2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

INSPECTION

Inspection · Vehicles built Sep 2011 – Dec 2011


INSPECT CYLINDER BLOCK SUB-ASSEMBLY

  1. A004849E01
    Clean the cylinder block.

    1. Using a gasket scraper, remove all the gasket material from the top surface of the cylinder block.

    2. Using a soft brush and solvent, thoroughly clean the cylinder block.

      NOTICE:
      If the cylinder is washed at high temperatures, the cylinder liner sticks out beyond the cylinder block. Always wash the cylinder block at a temperature of 45°C (113°F) or less.

  1. A074955E03
    Using a precision straightedge and feeler gauge, measure the surfaces contacting the cylinder head and main bearing cap for warpage.

    Standard warpage:
    0 to 0.05 mm (0 to 0.00197 in.)

    Maximum warpage:
    0.07 mm (0.00276 in.)

    If the warpage is more than the maximum, replace the cylinder block.

  1. A004853E01
    Visually check the cylinder for vertical scratches.
    If deep scratches are present, rebore all 8 cylinders and replace all 8 pistons. If necessary, replace the cylinder block.


INSPECT CYLINDER BORE

HINT:
A116070E03
There are 3 standard cylinder bore diameter sizes, marked "1", "2" and "3" accordingly. The mark is stamped on the top of the cylinder block.

  1. Inspect the cylinder bore diameter.

    1. A005181E04
      Using a cylinder gauge, measure the cylinder bore diameter at positions A, B and C in the thrust and axial directions.

      Measurement Cylinder Bore Position:
      Position
      Specified Condition
      A
      10 mm (0.394 in.) from top edge
      B
      Center
      C
      10 mm (0.394 in.) from bottom edge

      Standard Diameter:
      Number Mark
      Specified Condition
      Mark 1
      94.002 to 94.010 mm (3.70087 to 3.70118 in.)
      Mark 2
      94.011 to 94.020 mm (3.70122 to 3.70157 in.)
      Mark 3
      94.021 to 94.028 mm (3.70161 to 3.70189 in.)

      Maximum diameter:
      94.230 mm (3.71 in.)

      If the diameter is more than the maximum, rebore all 8 cylinders and replace all 8 pistons. If necessary, replace the cylinder block.


INSPECT PISTON SUB-ASSEMBLY WITH PIN

  1. Clean the piston.

    1. A004877E01
      Using a gasket scraper, remove the carbon from the piston top.

    2. A004878E01
      Using a groove cleaning tool or broken ring, clean the piston ring grooves.

    3. A004879E01
      Using solvent and a brush, thoroughly clean the piston.

      NOTICE:
      Do not use a wire brush.

  1. Inspect the piston diameter.

    1. A160815E01
      A175228E01
      Using a micrometer, measure the piston diameter at a position that is 6.7 mm (0.264 in.) downward from the center of the piston pin hole (refer to the illustration).

      Standard Piston Diameter:
      Piston
      Specified Condition
      STD
      93.968 to 93.996 mm (3.670 to 3.701 in.)
      O/S (0.50)
      94.468 to 94.496 mm (3.719 to 3.720 in.)

      HINT:
      There are 3 standard diameter sizes, marked "1", "2" and "3". The mark is stamped on the piston top.

      Standard Piston Diameter:
      Number Mark
      Specified Condition
      Mark 1
      93.942 to 93.952 mm (3.6985 to 3.6989 in.)
      Mark 2
      93.952 to 93.960 mm (3.6989 to 3.6992 in.)
      Mark 3
      93.960 to 93.970 mm (3.6992 to 3.6996 in.)


INSPECT PISTON OIL CLEARANCE
  1. Measure the cylinder bore diameter in the thrust directions.

  1. Subtract the piston diameter measurement from the cylinder bore diameter measurement.

    Standard oil clearance:
    0.050 to 0.068 mm (0.00197 to 0.00268 in.)

