2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

HOW TO PROCEED WITH TROUBLESHOOTING

Troubleshooting · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the following procedure to troubleshoot the audio and visual system.
  2. *: Use the intelligent tester.


1.VEHICLE BROUGHT TO WORKSHOP
    NEXT

    2.INSPECT BATTERY VOLTAGE

      Standard Voltage:
      11 to 14 V

      1. If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
    NEXT

    3.BASIC INSPECTION
    1. Turn the engine switch on (IG).

    2. Check whether or not the radio receiver assembly turns on.

      Result 
      Result
      Proceed to
      Radio receiver assembly turns on.
      A
      Radio receiver assembly does not turn on.
      B


    B.
    A

    4.CHECK FOR DTC*
    1. Refer to DTC Check/Clear of the navigation system.

      1. Refer to Navigation System (for HDD) (Click here).
      2. Refer to Navigation System (for DVD) (Click here).
      Result 
      Result
      Proceed to
      DTC is output.
      A
      DTC is not output.
      B

      HINT:
      After the check using the intelligent tester, check the "System Check Mode" screen as necessary.


    B.
    A

    5.DTC CLEAR*
    1. Refer to DTC Check/Clear of the navigation system.

      1. Refer to Navigation System (for HDD) (Click here).
      2. Refer to Navigation System (for DVD) (Click here).

      HINT:
      The present DTCs may not indicate actual malfunctions depending on the vehicle operating conditions.

    NEXT

    6.RECHECK FOR DTC*
    1. Refer to DTC Check/Clear of the navigation system.

      1. Refer to Navigation System (for HDD) (Click here).
      2. Refer to Navigation System (for DVD) (Click here).
      Result 
      Result
      Proceed to
      DTC is output.
      A
      DTC is not output.
      B

    2. HINT:
      1. Even if the malfunction symptom is not confirmed, check for diagnostic trouble codes. This is because the system stores past diagnostic trouble codes.
      2. After the check using the intelligent tester, check the "System Check Mode" screen as necessary.
      3. Check the diagnostic trouble code and inspect the area code indicates.


    B.
    A

    7.DIAGNOSTIC TROUBLE CODE CHART
    1. Find the output code in Diagnostic Trouble Code Chart (Click here).

      NOTICE:
      1. The navigation system outputs DTCs for the following systems.
      2. When DTCs other than the codes in Diagnostic Trouble Code Chart for the audio and visual system are output, refer to Diagnostic Trouble Code Chart for the following systems.
      3. Refer to Navigation System (for HDD) (Click here).
      4. Refer to Navigation System (for DVD) (Click here).

      Result 
      Result
      Proceed to
      Audio and Visual System (w/ Navigation System) are output.
      A
      Navigation System (for HDD) are output.
      B
      Navigation System (for DVD) are output.
      C


    A.

    B.

    C.
    8.PROBLEM SYMPTOMS TABLE
    1. Refer to Problem Symptoms Table (Click here).

      Result 
      Result
      Proceed to
      Fault is not listed in Problem Symptoms Table.
      A
      Fault is listed in Problem Symptoms Table.
      B

      HINT:
      If the symptom does not recur and no DTC is output, perform the symptom reproduction method (Click here).


    B.
    A

    9.CHECK ECU TERMINAL ARRANGEMENT BASED ON MALFUNCTION SYMPTOM
    1. Refer to Terminals of ECU (Click here).

    NEXT

    10.CHECK CIRCUIT
    1. Adjust, repair or replace as necessary.

    NEXT

    11.RECHECK FOR DIAGNOSTIC TROUBLE CODE

      HINT:
      After clearing DTCs, recheck for DTCs.

    NEXT

    12.PERFORM CONFIRMATION TEST
      NEXT

      ← SYSTEM DESCRIPTION (from Jan 2012)HOW TO PROCEED WITH TROUBLESHOOTING (from Jan 2012) →