2011-2013 Land Cruiser · Service Manual Drivetrain

DATA LIST / ACTIVE TEST

System information · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


READ DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the engine switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the engine switch on (IG).

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the tester, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    SPD (SP2)
    Output shaft speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    Vehicle stopped: 0 km/h (0 mph) (output shaft speed equal to vehicle speed)
    -
    SPD (NT)
    Input shaft speed/
    Min.: 0 rpm
    Max.: 12750 rpm
    Lock-up:
    1. ON (after warming up engine): Input turbine speed (NT) equal to engine speed
    2. OFF (idling with shift lever in N): Input turbine speed (NT) nearly equal to engine speed
    The data is displayed in increments of 50 rpm.
    Neutral Position SW Signal
    PNP switch status/
    ON or OFF
    Shift lever:
    1. In P or N: ON
    2. Not in P or N: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Stop Light Switch
    Stop light switch status/
    ON or OFF
    Brake pedal:
    1. Depressed: ON
    2. Released: OFF
    -
    Shift Status
    ECM gear shift command/
    1st, 2nd, 3rd, 4th or 5th
    Shift lever:
    1. In D: 1st, 2nd, 3rd, 4th or 5th
    2. In S: 1st, 2nd, 3rd, 4th or 5th
    -
    Shift SW Status (R Range)
    PNP switch status/
    ON or OFF
    Shift lever:
    1. In R: ON
    2. Not in R: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Shift SW Status (P Range)
    PNP switch status/
    ON or OFF
    Shift lever:
    1. In P: ON
    2. Not in P: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Shift SW Status (N Range)
    PNP switch status/
    ON or OFF
    Shift lever:
    1. In N: ON
    2. Not in N: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Shift SW Status (D Range)
    PNP switch status/
    ON or OFF
    Shift lever:
    1. In D: ON
    2. Not in D: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Sports Shift Up SW
    Sport shift up switch status/
    ON or OFF
    1. ON: Shift lever held in "+" (up-shift)
    2. OFF: Shift lever not in "+" (up-shift)
    -
    Sports Shift Down SW
    Sport shift down switch status/
    ON or OFF
    1. ON: Shift lever held in "-" (down-shift)
    2. OFF: Shift lever not in "-" (down-shift)
    -
    Sports Mode Selection SW
    Sport mode select switch status/
    ON or OFF
    Shift lever:
    1. ON: In S, "+" or "-"
    2. OFF: Not in S, "+" or "-"
    -
    Pattern Switch (PWR/M)
    Pattern switch (PWR) status/
    ON or OFF
    Pattern switch (PWR):
    1. Pushed: ON
    2. Not pushed: OFF
    -
    Snow Switch Status
    Pattern switch (2ND) status/
    ON or OFF
    Pattern switch (2ND):
    Pushed: ON
    ↓
    Pattern switch (2ND):
    Pushed: OFF
    -
    A/T Oil Temperature 1
    No. 1 ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall test: Approximately 80°C (176°F)
    2. With engine cold: Equal to ambient temperature
    If the value is -40°C (-40°F) or 215°C (419°F), the No. 1 ATF temperature sensor circuit is open or shorted.
    A/T Oil Temperature 2
    No. 2 ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall test: Approximately 80°C (176°F)
    2. With engine cold: Equal to ambient temperature
    If the value is -40°C (-40°F) or 215°C (419°F), the No. 2 ATF temperature sensor circuit is open or shorted.
    AT Fluid
    Flex lock-up judder judgment/
    ON or OFF
    1. ON: Judder judgment occurs
    2. OFF: Judder judgment does not occur
    -
    Lock Up
    Lock-up/
    ON or OFF
    Lock-up:
    1. Operating: ON
    2. Not operating: OFF
    -
    Lock Up Solenoid Status
    Lock-up solenoid status/
    ON or OFF
    Lock-up solenoid:
    1. Operating: ON
    2. Not operating: OFF
    -
    SLU Solenoid Status
    Shift solenoid valve SLU status/
    ON or OFF
    Shift solenoid valve SLU:
    1. Operating: ON
    2. Not operating: OFF
    -
    SLT Solenoid Status
    Shift solenoid valve SLT status/
    ON or OFF
    1. Accelerator pedal depressed: OFF
    2. Accelerator pedal released: ON
    -


PERFORM ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the engine switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the engine switch on (IG).

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. According to the display on the tester, perform the Active Test.

    Engine and ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the Solenoid (SLU)
    Operate shift solenoid valve SLU
    ON or OFF
    [Vehicle Condition]
    1. The engine is stopped.
    2. The shift lever is in P or N.
    Activate the Solenoid (SLT)*
    Operate shift solenoid valve SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands shift solenoid valve SLT to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. The vehicle is stopped.
    2. The engine is idling.
    Activate the Solenoid (S1)
    Operate shift solenoid valve S1
    ON or OFF
    [Vehicle Condition]
    1. The engine is stopped.
    2. The shift lever is in P or N.
    Activate the Solenoid (S2)
    Operate shift solenoid valve S2
    ON or OFF
    [Vehicle Condition]
    1. The engine is stopped.
    2. The shift lever is in P or N.
    Activate the Lock Up
    Control shift solenoid valve SLU to set automatic transmission to lock-up condition
    ON or OFF
    It is possible to check the shift solenoid valve SLU operation.
    [Vehicle Condition]
    1. The throttle valve opening angle is less than 35%.
    2. The vehicle speed is 60 km/h (37 mph) or more.
    Control the Shift Position
    Operate shift solenoid valve and set each shift position
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    It is possible to check the operation of the shift solenoid valves.
    [Vehicle Condition]
    The vehicle speed is 50 km/h (31 mph) or less.
    Activate the Solenoid (SR)
    Operate shift solenoid valve SR
    ON or OFF
    [Vehicle Condition]
    1. The engine is stopped.
    2. The shift lever is in P or N.
    Activate the Solenoid (SL1)
    Operate shift solenoid valve SL1
    ON or OFF
    [Vehicle Condition]
    1. The engine is stopped.
    2. The shift lever is in P or N.
    Activate the Solenoid (SL2)
    Operate shift solenoid valve SL2
    ON or OFF
    [Vehicle Condition]
    1. The engine is stopped.
    2. The shift lever is in P or N.

    HINT:
    *: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Note that the pressure values in the Active Test and hydraulic test are different.

← FAIL-SAFE CHART (from Sep 2011)DATA LIST / ACTIVE TEST (from Jan 2012) →