    Maximum oil clearance:
    0.13 mm (0.00512 in.)

    If the oil clearance is more than the maximum, replace all 8 pistons and rebore all 8 cylinders. If necessary, replace the cylinder block.

    HINT:
    When replacing the cylinder block, use a piston with the same number mark as the cylinder diameter marked on the cylinder block.


INSPECT RING GROOVE CLEARANCE

  1. A004880E01
    Inspect the piston ring groove clearance.

    1. Using a feeler gauge, measure the clearance between a new piston ring and the wall of the ring groove.

      Standard Ring Groove Clearance:
      Piston Ring
      Specified Condition
      No. 1
      0.030 to 0.080 mm (0.00118 to 0.00315 in.)
      No. 2
      0.020 to 0.060 mm (0.000787 to 0.00236 in.)

      If the clearance is not as specified, replace the piston.


INSPECT PISTON RING END GAP

  1. A004872E01
    Insert the piston ring into the cylinder bore.

  1. Using a piston, push the piston ring a little beyond the bottom of the ring travel, 105 mm (4.13 in.) from the top of the cylinder block.

  1. A050189E02
    Using a feeler gauge, measure the end gap.

    Standard End Gap:
    Piston Ring
    Specified Condition
    No. 1 piston ring
    0.300 to 0.400 mm (0.0118 to 0.0157 in.)
    No. 2 piston ring
    0.400 to 0.550 mm (0.0157 to 0.0217 in.)
    Oil ring (Side rail)
    0.130 to 0.380 mm (0.00512 to 0.0150 in.)

    Maximum End Gap:
    Piston Ring
    Specified Condition
    No. 1 piston ring
    1.10 mm (0.0433 in.)
    No. 2 piston ring
    1.30 mm (0.0512 in.)
    Oil ring (Side rail)
    0.90 mm (0.0354 in.)

    If the end gap is more than the maximum, replace the piston ring. If the end gap is more than the maximum even with a new piston ring, rebore all 8 cylinders or replace the cylinder block sub-assembly.


INSPECT PISTON PIN OIL CLEARANCE

  1. Check each mark on the piston and connecting rod.

    A175227E01

  1. A175229
    Using a caliper gauge, measure the inside diameter of the piston pin hole.

    Standard Piston Pin Hole Inside Diameter:
    Mark
    Specified Condition
    A
    21.998 to 22.001 mm (0.86606 to 0.86618 in.)
    B
    22.002 to 22.004 mm (0.86622 to 0.86630 in.)
    C
    22.005 to 22.007 mm (0.86634 to 0.86642 in.)

  1. A054725E02
    Using a micrometer, measure the piston pin diameter.

    Standard Piston Pin Diameter:
    Piston Pin
    Specified Condition
    A
    21.997 to 22.000 mm (0.86602 to 0.86614 in.)
    B
    22.001 to 22.003 mm (0.86618 to 0.86626 in.)
    C
    22.004 to 22.006 mm (0.86630 to 0.86638 in.)

  1. Subtract the piston pin diameter measurement from the piston pin hole diameter measurement.

    Standard oil clearance:
    -0.002 to 0.004 mm (-0.0000787 to 0.000157 in.)

    If the oil clearance is more than the maximum, replace the piston and piston pin as a set.

  1. A054726E01
    Using a caliper gauge, measure the inside diameter of the connecting rod bush.

    Standard Bush Inside Diameter:
    Bush
    Specified Condition
    A
    22.005 to 22.008 mm (0.86633 to 0.86646 in.)
    B
    22.009 to 22.011 mm (0.86650 to 0.86657 in.)
    C
    22.012 to 22.014 mm (0.86661 to 0.86669 in.)

    If the bush inside diameter is not as specified, replace the connecting rod small end bush and check the oil clearance.

  1. Subtract the piston pin diameter measurement from the bush inside diameter measurement.

    Standard oil clearance:
    0.005 to 0.011 mm (0.000197 to 0.000433 in.)

