TERMINALS OF ECU
System information · Vehicles built from Jan 2012
| CHECK ECM (for 1UR-FE) |


- HINT:
- As the ECM connector is a waterproof connector, it is not possible to check the voltage of each terminal or check the waveform with an oscilloscope while the ECM is installed in the vehicle.
Disconnect the A38*1 and C45*1 or A52*2 and C46*2 ECM connectors.
- *1: for LHD
- *2: for RHD
- *1: for LHD
Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A38*1-16 (TC) - Body ground
A52*2-16 (TC) - Body ground
V-W - Body ground
Terminal TC of DLC3
Engine switch on (IG)
11 to 14 V
Engine switch off
Below 1 V
C45*1-81 (E1) - Body ground
C46*2-81 (E1) - Body ground
BR - Body ground
ECM ground
Always
Below 1 Ω
C45*1-27 (D) - Body ground
C46*2-27 (D) - Body ground
G - Body ground
Park/neutral position switch signal
Engine switch on (IG)
Shift lever in D
11 to 14 V
Engine switch on (IG)
Shift lever not in D
Below 1 V
A38*1-38 (SFTU) - Body ground
A52*2-38 (SFTU) - Body ground
Y - Body ground
Park/neutral position switch signal
Engine switch on (IG)
Shift lever in S
Below 1 Ω
Engine switch on (IG)
Shift lever in +
10 kΩ or higher
A38*1-25 (S) - Body ground
A52*2-25 (S) - Body ground
W - Body ground
Park/neutral position switch signal
Engine switch on (IG)
Shift lever in S
11 to 14 V
Engine switch on (IG)
Shift lever not in S
Below 1 V
A38*1-27 (SFTD) - Body ground
A52*2-27 (SFTD) - Body ground
L - Body ground
Park/neutral position switch signal
Engine switch on (IG)
Shift lever in S
10 kΩ or higher
Engine switch on (IG)
Shift lever in -
Below 1 Ω
A38*1-36 (STP) - Body ground
A52*2-36 (STP) - Body ground
R - Body ground
Stop light signal
Engine switch on (IG)
Brake pedal depressed
11 to 14 V
Engine switch on (IG)
Brake pedal released
Below 1 V
A38*1-35 (ST1-) - Body ground
A52*2-35 (ST1-) - Body ground
R-W - Body ground
Stop light signal (opposite to STP terminal)
Engine switch on (IG)
Brake pedal depressed
Below 1 V
Engine switch on (IG)
Brake pedal released
11 to 14 V
A38*1-45 (CCS) - Body ground
A52*2-45 (CCS) - Body ground
L - Body ground
Cruise control main switch signal
Engine switch on (IG)
Main switch off
1 MΩ or higher
Engine switch on (IG)
CANCEL switch held on
1510 to 1570 Ω
Engine switch on (IG)
-SET switch held on
620 to 640 Ω
Engine switch on (IG)
+RES switch held on
235 to 245 Ω
Engine switch on (IG)
Main switch on
Below 2.5 Ω
A38*1-37 (CCHG) - Body ground
A52*2-37 (CCHG) - Body ground
P-B - Body ground
Distance control switch signal
Engine switch on (IG)
Main switch on
MODE switch held on
Below 1 V
Engine switch on (IG)
Main switch on
MODE switch off
11 to 14 V
- *1: for LHD
- *2: for RHD
- *1: for LHD
| CHECK ECM (for 3UR-FE) |


