform varies depending on the CAN communication signal.

  15. A211721E01
    WAVEFORM 14:
    Crankshaft position sensor and camshaft position sensor 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    CH1: C46*1-110 (NE+) - C46*1-111 (NE-)
    CH1: C45*2-110 (NE+) - C45*2-111 (NE-)
    5 V/DIV., 20 msec./DIV.
    Idle after engine warmed up
    CH2: C46*1-90 (G2) - C46*1-89 (G2-)
    CH2: C45*2-90 (G2) - C45*2-89 (G2-)
    5 V/DIV., 20 msec./DIV.
    Idle after engine warmed up

    HINT:
    The wavelength becomes shorter as the engine rpm increases.

  16. A100214E06
    WAVEFORM 15:
    Terminal DI of air injection control driver 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    C46*1-30 (AIDI) - C46*1-81 (E1)
    C45*2-30 (AIDI) - C45*2-81 (E1)
    5 V/DIV., 50 msec./DIV.
    Performing system check using GTS (air injection check)

    HINT:
    The wavelength changes when the air injection control driver detects malfunctions in the air injection system (Click here).

  17. A217927E01
    WAVEFORM 16:
    Crankshaft position sensor and VVT sensor for exhaust side 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    (a) C46*1-110 (NE+) - C46*1-111 (NE-)
    (a) C45*2-110 (NE+) - C45*2-111 (NE-)
    5 V/DIV., 20 msec./DIV.
    Idle after engine warmed up
    (b) C46*1-69 (EV1+) - C46*1-68 (EV1-)
    (b) C45*2-69 (EV1+) - C45*2-68 (EV1-)
    5 V/DIV., 20 msec./DIV.
    Idle after engine warmed up
    (c) C46*1-64 (EV2+) - C46*1-65 (EV2-)
    (c) C45*2-64 (EV2+) - C45*2-65 (EV2-)
    5 V/DIV., 20 msec./DIV.
    Idle after engine warmed up

    HINT:
    The wavelength becomes shorter as engine rpm increases.

← PROBLEM SYMPTOMS TABLE (from Jan 2012)DIAGNOSIS SYSTEM (from Jan 2012) →