2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

FREEZE FRAME DATA

Troubleshooting · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


DESCRIPTION
  1. Freeze frame data records the engine conditions (fuel system, calculated load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when a malfunction is detected. When troubleshooting, it can help determine if the vehicle was moving or stationary, the engine was warmed up or not, the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

    HINT:
    If it is impossible to duplicate the problem even though a DTC is output, confirm the freeze frame data.


  1. A103809E31
    The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the intelligent tester, 5 separate sets of freeze frame data can be checked.
    1. 3 data sets before the DTC was stored.
    2. 1 data set when the DTC was stored.
    3. 1 data set after the DTC was stored.
    1. These data sets can be used to simulate the condition of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.

LIST OF FREEZE FRAME DATA
LABEL
(Tester Display)
Measurement Item
Diagnostic Note
Vehicle Speed
Vehicle speed
The speed indicated on the speedometer.
Engine Speed
Engine speed
-
Calculate Load
Calculated load
The load calculated by the ECM.
Vehicle Load
Vehicle load
-
MAF
Airflow rate from MAF meter
If the value is approximately 0.0 g/sec.:
  1. The mass air flow meter power source circuit is open or shorted.
  1. The VG circuit is open or shorted.
If the value is 160.0 g/sec. or more:
  1. The E2G circuit is open.
Atmosphere Pressure
Atmosphere pressure
-
Coolant Temp
Engine coolant temperature
If the value is -40°C (-40°F), the sensor circuit is open.
If the value is 140°C (284°F) or higher, the sensor circuit is shorted.
Intake Air
Intake air temperature
If the value is -40°C (-40°F), the sensor circuit is open.
If the value is 140°C (284°F) or higher, the sensor circuit is shorted.
Engine Run Time
Accumulated engine running time
-
Initial Engine Coolant Temp
Initial engine coolant temperature
-
Initial Intake Air Temp
Initial intake air temperature
-
Battery Voltage
Battery voltage
-
Accel Sens. No.1 Volt %
Absolute Accelerator Pedal Position (APP) No. 1
-
Accel Sens. No.2 Volt %
Absolute APP No. 2
-
Throttle Sensor Volt %
Absolute throttle position
-
Throttl Sensor #2 Volt %
Absolute throttle sensor positioning #2
-
Throttle Sensor Position
Throttle sensor positioning
-
Throttle Motor DUTY
Throttle actuator
-
Injector (Port)
Injection period of No. 1 cylinder
-
Injection Volum (Cylinder1)
Injection volume
-
Fuel Pump/Speed Status
Fuel pump/speed status
-
EVAP (Purge) VSV
EVAP purge VSV duty ratio
-
Evap Purge Flow
Ratio of evaporative purge flow to intake air volume
-
Purge Density Learn Value
Learning value of purge density
-
EVAP Purge VSV
EVAP purge VSV
-
Target Air-Fuel Ratio
Ratio compared to stoichiometric level
-
AF Lambda B1S1
Fuel trim at A/F sensor (bank 1 sensor 1)
-
AF Lambda B2S1
Fuel trim at A/F sensor (bank 2 sensor 1)
-
AFS Voltage B1S1
Air fuel ratio (A/F) sensor output voltage
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
AFS Voltage B2S1
A/F sensor output voltage
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
AFS Current B1S1
A/F sensor current (bank 1 sensor 1)
-
AFS Current B2S1
A/F sensor current
-
O2S B1S2
Heated oxygen sensor output voltage
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
O2S B2S2
Heated oxygen sensor output voltage
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
Short FT #1
Short-term fuel trim
Short-term fuel compensation is used to maintain the air fuel ratio at the stoichiometric air fuel ratio.
Long FT #1
Long-term fuel trim