    Maximum oil clearance:
    0.05 mm (0.00197 in.)

    If the oil clearance is more than the maximum, replace the connecting rod small end bush. If necessary, replace the piston and piston pin with a new piston and pin set.


INSPECT CONNECTING ROD SUB-ASSEMBLY

  1. A054727E01
    Using a rod aligner and feeler gauge, check the connecting rod alignment.

    1. Check if the connecting rod is bent.

      Maximum bend:
      0.05 mm (0.00197 in.) per 100 mm (3.94 in.)

      If the bend is more than the maximum, replace the connecting rod sub-assembly.

    2. A054728E01
      Check if the connecting rod is twisted.

      Maximum twist:
      0.15 mm (0.00591 in.) per 100 mm (3.94 in.)

      If the twist is more than the maximum, replace the connecting rod sub-assembly.


INSPECT CRANKSHAFT

  1. A005121E01
    Inspect for circle runout.

    1. Place the crankshaft on V-blocks.

    2. Using a dial indicator, measure the circle runout at the center journal.

      Standard circle runout:
      0 to 0.06 mm (0 to 0.00236 in.)

      Maximum circle runout:
      0.08 mm (0.00315 in.)

      If the circle runout is more than the maximum, replace the crankshaft.

  1. A175231
    Inspect the main journals.

    1. Using a micrometer, measure the diameter of each main journal.

      Standard diameter:
      66.988 to 67.000 mm (2.6373 to 2.6378 in.)

      If the diameter is not as specified, check the oil clearance. If necessary, replace the crankshaft.

    2. Check each main journal for taper and out of round as shown in the illustration.

      Maximum taper and out of round:
      0.02 mm (0.000787 in.)

      If the taper and out of round is more than the maximum, replace the crankshaft.

  1. A175230
    Inspect the crank pins.

    1. Using a micrometer, measure the diameter of each crank pin.

      Standard diameter:
      51.982 to 52.000 mm (2.0465 to 2.0472 in.)

      If the diameter is not as specified, check the oil clearance. If necessary, replace the crankshaft.

    2. Check each crank pin for taper and out of round as shown in the illustration.

      Maximum taper and out of round:
      0.02 mm (0.000787 in.)

      If the taper and out of round is more than the maximum, replace the crankshaft.


INSPECT CRANKSHAFT OIL CLEARANCE

  1. A163797E02
    Clean each crankshaft journal and bearing.

    HINT:
    1. Main bearings come in widths of 19.5 mm (0.768 in.) and 22.5 mm (0.886 in.). Install the 22.5 mm (0.886 in.) bearings in the No. 1 and No. 5 cylinder block journal positions with the crankshaft bearing cap. Install the 19.5 mm (0.768 in.) bearings in the other positions.
    2. Upper bearings have an oil groove and oil holes; lower bearings do not.

  1. Check each crankshaft journal and bearing for pitting and scratches.
    If the journal or bearing is damaged, replace the bearings. If necessary, replace the crankshaft.

  1. A004216E01
    Align the bearing claw with the claw groove of the cylinder block, and push in the 5 upper bearings.

  1. A004214E01
    Align the bearing claw with the claw groove of the crankshaft bearing cap, and push in the 5 lower bearings.

    HINT:
    A number is marked on each bearing cap to indicate the installation position.

  1. A066654E01
    Apply engine oil to the thrust washer set.

  1. Install the 2 thrust washers under the No. 3 journal position of the cylinder block with the oil grooves facing outward.

  1. A004217E01
    Install the 2 thrust washers on the No. 3 crankshaft bearing cap with the grooves facing outward.

  1. Place the crankshaft on the cylinder block.

  1. A005097E01
    Lay a strip of Plastigage across each journal.

  1. A005091E01
    Examine the front mark and number, and install the 5 crankshaft bearing caps to the cylinder block.

    HINT:
    A number is marked on each bearing cap to indicate the installation position.