- HINT:
- As the ECM connector is a waterproof connector, it is not possible to check the voltage of each terminal or check the waveform with an oscilloscope while the ECM is installed in the vehicle.
Disconnect the A38 and C45 ECM connectors.
Measure the voltage and resistance according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A38-16 (TC) - Body ground
V-W - Body ground
Terminal TC of DLC3
Engine switch on (IG)
11 to 14 V
Engine switch off
Below 1 V
C45-81 (E1) - Body ground
W-B - Body ground
ECM ground
Always
Below 1 Ω
C45-27 (D) - Body ground
G - Body ground
Park/neutral position switch signal
Engine switch on (IG)
Shift lever in D
11 to 14 V
Engine switch on (IG)
Shift lever not in D
Below 1 V
A38-38 (SFTU) - Body ground
Y - Body ground
Park/neutral position switch signal
Engine switch on (IG)
Shift lever in S
Below 1 Ω
Engine switch on (IG)
Shift lever in +
10 kΩ or higher
A38-25 (S) - Body ground
W - Body ground
Park/neutral position switch signal
Engine switch on (IG)
Shift lever in S
11 to 14 V
Engine switch on (IG)
Shift lever not in S
Below 1 V
A38-27 (SFTD) - Body ground
L - Body ground
Park/neutral position switch signal
Engine switch on (IG)
Shift lever in S
10 kΩ or higher
Engine switch on (IG)
Shift lever in -
Below 1 Ω
A38-36 (STP) - Body ground
R - Body ground
Stop light signal
Engine switch on (IG)
Brake pedal depressed
11 to 14 V
Engine switch on (IG)
Brake pedal released
Below 1 V
A38-35 (ST1-) - Body ground
R-W - Body ground
Stop light signal (opposite to STP terminal)
Engine switch on (IG)
Brake pedal depressed
Below 1 V
Engine switch on (IG)
Brake pedal released
11 to 14 V
A38-45 (CCS) - Body ground
L - Body ground
Cruise control main switch signal
Engine switch on (IG)
Main switch off
1 MΩ or higher
Engine switch on (IG)
CANCEL switch held on
1510 to 1570 Ω
Engine switch on (IG)
-SET switch held on
620 to 640 Ω
Engine switch on (IG)
+RES switch held on
235 to 245 Ω
Engine switch on (IG)
Main switch on
Below 2.5 Ω
A38-37 (CCHG) - Body ground
P-B - Body ground
Distance control switch signal
Engine switch on (IG)
Main switch on
MODE switch held on
Below 1 V
Engine switch on (IG)
Main switch on
MODE switch off
11 to 14 V
| CHECK DISTANCE CONTROL ECU |


Disconnect the E108 distance control ECU connector.
Measure the voltage and resistance according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E108-1 (B) - Body ground
R - Body ground
Distance control ECU power source line
Engine switch on (IG)
11 to 14 V
E108-3 (WASH) - Body ground
L - Body ground
Windshield wiper switch signal
Engine switch on (IG)
Windshield wiper switch on
11 to 14 V
Engine switch on (IG)
Windshield wiper switch off
Below 1 V
E108-12 (GND) - Body ground
BR - Body ground
Ground
Always
Below 1 Ω
E108-13 (IGB) - Body ground
R - Body ground
Engine switch on (IG) signal
Engine switch on (IG)
11 to 14 V
Engine switch off
Below 1 V
E108-16 (MODE) - Body ground
W - Body ground
Distance control switch signal
Engine switch on (IG)
Distance control switch on
Below 1 V
Engine switch on (IG)
Distance control switch off
11 to 14 V
E108-22 (LRDD) - E108-10 (SGND)
B - R
Millimeter wave radar sensor input signal
Engine switch on (IG)
Pulse generation
(See waveform 1)
E108-23 (LRRD) - E108-10 (SGND)
W - R
Millimeter wave radar sensor output signal
Engine switch on (IG)
Pulse generation
(See waveform 2)
Using an oscilloscope, check waveform 1.

Item
Content
Terminal No. (Symbol)
E108-22 (LRDD) - E108-10 (SGND)
Tool Setting
2 V/DIV., 10 msec./DIV.
Condition
Engine switch on (IG)
Using an oscilloscope, check waveform 2.

Item
Content
Terminal No. (Symbol)
E108-23 (LRRD) - E108-10 (SGND)
Tool Setting
2 V/DIV., 5 msec./DIV.
Condition
Engine switch on (IG)
| CHECK MILLIMETER WAVE RADAR SENSOR |


Disconnect the A56 millimeter wave radar sensor connector.
Measure the voltage according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A56-3 (LRDD) - A56-2 (SGND)
B - R-W
Millimeter wave radar sensor output signal
Engine switch on (IG)
Pulse generation
(See waveform 3)
A56-4 (LRRD) - A56-2 (SGND)
W - R-W
Millimeter wave radar sensor input signal
Engine switch on (IG)
Pulse generation
(See waveform 4)
A56-5 (IGB) - A56-2 (SGND)
R-B - R-W
Engine switch on (IG) signal
Engine switch on (IG)
11 to 14 V
Engine switch off
Below 1 V
Using an oscilloscope, check waveform 3.

Item
Content
Terminal No. (Symbol)
A56-3 (LRDD) - A56-2 (SGND)
Tool Setting
2 V/DIV., 10 msec./DIV.
Condition
Engine switch on (IG)
Using an oscilloscope, check waveform 4.

Item
Content
Terminal No. (Symbol)
A56-4 (LRRD) - A56-2 (SGND)
Tool Setting
2 V/DIV., 5 msec./DIV.
Condition
Engine switch on (IG)