2011-2013 Land Cruiser · Service Manual Vehicle Interior

TERMINALS OF ECU

System information · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
B122343E14
  1. Disconnect the E29 and E30 ECU connectors.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E29-1 (+B) - Body ground
    B - Body ground
    +B power supply
    Always
    11 to 14 V
    E29-18 (IG) - Body ground
    B - Body ground
    IG power supply
    Engine switch on (IG)
    11 to 14 V
    Engine switch off
    Below 1 Ω
    E29-17 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the E29 and E30 ECU connectors.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E29-2 (IND) - Body ground
    V - Body ground
    Security indicator signal
    Security indicator illuminates (illuminates only for 60 sec. in alarm sounding state (blinking when system in armed state))
    6 to 11 V
    E30-20 (SH-) - Body ground*1
    LG - Body ground
    Security horn signal
    Security horn not sounding (theft deterrent system in alarm sounding state)
    11 to 14 V
    Security horn sounding (theft deterrent system in alarm sounding state)
    0.5 to 4 V
    E30-24 (HSW) - Body ground
    W - Body ground
    Engine hood courtesy switch signal
    Engine hood closed
    10 kΩ or higher
    Engine hood open
    Below 1 Ω
    E30-7 (SSCL) - Body ground*2
    L - Body ground
    Theft warning siren signal
    Theft warning siren sounding (theft warning system in alarm sounding state)
    Below 2 V
    Theft warning siren not sounding (theft warning system in alarm sounding state)
    4.5 to 14 V
    E30-4 (IOUT) - Body ground*3
    P - Body ground
    Intrusion sensor signal input
    No moving object detected
    9 to 14 V
    Moving object detected during arming preparation state or armed state
    Pulse generation
    E30-5 (SSW1) - Body ground*3
    Y - Body ground
    Intrusion sensor cancel switch signal
    Intrusion sensor cancel switch on
    Below 1.5 V
    Intrusion sensor cancel switch off
    4.5 to 14 V
    E30-21 (CSIF) - Body ground*3
    W - Body ground
    Tilt sensor signal input
    Vehicle tilt not detected
    9 to 14 V
    Vehicle tilt detected during arming preparation state or armed state
    Pulse generation
    E30-23 (GBS) - Body ground*4
    V - Body ground
    Glass breakage sensor signal
    Glass breakage sensor normal
    Below 2 V
    Glass breakage sensor malfunctioning
    4.5 to 14 V

    HINT:
    *1: w/ Security Horn
    *2: w/ Theft Warning Siren
    *3: w/ Intrusion Sensor
    *4: w/ Glass Breakage Sensor


CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)
C172609E03
  1. Disconnect the 2A, 2B, 2D and E3 ECU connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2A-1 (ALTB) - Body ground
    B - Body ground
    Battery power supply
    Always
    11 to 14 V
    2B-20 (BATB) - Body ground
    L - Body ground
    Battery power supply
    Always
    11 to 14 V
    2D-1 (IG) - Body ground
    G - Body ground
    IG power supply
    Engine switch on (IG)
    11 to 14 V
    Engine switch off
    Below 1 V
    2D-8 (ACC) - Body ground
    GR - Body ground
    ACC power supply
    Engine switch on (ACC)
    11 to 14 V
    Engine switch off
    Below 1 V
    2D-62 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    E3-1 (GND3) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the 2A, 2B, 2D and E3 ECU connectors.