  1. Apply a light coat of engine oil to the threads and under the heads of the crankshaft bearing cap bolts.

  1. Install the 10 crankshaft bearing cap bolts.

    HINT:
    If any one of the main bearing cap bolts is broken or deformed, replace it.


    1. A005095E02
      Uniformly tighten the 10 crankshaft bearing cap bolts in several passes in the sequence shown in the illustration.

      Torque:
      27 N*m{ 275 kgf*cm , 20 ft.*lbf }

      NOTICE:
      Do not turn the crankshaft.

      If any of the bearing cap bolts cannot meet the torque specification, replace the bearing cap bolt.

    2. A101478E11
      Mark the front of the crankshaft bearing cap bolts with paint.

    3. Tighten the crankshaft bearing cap bolts 90° as shown in the illustration.

    4. Check that the painted marks are now at a 90° angle to the front.

  1. A005095E01
    Uniformly loosen and remove the 10 crankshaft bearing cap bolts in the sequence shown in the illustration.

  1. A005093E01
    Using 2 screwdrivers, gradually pry up and remove the 5 crankshaft bearing caps, 5 lower bearings and 2 lower thrust washers (No. 3 crankshaft bearing cap only).

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and bearing cap.

    HINT:
    1. Keep the lower bearing and crankshaft bearing cap together.
    2. Arrange the removed parts in the correct order.

  1. A005098E03
    Measure the Plastigage at its widest point.

    Standard Oil Clearance:
    Number Mark
    Specified Condition
    No. 1 and No. 5
    0.028 to 0.046 mm (0.00110 to 0.00181 in.)
    Other
    0.040 to 0.058 mm (0.00157 to 0.00228 in.)

    Maximum oil clearance:
    0.065 mm (0.00256 in.)

    If the oil clearance is more than the maximum, replace the bearings. If necessary, replace the crankshaft.

    HINT:
    A005176E02
    If replacing a standard bearing, replace it with one that has the same number. If the number of the bearing cannot be determined, select the correct bearing by adding together the numbers imprinted on the cylinder block and crankshaft. Then refer to the table below for the appropriate bearing number. There are 5 sizes of standard bearings. For No. 1 and No. 5 position bearings, use bearings marked 3, 4, 5, 6 and 7. For other position bearings, use bearings marked 1, 2, 3, 4 and 5.

    1. EXAMPLE:
      No. 1 and No. 5 journal
      Cylinder block (A) "7" + Crankshaft (B) "6" = Total number 13 (Use bearing "5")
      Other journal
      Cylinder block (A) "7" + Crankshaft (B) "6" = Total number 13 (Use bearing "3")
    A = Cylinder block number mark
    B = Crankshaft number mark

    HINT:
    (Cylinder block journal diameter - crankshaft journal diameter - 5) X 1000 = A + B

    Bearing Chart:
    (A) + (B)
    No. 1 and No. 5 Journal
    Other Journal
    0 to 6
    3
    1
    6 to 11
    4
    2
    12 to 17
    5
    3
    18 to 23
    6
    4
    24 to 28
    7
    5

    Standard Cylinder Block Crankshaft Journal Bore Diameter (A):
    Number Mark
    Specified Condition
    Mark 00
    72.000 mm (2.83465 in.)
    Mark 01
    72.001 mm (2.83469 in.)
    Mark 02
    72.002 mm (2.83472 in.)
    Mark 03
    72.003 mm (2.83476 in.)
    Mark 04
    72.004 mm (2.83480 in.)
    Mark 05
    72.005 mm (2.83484 in.)
    Mark 06
    72.006 mm (2.83488 in.)
    Mark 07
    72.007 mm (2.83492 in.)
    Mark 08
    72.008 mm (2.83496 in.)
    Mark 09
    72.009 mm (2.83500 in.)
    Mark 10
    72.010 mm (2.83504 in.)
    Mark 11
    72.011 mm (2.83508 in.)
    Mark 12
    72.012 mm (2.83512 in.)
    Mark 13
    72.013 mm (2.83516 in.)
    Mark 14
    72.014 mm (2.83520 in.)
    Mark 15
    72.015 mm (2.83524 in.)
    Mark 16
    72.016 mm (2.83528 in.)

