TERMINALS OF ECU
System information · Vehicles built from Sep 2011
| CHECK ENGINE SWITCH |


Disconnect the E18 switch connector.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E18-5 (GND) - Body ground
BR - Body ground
Ground
Always
Below 1 Ω
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the E18 switch connector.
Measure the resistance and voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E18-8 (AGND) - Body ground
L - Body ground
Ground
Always
Below 1 Ω
E18-14 (VC5) - E18-8 (AGND)
P - L
Power supply
Key not in cabin
Below 1 V
Engine switch pressed*
4.6 to 5.4 V
E18-10 (CODE) - E18-8 (AGND)
G - L
Demodulated signal of key code output
Key not in cabin
Below 1 V
Engine switch pressed and key held close to engine switch*
Pulse generation (see waveform 1)
E18-9 (TXCT) - E18-8 (AGND)
SB - L
Key code input signal
Key not in cabin
Below 1 V
Engine switch pressed and key held close to engine switch*
Pulse generation (see waveform 2)
- HINT:
- *: Remove the key battery before performing this inspection.
- If the result is not as specified, the switch may have a malfunction.
Using an oscilloscope, check waveform 1.

Waveform 1 (Reference) Item
Content
Terminal No. (Symbol)
E18-10 (CODE) - E18-8 (AGND)
Tool Setting
2 V/DIV., 20 msec./DIV.
Condition
Engine switch pressed and key held close to engine switch*
- HINT:
- *: Remove the key battery before performing this inspection.
Using an oscilloscope, check waveform 2.

Waveform 2 (Reference) Item
Content
Terminal No. (Symbol)
E18-9 (TXCT) - E18-8 (AGND)
Tool Setting
2 V/DIV., 20 msec./DIV.
Condition
Engine switch pressed and key held close to engine switch*
- HINT:
- *: Remove the key battery before performing this inspection.
| CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |


Disconnect the E29 ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E29 -17 (E) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
E29-1 (+B) - E29-17 (E)
B - W-B
+B power supply
Always
11 to 14 V
E29-18 (IG) - E29-17 (E)
B - W-B
Ignition power supply
Engine switch off
Below 1 V
Engine switch on
11 to 14 V
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the E29 ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E29-40 (AGND) - Body ground
L - Body ground
Engine switch ground
Always
Below 1 Ω
E29-30 (VC5) - E29-40 (AGND)
P - L
Engine switch power supply
Key not in cabin
Below 1 V
Engine switch pressed*
4.6 to 5.4 V
E29-9 (CODE) - E29-40 (AGND)
G- L
Engine switch CODE input
Key not in cabin
Below 1 V
Engine switch pressed and key held close to engine switch*
Pulse generation (see waveform 1)
E29-8 (TXCT) - E29-40 (AGND)
SB - L
Engine switch TX output
Key not in cabin
Below 1 V
Engine switch pressed and key held close to engine switch*
Pulse generation (see waveform 2)
- HINT:
- *: Remove the key battery before performing this inspection.
- If the result is not as specified, the ECU may have a malfunction.
Using an oscilloscope, check waveform 1.

Waveform 1 (Reference) Item
Content
Terminal No. (Symbol)
E29-9 (CODE) - E29-40 (AGND)
Tool Setting
2 V/DIV., 20 msec./DIV.
Condition
Engine switch pressed and key held close to engine switch*
- HINT:
- *: Remove the key battery before performing this inspection.
Using an oscilloscope, check waveform 2.

Waveform 2 (Reference) Item
Content
Terminal No. (Symbol)
E29-8 (TXCT) - E29-40 (AGND)
Tool Setting
2 V/DIV., 20 msec./DIV.
Condition
Engine switch pressed and key held close to engine switch*
- HINT:
- *: Remove the key battery before performing this inspection.
| CHECK ID CODE BOX (IMMOBILISER CODE ECU) |


Disconnect the E28 box connector.
Measure the resistance and voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E28-8 (GND) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
E28-1 (+B) - E28-8 (GND)
B - W-B
+B power supply
Always
11 to 14 V
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the E28 box connector.
Measure the voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E28-5 (EFII) - E28-8 (GND)
W - W-B
ECM input signal
Engine switch off
Below 1 V
Engine switch on (IG)
Pulse generation (see waveform 1)
E28-6 (EFIO) - E28-8 (GND)
R - W-B
ECM output signal
Engine switch off
Below 1 V
Engine switch on (IG)
Pulse generation (see waveform 2)
- If the result is not as specified, the ID code box (immobiliser code ECU) may have a malfunction.
- If the result is not as specified, the ID code box (immobiliser code ECU) may have a malfunction.
Using an oscilloscope, check waveform 1.

Waveform 1 (Reference) Item
Content
Terminal No. (Symbol)
E28-5 (EFII) - E28-8 (GND)
Tool Setting
10 V/DIV., 100 msec./DIV.
Condition
Engine switch on (IG)
Using an oscilloscope, check waveform 2.

Waveform 2 (Reference) Item
Content
Terminal No. (Symbol)
E28-6 (EFIO) - E28-8 (GND)
Tool Setting
10 V/DIV., 100 msec./DIV.
Condition
Engine switch on (IG)
| CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) |


Disconnect the 2D and 2A ECU connectors.
Measure the resistance and voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
2D-62 (GND2) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
2D-8 (ACC) - 2D-62 (GND2)
GR - W-B
ACC power supply
Engine switch off
Below 1 V
Engine switch on (ACC)
11 to 14 V
2A-1 (IG) - 2D-62 (GND2)
B - W-B
IG power supply
Engine switch off
Below 1 V
Engine switch on (IG)
11 to 14 V
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
| CHECK STEERING LOCK ACTUATOR (STEERING LOCK ECU) |


Disconnect the E26 ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E26-2 (SGND) - Body ground
BR - Body ground
Ground
Always
Below 1 Ω
E26-1 (GND) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
E26-7 (B) - Body ground
R - Body ground
+B power supply
Always
11 to 14 V
E26-6 (IG2) - Body ground
B - Body ground
Ignition power supply
Engine switch off
Below 1 V
Engine switch on (IG)
11 to 14 V
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.