  4. Measure the voltage of the connectors.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E1-24 (DCTY) - Body ground
    L - Body ground*1
    Y - Body ground*2
    Driver side door courtesy switch input
    Driver side door open
    Below 1 V
    Engine switch off, and driver side door courtesy switch off
    Pulse generation (see waveform 1 or 2)
    E2-21 (PCTY) - Body ground
    Y - Body ground*1
    L - Body ground*2
    Front passenger side door courtesy switch input
    Front passenger side door open
    Below 1 V
    Engine switch off, and passenger side door courtesy switch off
    Pulse generation (see waveform 3 or 4)
    2C-2 (LCTY) - Body ground
    W - Body ground
    Rear door LH courtesy light switch input
    Rear door LH open
    Below 1 V
    Engine switch off, and rear LH side door courtesy switch off
    Pulse generation (see waveform 5 or 6)
    E2-7 (RCTY) - Body ground
    G - Body ground
    Rear door RH courtesy light switch input
    Rear door RH open
    Below 1 V
    Engine switch off, and rear RH side door courtesy switch off
    Pulse generation (see waveform 7 or 8)
    E2-25 (BCTY) - Body ground
    W - Body ground
    Back door courtesy light switch input
    Back door open
    Below 1 V
    Engine switch off, and back door closed
    Pulse generation (see waveform 9 or 10)
    2D-3 (ACT+) - Body ground
    L - Body ground
    Driver side door lock motor lock drive output
    Master switch (door control switch) or driver side door key cylinder off
    Below 1 V
    Master switch (door control switch) or driver side door key cylinder lock
    11 to 14 V
    E1-5 (ACTD) - Body ground
    B - Body ground
    Driver side door lock motor unlock drive output
    Master switch (door control switch) or driver side door key cylinder off
    Below 1 V
    Master switch (door control switch) or driver side door key cylinder unlock
    11 to 14 V
    2D-3 (ACT+) - Body ground
    L - Body ground
    Front passenger side door lock motor lock drive output
    Master switch (door control switch) or driver side door key cylinder off
    Below 1 V
    Master switch (door control switch) or driver side door key cylinder lock
    11 to 14 V
    2D-2 (ACT-) - Body ground
    B - Body ground
    Front passenger side door lock motor unlock drive output
    Master switch (door control switch) or driver side door key cylinder off
    Below 1 V
    Master switch (door control switch) or driver side door key cylinder unlock
    11 to 14 V
    2D-3 (ACT+) - Body ground
    L - Body ground
    Rear door LH lock motor lock drive output
    Master switch (door control switch) or driver side door key cylinder off
    Below 1 V
    Master switch (door control switch) or driver side door key cylinder lock
    11 to 14 V
    2D-2 (ACT-) - Body ground
    B - Body ground
    Rear door LH lock motor unlock drive output
    Master switch (door control switch) or driver side door key cylinder off
    Below 1 V
    Master switch (door control switch) or driver side door key cylinder unlock
    11 to 14 V
    2D-3 (ACT+) - Body ground
    L - Body ground
    Rear door RH lock motor lock drive output
    Master switch (door control switch) or driver side door key cylinder off
    Below 1 V
    Master switch (door control switch) or driver side door key cylinder lock
    11 to 14 V
    2D-2 (ACT-) - Body ground
    B - Body ground
    Rear door RH lock motor unlock drive output
    Master switch (door control switch) or driver side door key cylinder off
    Below 1 V
    Master switch (door control switch) or driver side door key cylinder unlock
    11 to 14 V
    E1-10 (UL3) - Body ground
    Y - Body ground*1
    L - Body ground*2
    Driver side door lock key switch input
    Driver side door key cylinder unlock
    Below 1 V
    Engine switch off, all doors closed and driver side door key cylinder neutral position
    Pulse generation (see waveform 11 or 12)
    2D-53 (L2) - Body ground
    LG - Body ground
    Driver side door lock key switch input
    Driver side door key cylinder lock
    Below 1 V
    Engine switch off, all doors closed and driver side door key cylinder neutral position
    Pulse generation (see waveform 13 or 14)
    E1-9 (LSWD) - Body ground
    BR - Body ground
    Driver side door lock position switch input
    Driver side door unlock
    Below 1 V
    Engine switch off, all doors closed and driver side door lock
    Pulse generation (see waveform 15 or 16)
    E2-27 (LSWP) - Body ground
    Y - Body ground*1
    BR - Body ground*2
    Passenger side door lock position switch input
    Passenger side door unlock
    Below 1 V
    Engine switch off, all doors closed and passenger side door lock
    Pulse generation (see waveform 17 or 18)
    2C-1 (LSWL) - Body ground
    BR - Body ground
    Rear door LH lock position switch input
    Rear door LH unlock
    Below 1 V
    Engine switch off, all doors closed and rear door LH lock
    Pulse generation (see waveform 19 or 20)
    E2-5 (LSWR) - Body ground
    BR - Body ground
    Rear door RH lock position switch input
    Rear door RH unlock
    Below 1 V
    Engine switch off, all doors closed and rear door RH lock
    Pulse generation (see waveform 21 or 22)
    E1-26 (BDSU) - Body ground
    L - Body ground
    Back door opener switch input
    Back door lock opener switch off
    Below 1 V
    Back door lock opener switch on
    Pulse generation (see waveform 23 or 24)

    HINT:
    1. *1: for LHD
    2. *2: for RHD

    If the result is not as specified, the ECU may have a malfunction.

