2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

FREEZE FRAME DATA

Troubleshooting · Vehicles built Sep 2011 – Dec 2011


DESCRIPTION
  1. Freeze frame data records the engine conditions (fuel system, calculated load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when a malfunction is detected. When troubleshooting, it can help determine if the vehicle was running or stopped, the engine was warmed up or not, the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

    HINT:
    If it is impossible to duplicate the problem even though a DTC is stored, confirm the freeze frame data.


  1. A103809E32
    The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the intelligent tester, 5 separate sets of freeze frame data can be checked.
    1. 3 data sets before the DTC was stored.
    2. 1 data set when the DTC was stored.
    3. 1 data set after the DTC was stored.
    1. These data sets can be used to simulate the condition of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.

LIST OF FREEZE FRAME DATA
LABEL
(Tester Display)
Measurement Item
Diagnostic Note
Trouble Code
Trouble code
-
Injector (port)
Injection period of No. 1 cylinder
-
IGN Advance
Ignition advance
-
Calculate Load
Calculated load
The load calculated by the ECM.
Vehicle Load
Vehicle load
-
MAF
Mass air flow volume
If the value is approximately 0.0 g/sec.:
  1. The mass air flow meter power source circuit is open or shorted.
  2. The VG circuit is open or shorted.
If the value is 160.0 g/sec. or more:
  1. The E2G circuit is open.
Engine Speed
Engine speed
-
Vehicle Speed
Vehicle speed
The speed indicated on the speedometer.
Coolant Temp
Engine coolant temperature
If the value is -40°C (-40°F), the sensor circuit is open.
If the value is 140°C (284°F) or higher, the sensor circuit is shorted.
Intake Air
Intake air temperature
If the value is -40°C (-40°F), the sensor circuit is open.
If the value is 140°C (284°F) or higher, the sensor circuit is shorted.
2nd Air System Status
Second air system status
-
Air-Fuel Ratio
Ratio compared to stoichiometric level
-
Purge Density Learn Value
Learning value of purge density
-
Evap Purge Flow
Ratio of evaporative purge flow to intake air volume
-
EVAP (Purge) VSV
EVAP purge VSV duty ratio
-
Knock Correct Learn Value
Correction learning value of knocking
-
Knock Feedback Value
Feedback value of knocking
-
Accelerator Position No.1
Absolute Accelerator Pedal Position (APP) No. 1
-
Accelerator Position No.2
Absolute APP No. 2
-
Throttle Position
Throttle position
-
Throttle Sensor Position
Throttle sensor positioning
-
Throttle Sensor Position #2
Throttle sensor positioning #2
-
Throttle Motor
Throttle motor
-
O2S B1 S2
O2S B2 S2
Heated oxygen sensor output
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
AFS B1 S1
AFS B2 S1
A/F sensor output
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
AFS B2 S1
A/F sensor current
-
Total FT #1
Total FT #2
Total fuel trim
-
Short FT #1
Short-term fuel trim
Short-term fuel compensation is used to maintain the air-fuel ratio at the stoichiometric air-fuel ratio.
Long FT #1
Long-term fuel trim
Overall fuel compensation is carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
Short FT #2
Short-term fuel trim
Short-term fuel compensation is used to maintain the air-fuel ratio at the stoichiometric air-fuel ratio.
Long FT #2
Long-term fuel trim
Overall fuel compensation is carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
Fuel System Status (Bank1)
Fuel system status (for Bank 1)
  1. OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
  2. CL (Closed Loop): Using the heated oxygen sensor as feedback for fuel control.
  3. OLDrive: Open loop due to driving conditions (fuel enrichment).
  4. OLFault: Open loop due to a detected system fault.
  5. CLFault: Closed loop but the heated oxygen sensor, which is used for fuel control, is malfunctioning.
Fuel System Status (Bank2)
Fuel system status (for Bank 2)
  1. OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
  2. CL (Closed Loop): Using the heated oxygen sensor as feedback for fuel control.
  3. OLDrive: Open loop due to driving conditions (fuel enrichment).
  4. OLFault: Open loop due to a detected system fault.
