P0560 System Voltage
Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
The battery supplies electricity to the ECM even when the engine switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.| DTC Code |
DTC Detection Condition |
Trouble Area |
| P0560 |
An open in the ECM back up power source circuit (1 trip detection logic). |
|
- HINT:
- If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM is partly cleared.
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. INSPECT FUSE (EFI MAIN) |
![]() ![]() |
Remove the EFI MAIN fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
EFI MAIN fuse
Always
Below 1 Ω
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (EFI NO. 1 FUSE - ECM, BATTERY) |
![]() ![]() |
Check the harness and the connector between the EFI MAIN fuse and ECM.
Remove the EFI MAIN fuse from the engine room relay block.
Disconnect the A38 ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
EFI MAIN fuse terminal 2 - A38-1 (BATT)
Always
Below 1 Ω
EFI MAIN fuse terminal 2 or A38-1 (BATT) - Body ground
Always
10 kΩ or higher
Check the harness and the connector between the EFI MAIN fuse and battery.
Remove the EFI MAIN fuse from the engine room relay block.
Disconnect the positive battery terminal.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
Battery positive (+) terminal - EFI MAIN fuse terminal 1
Always
Below 1 Ω
Battery positive (+) terminal or EFI MAIN fuse terminal 1- Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 3. INSPECT BATTERY |
Check that the battery is not depleted (Click here).
- OK:
- Battery is not depleted.
|
|
||||
| OK | |
| 4. CHECK BATTERY TERMINAL |
Check that the battery terminals are not loose or corroded.
- OK:
- Battery terminals are not loose or corroded.
|
|
||||
| OK | |
| 5. CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester on.
Clear DTCs (Click here).
Turn the engine switch off and turn the tester off.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
Result Result
Proceed to
P0560 is output
A
No DTC is output
B
|
|
||||
| A | ||
| ||


