2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

A flat type knock sensor (non-resonant type) has a structure that can detect vibrations between approximately 6 kHz and 15 kHz.
Knock sensors are fitted onto the engine block to detect engine knocking.
The knock sensor contains a piezoelectric element which generates a voltage when it becomes deformed.
The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.
DTC Code
DTC Detection Condition
Trouble Area
P0327
The output voltage of the knock sensor (for Bank 1 Sensor 1) is 0.5 V or less (1 trip detection logic).
  1. Short in knock sensor (for Bank 1 Sensor 1) circuit
  1. Knock sensor (for Bank 1 Sensor 1)
  1. ECM
P0328
The output voltage of the knock sensor (for Bank 1 Sensor 1) is 4.5 V or higher (1 trip detection logic).
  1. Open in knock sensor (for Bank 1 Sensor 1) circuit
  1. Knock sensor (for Bank 1 Sensor 1)
  1. ECM
P0332
The output voltage of the knock sensor (for Bank 2 Sensor 1) is 0.5 V or less (1 trip detection logic).
  1. Short in knock sensor (for Bank 2 Sensor1) circuit
  1. Knock sensor (for Bank 2 Sensor 1)
  1. ECM
P0333
The output voltage of the knock sensor (for Bank 2 Sensor 1) is 4.5 V or higher (1 trip detection logic).
  1. Open in knock sensor (for Bank 2 Sensor1) circuit
  1. Knock sensor (for Bank 2 Sensor 1)
  1. ECM
P032C
The output voltage of the knock sensor (for Bank 1 Sensor 2) is 0.5 V or less (1 trip detection logic).
  1. Short in knock sensor (for Bank 1 Sensor 2) circuit
  1. Knock sensor (for Bank 1 Sensor 2)
  1. ECM
P032D
The output voltage of the knock sensor (for Bank 1 Sensor 2) is 4.5 V or higher (1 trip detection logic).
  1. Open in knock sensor (for Bank 1 Sensor 2) circuit
  1. Knock sensor (for Bank 1 Sensor 2)
  1. ECM
P033C
The output voltage of the knock sensor (for Bank 2 Sensor 2) is 0.5 V or less (1 trip detection logic).
  1. Short in knock sensor (for Bank 2 Sensor 2) circuit
  1. Knock sensor (for Bank 2 Sensor 2)
  1. ECM
P033D
The output voltage of the knock sensor (for Bank 2 Sensor 2) is 4.5 V or higher (1 trip detection logic).
  1. Open in knock sensor (for Bank 2 Sensor 2) circuit
  1. Knock sensor (for Bank 2 Sensor 2)
  1. ECM

HINT:
When any of DTCs P0327, P0328, P0332, P0333, P032C, P032D, P033C and P033D is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the engine switch is turned off.

Reference: Inspection using an oscilloscope.
A150243E01

Standard:
Tester Connection
Tool Setting
Condition
Specified Condition
C45-94 (KNK1) - C45-93 (EKNK)
0.01 to 10 V/DIV.
0.01 to 10 msec./DIV.
Keep engine speed at 4000 rpm with warm engine
The correct waveform is as shown
C45-117 (KNK2) - C45-116 (EKN2)
0.01 to 10 V/DIV.
0.01 to 10 msec./DIV.
Keep engine speed at 4000 rpm with warm engine
The correct waveform is as shown
C45-96 (KNK3) - C45-95 (EKN3)
0.01 to 10 V/DIV.
0.01 to 10 msec./DIV.
Keep engine speed at 4000 rpm with warm engine
The correct waveform is as shown
C45-119 (KNK4) - C45-118 (EKN4)
0.01 to 10 V/DIV.
0.01 to 10 msec./DIV.
Keep engine speed at 4000 rpm with warm engine
The correct waveform is as shown


MONITOR DESCRIPTION

The knock sensor, located on the cylinder block, detects spark knock. When spark knock occurs, the piezoelectric element of the sensor vibrates. When the ECM detects a voltage in this frequency range, it retards the ignition timing to suppress the spark knock.
The ECM also senses background engine noise with the knock sensor and uses this noise to check for faults in the sensor. If the knock sensor signal level is too low for more than 10 seconds, or if the knock sensor output voltage is outside the normal range, the ECM interprets this as a fault in the knock sensor and stores DTC(s).

WIRING DIAGRAM

A165784E08

INSPECTION PROCEDURE

HINT:
  1. DTCs P0327 and P0328 are for the bank 1 sensor 1 knock sensor circuit.
  2. DTCs P032C and P032D are for the bank 1 sensor 2 knock sensor circuit.
  3. DTCs P0332 and P0333 are for the bank 2 sensor 1 knock sensor circuit.
  4. DTCs P033C and P033D are for the bank 2 sensor 2 knock sensor circuit.
  5. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  6. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  7. Bank 2 refers to the bank that does not include the No. 1 cylinder.


1. INSPECT KNOCK SENSOR
A187305E05
  1. Disconnect the C45 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C45-94 (KNK1) - C45-93 (EKNK)
    20°C (68°F)
    120 to 280 kΩ
    C45-117 (KNK2) - C45-116 (EKN2)
    20°C (68°F)
    120 to 280 kΩ
    C45-96 (KNK3) - C45-95 (EKN3)
    20°C (68°F)
    120 to 280 kΩ
    C45-119 (KNK4) - C45-118 (EKN4)
    20°C (68°F)
    120 to 280 kΩ

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 3
A


2. CHECK HARNESS AND CONNECTOR (ECM - KNOCK SENSOR)
A187306E02
  1. Disconnect the C45 ECM connector.

  1. Disconnect the U3, U4, U5 or U6 knock sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    U3-2 - C45-94 (KNK1)
    Always
    Below 1 Ω
    U3-1 - C45-93 (EKNK)
    Always
    Below 1 Ω
    U4-2 - C45-117 (KNK2)
    Always
    Below 1 Ω
    U4-1 - C45-116 (EKN2)
    Always
    Below 1 Ω
    U5-2 - C45-96 (KNK3)
    Always
    Below 1 Ω
    U5-1 - C45-95 (EKN3)
    Always
    Below 1 Ω
    U6-2 - C45-119 (KNK4)
    Always
    Below 1 Ω
    U6-1 - C45-118 (EKN4)
    Always
    Below 1 Ω
    U3-2 or C45-94 (KNK1) - Body ground
    Always
    10 kΩ or higher
    U3-1 or C45-93 (EKNK) - Body ground
    Always
    10 kΩ or higher
    U4-2 or C45-117 (KNK2) - Body ground
    Always
    10 kΩ or higher
    U4-1 or C45-116 (EKN2) - Body ground
    Always
    10 kΩ or higher
    U5-2 or C45-96 (KNK3) - Body ground
    Always
    10 kΩ or higher
    U5-1 or C45-95 (EKN3) - Body ground
    Always
    10 kΩ or higher
    U6-2 or C45-119 (KNK4) - Body ground
    Always
    10 kΩ or higher
    U6-1 or C45-118 (EKN4) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE KNOCK SENSOR (Click here)

3. INSPECT ECM

  1. A148715E62
    Disconnect the U3, U4, U5 or U6 knock sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Engine switch on (IG)
    4.5 to 5.5 V



NG
REPLACE ECM (Click here)
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)


← P0300 Random / Multiple Cylinder Misfire Detected (+ 8 more codes) (from Jan 2012)P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor) (+ 7 more codes) (from Jan 2012) →