  5. CLFault: Closed loop but the heated oxygen sensor, which is used for fuel control, is malfunctioning.
O2FT B1 S2
O2FT B2 S2
Fuel trim at heated oxygen sensor
-
AF FT B1 S1
Fuel trim at A/F sensor
-
AFS B1 S1
A/F sensor current
-
AF FT B2 S1
Fuel trim at A/F sensor
-
Catalyst Temp (B1 S1)
Catalyst Temp (B2 S1)
Estimated catalyst temperature (for Sensor 1)
-
Catalyst Temp (B1 S2)
Catalyst Temp (B2 S2)
Estimated catalyst temperature (for Sensor 2)
-
Initial Engine Coolant Temp
Engine coolant temperature at engine start
-
Initial Intake Air Temp
Intake air temperature at engine start
-
Injection Volum (Cylinder1)
Injection volume
-
Air pump pressure (absolute)
Air pump pressure
-
Air Pump Pulsation Pressure
Air pump pulsation pressure
-
Power Steering Pressure
Power steering pressure sensor
-
ACC Relay
ACC relay status
-
Starter Relay
Starter relay status
-
Starter Signal
Starter switch (STSW) signal
-
Starter Control
Starter switch status
-
Power Steering Switch
Power steering switch status
-
Power Steering Signal
Power steering signal status
-
Closed Throttle Position SW
Closed throttle position switch
-
A/C Signal
A/C signal
-
Neutral Position SW Signal
Park/Neutral Position (PNP) switch signal
-
Electrical Load Signal
Electrical load signal
-
Stop Light Switch
Stop light switch
-
Immobiliser Communication
Immobiliser communication
-
Fuel Cut Condition
Fuel cut condition
-
Battery Voltage
Battery voltage
-
Atmosphere Pressure
Atmospheric pressure
-
Secondary Air Control VSV
Secondary air injection system status
-
ACIS VSV
VSV for Acoustic Control Induction System (ACIS)
-
ACT VSV
A/C cut status for Active Test
-
VVT Control Status (Bank2)
VVT control status
-
EVAP Purge VSV
EVAP purge VSV
-
Fuel Pump/Speed Status
Fuel pump/speed status
-
VVT Control Status (Bank1)
VVT control status
-
TC and TE1
TC and CG (TE1) terminals of DLC3
-
AI Test
AI test status
-
Engine Speed of Cyl #1
Engine speed during No. 1 cylinder fuel cut
-
Engine Speed of Cyl #2
Engine speed during No. 2 cylinder fuel cut
-
Engine Speed of Cyl #3
Engine speed during No. 3 cylinder fuel cut
-
Engine Speed of Cyl #4
Engine speed during No. 4 cylinder fuel cut
-
Engine Speed of Cyl #5
Engine speed during No. 5 cylinder fuel cut
-
Engine Speed of Cyl #6
Engine speed during No. 6 cylinder fuel cut
-
Engine Speed of Cyl #7
Engine speed during No. 7 cylinder fuel cut
-
Engine Speed of Cyl #8
Engine speed during No. 8 cylinder fuel cut
-
VVT Aim Angle (Bank1)
VVT aim angle
-
VVT Change Angle (Bank1)
VVT change angle
-
VVT OCV Duty (Bank1)
VVT OCV operation duty
-
VVT Aim Angle (Bank2)
VVT aim angle
-
VVT Change Angle (Bank2)
VVT change angle
-
VVT OCV Duty (Bank2)
VVT OCV operation duty
-
Idle Fuel Cut
Fuel cut idle
ON: when the throttle valve is fully closed and the engine speed is more than 3500 rpm.
FC TAU
Fuel cut during very light load
Fuel cut is being performed under a very light load to prevent the engine combustion from becoming incomplete.
Ignition
Ignition counter
-
Cylinder #1 Misfire Count
Cylinder #1 misfire
Only displayed during idling.
Cylinder #2 Misfire Count
Cylinder #2 misfire
Only displayed during idling.
Cylinder #3 Misfire Count
Cylinder #3 misfire
Only displayed during idling.
Cylinder #4 Misfire Count
Cylinder #4 misfire
Only displayed during idling.
Cylinder #5 Misfire Count
Cylinder #5 misfire
Only displayed during idling.
Cylinder #6 Misfire Count
Cylinder #6 misfire
Only displayed during idling.
Cylinder #7 Misfire Count
Cylinder #7 misfire
Only displayed during idling.
Cylinder #8 Misfire Count
Cylinder #8 misfire
Only displayed during idling.
All Cylinders Misfire Count
All cylinders misfire
Only displayed during idling.
Multi Cylinders Misfire Count
Multiple cylinder misfire
-
Misfire RPM
Engine speed when misfire occurred
-
Misfire Load
Engine load when misfire occurred
-
Misfire Margin
Margin to detect engine misfire
-
Engine Run Time
Accumulated engine running time
-
Time after DTC Cleared
Cumulative time after DTC cleared
-
Distance from DTC Cleared
Accumulated distance from DTC cleared
-
Warmup Cycle Cleared DTC
Warm-up cycle after DTC cleared
-
← DTC CHECK / CLEAR (Sep 2011 – Dec 2011)CHECK MODE PROCEDURE (Sep 2011 – Dec 2011) →