  5. B122376E01
    Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E1-24 (DCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and driver side door courtesy switch off

  6. B129408E01
    Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E1-24 (DCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and driver side door courtesy switch off

  7. B189909E01
    Using an oscilloscope, check waveform 3.
    Waveform 3 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E2-21 (PCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and passenger side door courtesy switch off

  8. B189910E01
    Using an oscilloscope, check waveform 4.
    Waveform 4 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E2-21 (PCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and passenger side door courtesy switch off

  9. B122376E01
    Using an oscilloscope, check waveform 5.
    Waveform 5 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    2C-2 (LCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and rear LH side door courtesy switch off

  10. B129408E01
    Using an oscilloscope, check waveform 6.
    Waveform 6 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    2C-2 (LCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and rear LH side door courtesy switch off

  11. B122376E01
    Using an oscilloscope, check waveform 7.
    Waveform 7 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E2-7 (RCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and rear RH side door courtesy switch off

  12. B129408E01
    Using an oscilloscope, check waveform 8.
    Waveform 8 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E2-7 (RCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and rear RH side door courtesy switch off

  13. B122376E01
    Using an oscilloscope, check waveform 9.
    Waveform 9 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E2-25 (BCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and back door closed

  14. B129408E01
    Using an oscilloscope, check waveform 10.
    Waveform 10 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E2-25 (BCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and back door closed

  15. B189909E01
    Using an oscilloscope, check waveform 11.
    Waveform 11 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E1-10 (UL3) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and driver side door key cylinder neutral position

  16. B189910E01
    Using an oscilloscope, check waveform 12.
    Waveform 12 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E1-10 (UL3) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and driver side door key cylinder neutral position

  17. B122376E01
    Using an oscilloscope, check waveform 13.
    Waveform 13 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    2D-53 (L2) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and driver side door key cylinder neutral position

  18. B129408E01
    Using an oscilloscope, check waveform 14.
    Waveform 14 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    2D-53 (L2) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and driver side door key cylinder neutral position

  19. B122376E01
    Using an oscilloscope, check waveform 15.
    Waveform 15 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E1-9 (LSWD) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and driver side door lock

  20. B129408E01
    Using an oscilloscope, check waveform 16.
    Waveform 16 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E1-9 (LSWD) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and driver side door lock

  21. B122376E01
    Using an oscilloscope, check waveform 17.
    Waveform 17 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E2-27 (LSWP) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and passenger side door lock

  22. B129408E01
    Using an oscilloscope, check waveform 18.
    Waveform 18 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E2-27 (LSWP) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and passenger side door lock

  23. B189909E01
    Using an oscilloscope, check waveform 19.
    Waveform 19 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    2C-1 (LSWL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and rear door LH lock

  24. B189910E01
    Using an oscilloscope, check waveform 20.
    Waveform 20 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    2C-1 (LSWL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and rear door LH lock

  25. B122376E01
    Using an oscilloscope, check waveform 21.
    Waveform 21 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E2-5 (LSWR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and rear door RH lock

  26. B129408E01
    Using an oscilloscope, check waveform 22.
    Waveform 22 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E2-5 (LSWR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and rear door RH lock

  27. B189909E01
    Using an oscilloscope, check waveform 23.
    Waveform 23 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E1-26 (BDSU) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and back door opener switch on

  28. B189910E01
    Using an oscilloscope, check waveform 24.
    Waveform 24 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E1-26 (BDSU) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and back door opener switch on

← TERMINALS OF ECU (Sep 2011 – Dec 2011)DTC CHECK / CLEAR (from Sep 2011) →