    Standard Crankshaft Journal Diameter (B):
    Number Mark
    Specified Condition
    Mark 00
    67.000 mm (2.63780 in.)
    Mark 01
    66.999 mm (2.63776 in.)
    Mark 02
    66.998 mm (2.63772 in.)
    Mark 03
    66.997 mm (2.63768 in.)
    Mark 04
    66.996 mm (2.63764 in.)
    Mark 05
    66.995 mm (2.63760 in.)
    Mark 06
    66.994 mm (2.63756 in.)
    Mark 07
    66.993 mm (2.63752 in.)
    Mark 08
    66.992 mm (2.63748 in.)
    Mark 09
    66.991 mm (2.63744 in.)
    Mark 10
    66.990 mm (2.63740 in.)
    Mark 11
    66.989 mm (2.63736 in.)
    Mark 12
    66.988 mm (2.63732 in.)

    Standard Bearing Center Wall Thickness:
    Number Mark
    Specified Condition
    Mark 1
    2.481 to less than 2.484 mm (0.0977 to less than 0.0978 in.)
    Mark 2
    2.484 to less than 2.487 mm (0.0978 to less than 0.0979 in.)
    Mark 3
    2.487 to less than 2.490 mm (0.0979 to less than 0.0980 in.)
    Mark 4
    2.490 to less than 2.493 mm (0.0980 to less than 0.0981 in.)
    Mark 5
    2.493 to less than 2.496 mm (0.0981 to less than 0.0983 in.)
    Mark 6
    2.496 to less than 2.499 mm (0.0983 to less than 0.0984 in.)
    Mark 7
    2.499 to less than 2.502 mm (0.0984 to less than 0.0985 in.)

  1. Completely remove the Plastigage.

  1. Perform the inspection above for each journal.


INSPECT CONNECTING ROD BOLT

  1. A109692E01
    Using a vernier caliper, measure the tension portion of the connecting rod bolt.

    Standard diameter:
    7.200 to 7.300 mm (0.283 to 0.287 in.)

    Minimum diameter:
    7.00 mm (0.276 in.)

    If the diameter is less than the minimum, replace the connecting rod bolt.


INSPECT CRANKSHAFT BEARING CAP BOLT

  1. A175232E01
    Using a vernier caliper, measure the thread outside diameter of the main bearing cap bolt.

    Measuring point:
    67.0 mm (2.64 in.)

    Standard diameter:
    10.760 to 10.970 mm (0.424 to 0.432 in.)

    Minimum diameter:
    10.40 mm (0.409 in.)

    If the diameter is less than the minimum, replace the crankshaft bearing cap bolt.


INSPECT NO. 1 OIL NOZZLE SUB-ASSEMBLY

  1. A142819
    Push the check valve with a pin to check if it is stuck.
    If stuck, replace the oil nozzle sub-assembly.

  1. Push the check valve with a pin to check if it moves smoothly.
    If it does not move smoothly, clean or replace the No. 1 oil nozzle sub-assembly.

  1. A150150E02
    While covering A, apply air into B. Check that air does not leak through C. Perform the check again while covering B and applying air into A.
    If air leaks, clean or replace the No. 1 oil nozzle sub-assembly.

  1. A142820E02
    Push the check valve while covering A, and apply air into B. Check that air passes through C. Perform the check again while covering B, pushing the check valve and applying air into A.
    If air does not pass through C, clean or replace the No. 1 oil nozzle sub-assembly.

← DISASSEMBLY (Sep 2011 – Dec 2011)REPLACEMENT (Sep 2011 – Dec 2011) →