FREEZE FRAME DATA
Troubleshooting · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| DESCRIPTION |
- Freeze frame data records the engine conditions (fuel system, calculated load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when a malfunction is detected. When troubleshooting, it can help determine if the vehicle was running or stopped, the engine was warmed up or not, the air-fuel ratio was Lean or Rich, and other data from the time the malfunction occurred.
- HINT:
- If it is impossible to duplicate the problem even though a DTC is output, confirm the freeze frame data.
-
The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the intelligent tester, 5 separate sets of freeze frame data can be checked.

- 3 data sets before the DTC was stored.
- 1 data set when the DTC was stored.
- 1 data set after the DTC was stored.
- These data sets can be used to simulate the condition of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.
| LIST OF FREEZE FRAME DATA |
| Tester Display |
Measurement Item |
Diagnostic Note |
| Vehicle Speed |
Vehicle speed |
Speed indicated on speedometer. |
| Engine Speed |
Engine speed |
- |
| Calculate Load |
Calculated load |
Calculated load by ECM. |
| Vehicle Load |
Vehicle load |
- |
| MAF |
Mass air flow volume |
If approximately 0.0 gm/s:
|
| Atmosphere Pressure |
Atmosphere pressure |
- |
| Coolant Temp |
Engine coolant temperature |
If -40°C (-40°F), sensor circuit open. If 140°C (284°F) or more, sensor circuit shorted. |
| Intake Air |
Intake air temperature |
If -40°C (-40°F), sensor circuit open. If 140°C (284°F) or more, sensor circuit shorted. |
| Engine Run Time |
Accumulated engine running time |
- |
| Initial Engine Coolant Temp |
Engine coolant temperature at engine start |
- |
| Initial Intake Air Temp |
Intake air temperature at engine start |
- |
| Battery Voltage |
Battery voltage |
- |
| Accel Sens. No.1 Volt % |
Absolute Accelerator Pedal Position (APP) No. 1 |
- |
| Accel Sens. No.2 Volt % |
Absolute APP No. 2 |
- |
| Throttle Sensor Volt % |
Throttle sensor positioning |
- |
| Throttl Sensor #2 Volt % |
Throttle sensor positioning #2 |
- |
| Throttle Sensor Position |
Throttle position |
- |
| Throttle Motor DUTY |
Throttle motor |
- |
| Injector (Port) |
Injection period of No. 1 cylinder |
- |
| Injection Volum (Cylinder 1) |
Injection volume |
- |
| Fuel Pump/Speed Status |
Fuel pump/speed status |
- |
| EVAP (Purge) VSV |
EVAP purge VSV duty ratio |
- |
| Evap Purge Flow |
Ratio of evaporative purge flow to intake air volume |
- |
| Purge Density Learn Value |
Learning value of purge density |
- |
| EVAP Purge VSV |
EVAP Purge VSV |
- |
| Target Air-Fuel Ratio |
Ratio compared to stoichiometric level |
- |
| AF Lambda B1S1 |
Fuel trim at A/F sensor |
- |
| AF Lambda B2S1 |
Fuel trim at A/F sensor |
- |
| AFS Voltage B1S1 AFS Voltage B2S1 |
A/F sensor output |
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor. |
| AFS Current B1S1 |
A/F sensor current |
- |
| AFS Current B2S1 |
A/F sensor current |
- |
| O2S B1S2 O2S B2S2 |
Heated oxygen sensor output |
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor. |
| Short FT #1 |
Short-term fuel trim |
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio. |
| Long FT #1 |
Long-term fuel trim |
Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central value. |
| Total FT #1 |
Total fuel trim |
- |
| Short FT #2 |
Short-term fuel trim |
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio. |
| Long FT #2 |
Long-term fuel trim |
Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central value. |
| Total FT #2 |
Total fuel trim |
- |
| Fuel System Status #1 |
Fuel system status (for Bank 1) |
|
| Fuel System Status #2 |
Fuel system status (for Bank 2) |
|
| IGN Advance |
Ignition advance |
- |
| Knock Feedback Value |
Feedback value of knocking |
- |
