2011-2013 Land Cruiser · Service Manual Vehicle Interior

SYSTEM DESCRIPTION

Troubleshooting · Vehicles built from Jan 2012

Versions by build date: from Sep 2011 from Jan 2012


PRE-CRASH SAFETY SYSTEM
  1. The pre-crash safety system optimizes and activates occupant protection equipment in an attempt to reduce injury in a collision.


OUTLINE OF PRE-CRASH SAFETY SYSTEM
Operating Condition
Control
Transmitting ECU
Receiving ECU
Part Operated
Operates according to sensor detection
Pre-crash safety seat belts
Distance control ECU
Seat belt control ECU
Front seat outer belts
Operates according to sensor detection
Pre-crash safety brake assist
Distance control ECU
Master cylinder solenoid (skid control ECU)
Brake assist system
Operates when sudden braking occurs
Pre-crash safety seat belts
Master cylinder solenoid (skid control ECU)
Seat belt control ECU
Front seat outer belts
  1. When operating according to sensor detection:
    The distance control ECU uses information from the millimeter wave radar sensor to determine if the pre-crash safety system should be activated. If so, the distance control ECU sends signals to the master cylinder solenoid (skid control ECU) and seat belt control ECU through CAN communication. In response to these signals, the pre-crash safety system operates as follows:

    1. The seat belt control ECU initiates control of the pre-crash safety seat belts.
    2. The master cylinder solenoid (skid control ECU) activates the pre-crash safety brake assist system.

  2. When operating as a result of sudden braking:
    The master cylinder solenoid (skid control ECU) uses brake pressure information and other data to determine if the driver has suddenly applied the brakes. If so, the master cylinder solenoid (skid control ECU) sends a signal to the seat belt control ECU through CAN communication and the pre-crash safety seat belt activates.


OUTLINE OF PRE-CRASH SAFETY SEAT BELT CONTROL
  1. Pre-crash safety seat belt operation conditions:

    1. The driver firmly depresses the brake pedal suddenly.
    2. The driver oversteers or the vehicle is spinning.

  2. Pre-crash safety seat belt non-operation conditions:
    If any of the following conditions are met, the pre-crash safety seat belt does not operate.

    1. The seat belts are not fastened.
    2. The engine switch is off or on (ACC).
    3. The vehicle speed is approximately 30 km/h (18.6 mph) or less.
    4. When the pre-crash safety seat belts are repeatedly operated and the seat belt control ECU overheats, seat belt operation is prohibited to protect the ECU.

    HINT:
    The PCS warning indicator light in the combination meter will blink at this time.


OUTLINE OF PRE-CRASH SAFETY BRAKE ASSIST SYSTEM
  1. The pre-crash safety brake assist system operates depending on what the sensor detects. The system then enters standby mode before a collision. When the driver depresses the brake pedal, brake fluid pressure is increased to improve fluid pressure response and improve vehicle speed reduction rate.

  2. Operative condition

    1. Refer to the sensor description under "outline of pre-crash safety system" (see above).

    2. When the driver depresses the brake pedal after the distance control ECU determines that a collision is unavoidable:
      Brake fluid pressure is increased at the same time the driver depresses the brake pedal.

    3. When the driver depresses the brake pedal before the distance control ECU determines that a collision is unavoidable:
      Brake fluid pressure is increased at the same time that the distance control ECU receives a pre-crash sensor signal (indicating that other vehicles or objects are in front of the vehicle).


OPERATIVE CONDITION AND INOPERATIVE CONDITION OF EACH CONTROL (REVIEW)

Pre-crash Safety Seat Belts*1
Pre-crash Safety Seat Belts*2
Pre-crash Safety Brake Assist*2
When the engine switch is off or on (ACC).
-
-
-
When a warning message is displayed on the multi-information display.
*3
*3
*3
When the seat belt(s) is/are fastened.
*4
*4
○
Operates when the vehicle speed is 30 km/h (18.6 mph) or more, regardless of relative speed.
○
-
-
Operates when the vehicle speed is 5 km/h (3 mph) or more and relative speed is 30 km/h (18.6 mph).
-
○
-
Operates when the vehicle speed is 30 km/h (18.6 mph) or more and relative speed is 30 km/h (18.6 mph).
-
-
○
When the vehicle collides with an object outside the detection range of the millimeter wave radar sensor (side collision, rear collision, etc.).
*5
-
-
When the millimeter wave radar sensor cannot detect a possible collision object.
*5
-
-

HINT:
  1. *1: Operates when brakes are suddenly applied
  2. *2: Operates according to sensor detection
  3. *3: Inoperative parts are different depending on malfunction areas
  4. *4: Only operates when a seat belt is fastened
  5. *5: Pre-crash safety seat belts may operate when brakes are suddenly applied


PRECAUTION FOR PRE-CRASH SAFETY SYSTEM OPERATION

  1. When the millimeter wave radar sensor detects an object in front of the vehicle under the conditions described below, the distance control ECU may determine that a collision is unavoidable, and activate the pre-crash safety system. However, this is not abnormal.
    H101107E03

    HINT:
    1. The pre-crash safety system will not activate when the pre-crash safety sensor detects safety cones and other plastic objects.
    2. The pre-crash safety system may or may not activate when the pre-crash safety sensor detects the following objects: people, bicycles, motorcycles, trees, animals and snow fences.
      Object Type
      Example
      Objects that cannot be detected.
      Plastic items (safety cones)
      Objects that cannot be detected in a stable manner.
      People, bicycles, motorcycles, trees, animals, snow fences, etc.

← SYSTEM DESCRIPTION (from Sep 2011)HOW TO PROCEED WITH TROUBLESHOOTING (Sep 2011 – Dec 2011) →