Overall fuel compensation is carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
Total FT #1
Total fuel trim
-
Short FT #2
Short-term fuel trim
Short-term fuel compensation is used to maintain the air fuel ratio at the stoichiometric air fuel ratio.
Long FT #2
Long-term fuel trim
Overall fuel compensation is carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
Total FT #2
Total fuel trim
-
Fuel System Status #1
Fuel system status (bank 1)
  1. OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
  2. CL (Closed Loop): Using the heated oxygen sensor as feedback for fuel control.
  3. OLDrive: Open loop due to driving conditions (fuel enrichment).
  4. OLFault: Open loop due to a detected system fault.
  5. CLFault: Closed loop but the heated oxygen sensor, which is used for fuel control, is malfunctioning.
Fuel System Status #2
Fuel system status (bank 2)
  1. OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
  2. CL (Closed Loop): Using the heated oxygen sensor as feedback for fuel control.
  3. OLDrive: Open loop due to driving conditions (fuel enrichment).
  4. OLFault: Open loop due to a detected system fault.
  5. CLFault: Closed loop but the heated oxygen sensor, which is used for fuel control, is malfunctioning.
IGN Advance
Ignition advance
-
Knock Feedback Value
Feedback value of knocking
-
Knock Correct Learn Value
Correction learning value of knocking
-
ACIS VSV
VSV for Acoustic Control Induction System (ACIS)
-
VVT Control Status #1
VVT control status
-
VVT Control Status #2
VVT control status
-
Catalyst Temp B1S1
Estimated catalyst temperature (bank 1 sensor 1)
-
Catalyst Temp B2S1
Estimated catalyst temperature (bank 2 sensor 1)
-
Catalyst Temp B1S2
Estimated catalyst temperature (bank 1 sensor 2)
-
Catalyst Temp B2S2
Estimated catalyst temperature (bank 2 sensor 2)
-
Starter Signal
Starter switch signal
-
Starter Control
Starter switch status
-
Power Steering Signal Record
Power steering switch
-
Starter Relay
Starter relay status
-
Power Steer. Sig. Record
Power steering signal (history)
-
ACC Relay
ACC relay status
-
Neutral Position SW Signal
Park/Neutral Position (PNP) switch signal
-
Stop Light Switch
Stop light switch
-
A/C Signal
A/C signal
-
Closed Throttle Position SW
Closed throttle position switch
-
Fuel Cut Condition
Fuel cut condition
-
Immobiliser Communication
Immobiliser communication
-
Electrical Load Signal
Electrical load signal
-
Time after DTC Cleared
Cumulative time after DTC cleared
-
Distance from DTC Cleared
Accumulated distance from DTC cleared
-
Warmup Cycle Cleared DTC
Warm-up cycle after DTC cleared
-
TC and TE1
TC and CG (TE1) terminals of DLC3
-
Ignition Trig. Count
Ignition
-
Cylinder #1 Misfire Count
Cylinder #1 misfire count
Displayed only while idling.
Cylinder #2 Misfire Count
Cylinder #2 misfire count
Displayed only while idling.
Cylinder #3 Misfire Count
Cylinder #3 misfire count
Displayed only while idling.
Cylinder #4 Misfire Count
Cylinder #4 misfire count
Displayed only while idling.
Cylinder #5 Misfire Count
Cylinder #5 misfire count
Displayed only while idling.
Cylinder #6 Misfire Count
Cylinder #6 misfire count
Displayed only while idling.
All Cylinders Misfire Count
All cylinders misfire count
Displayed only while idling.
Misfire RPM
Misfire RPM
-
Misfire Load
Misfire load
-
Misfire Margin
Misfire monitoring
-
ACT VSV
A/C cut status for Active Test
-
Idle Fuel Cut
Fuel cut idle
ON: when the throttle valve is fully closed and the engine speed is more than 3500 rpm.
FC TAU
Fuel cut during very light load
Fuel cut is being performed under a very light load to prevent the engine combustion from becoming incomplete.
← DTC CHECK / CLEAR (from Jan 2012)FREEZE FRAME DATA (from Jan 2012) →