| Knock Correct Learn Value |
Correction learning value of knocking |
- |
| ACIS VSV |
VSV for Acoustic Control Induction System (ACIS) |
- |
| VVT Control Status #1 |
VVT control status |
- |
| VVT Control Status #2 |
VVT control status |
- |
| Catalyst Temp B1S1 |
Estimated catalyst temperature (for Sensor 1) |
- |
| Catalyst Temp B2S1 |
Estimated catalyst temperature (for Sensor 1) |
- |
| Catalyst Temp B1S2 |
Estimated catalyst temperature (for Sensor 2) |
- |
| Catalyst Temp B2S2 |
Estimated catalyst temperature (for Sensor 2) |
- |
| Starter Signal |
Starter switch (STSW) signal |
- |
| Starter Control |
Starter switch status |
- |
| Power Steering Signal |
Power steering switch status |
- |
| Starter Relay |
Starter relay status |
- |
| Power Steer. Sig. Record |
Power steering signal (history) |
This signal status is usually ON until the cables are disconnected from the battery terminals. |
| ACC Relay |
ACC relay status |
- |
| Neutral Position SW Signal |
Park/Neutral position (PNP) switch signal |
- |
| Stop Light Switch |
Stop light switch |
- |
| A/C Signal |
A/C signal |
- |
| Closed Throttle Position SW |
Closed throttle position switch |
- |
| Fuel Cut Condition |
Fuel cut condition |
- |
| Immobiliser Communication |
Immobiliser communication |
- |
| Electrical Load Signal |
Electrical load signal |
- |
| Time after DTC Cleared |
Cumulative time after DTC cleared |
- |
| Distance from DTC Cleared |
Accumulated distance from DTC cleared |
- |
| Warmup Cycle Cleared DTC |
Warm-up cycle after DTC cleared |
- |
| TC and TE1 |
TC and CG (TE1) terminals of DLC3 |
- |
| Ignition Trig. Count |
Ignition counter |
- |
| Cylinder #1 Misfire Count |
Cylinder #1 misfire |
- |
| Cylinder #2 Misfire Count |
Cylinder #2 misfire |
- |
| Cylinder #3 Misfire Count |
Cylinder #3 misfire |
- |
| Cylinder #4 Misfire Count |
Cylinder #4 misfire |
- |
| Cylinder #5 Misfire Count |
Cylinder #5 misfire |
- |
| Cylinder #6 Misfire Count |
Cylinder #6 misfire |
- |
| Cylinder #7 Misfire Count |
Cylinder #7 misfire |
- |
| Cylinder #8 Misfire Count |
Cylinder #8 misfire |
- |
| All Cylinders Misfire Count |
All cylinders misfire |
- |
| Multi Cylinders Misfire Count |
Multiple cylinder misfire |
- |
| Misfire RPM |
Engine speed when misfire occurred |
- |
| Misfire Load |
Engine load when misfire occurred |
- |
| Misfire Margin |
Margin to detect engine misfire |
- |
| Catalyst OT MF F/C |
Catalyst over temperature misfire prevention F/C |
- |
| Cat OT MF F/C History |
Catalyst over temperature misfire prevention F/C history |
- |
| Cat OT MF F/C Cylinder#1 |
Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected) |
- |
| Cat OT MF F/C Cylinder#2 |
Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected) |
- |
| Cat OT MF F/C Cylinder#3 |
Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected) |
- |
| Cat OT MF F/C Cylinder#4 |
Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected) |
- |
| Cat OT MF F/C Cylinder#5 |
Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected) |
- |
| Cat OT MF F/C Cylinder#6 |
Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected) |
- |
| Cat OT MF F/C Cylinder#7 |
Display of fuel cut operation in No. 7 cylinder (if certain level of misfire malfunction is detected) |
- |
| Cat OT MF F/C Cylinder#8 |
Display of fuel cut operation in No. 8 cylinder (if certain level of misfire malfunction is detected) |
- |
| Power Steering Pressure |
Power steering pressure sensor |
- |
| ACT VSV |
A/C cut status for Active Test |
- |
| Idle Fuel Cut |
Fuel cut idle |
ON: when throttle valve fully closed and engine speed over 3500 rpm. |
| FC TAU |
Fuel cut during very light load |
Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete. |
| SPD (NT) |
Input shaft speed |
Data is displayed in increments of 50 rpm. |
| SPD (SP2) |
Output shaft speed |
- |