DATA LIST / ACTIVE TEST
System information · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| READ DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / Data List.
According to the display on the tester, read the Data List.
ECT Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Calculate Load
Calculated load/
Min.: 0%
Max.: 100%
- Idling: 15.4 to 20.4%
- Running without load (2500 rpm): 20.1 to 25.9%
- Driving with the accelerator fully open at 3000 rpm: 80.3 to 99.6%
- Driving with the accelerator fully open at 4000 rpm: 96.4 to 98%
-
Engine Speed
Engine speed/
Min.: 0 rpm
Max.: 16383.75 rpm
Idling: 550 to 650 rpm
-
Vehicle Speed
Vehicle speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed
The speed is indicated on the speedometer.
Coolant Temp
Engine coolant temperature/
Min.: -40°C (-40°F)
Max.: 140°C (284°F)
After warming up engine: 75 to 90°C (167 to 194°F)
If the value is -40°C (-40°F), the sensor circuit is open.
If the value is 140°C (284°F), the sensor circuit is shorted.
SPD (SP2)
Output shaft speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph) (output shaft speed equal to vehicle speed)
-
SPD (NT)
Input shaft speed/
Min.: 0 rpm
Max.: 12750 rpm
Lock-up: - ON (after warming up engine): Input turbine speed (NT) equal to engine speed
- OFF (idling with shift lever in N): Input turbine speed (NT) nearly equal to engine speed
The data is displayed in increments of 50 rpm.
Neutral Position SW Signal
PNP switch status/
ON or OFF
Shift lever: - In P or N: ON
- Not in P or N: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Stop Light Switch
Stop light switch status/
ON or OFF
Brake pedal: - Depressed: ON
- Released: OFF
-
Shift Status
ECM gear shift command/
1st, 2nd, 3rd, 4th, 5th or 6th
Shift lever: - In D: 1st, 2nd, 3rd, 4th, 5th or 6th
- In S: 1st, 2nd, 3rd, 4th, 5th or 6th
-
Shift SW Status (R Range)
PNP switch status/
ON or OFF
Shift lever: - In R: ON
- Not in R: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Shift SW Status (P Range)
PNP switch status/
ON or OFF
Shift lever: - In P: ON
- Not in P: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Shift SW Status (N Range)
PNP switch status/
ON or OFF
Shift lever: - In N: ON
- Not in N: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Shift SW Status (D Range)
PNP switch status/
ON or OFF
Shift lever: - In D: ON
- Not in D: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Sports Shift Up SW
Sport shift up switch status/
ON or OFF
- ON: Shift lever held in "+" (up-shift)
- OFF: Shift lever not in "+" (up-shift)
-
Sports Shift Down SW
Sport shift down switch status/
ON or OFF
- ON: Shift lever held in "-" (down-shift)
- OFF: Shift lever not in "-" (down-shift)
-
Pattern Switch (PWR/M)
Pattern switch (PWR) status/
ON or OFF
Pattern switch (PWR): - Pushed: ON
- Not pushed: OFF
-
Snow Switch Status
Pattern switch (2ND) status/
ON or OFF
Pattern switch (2ND):
Pushed: ON
↓
Pattern switch (2ND):
Pushed: OFF
-
A/T Oil Temperature 1
No. 1 ATF temperature sensor value/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
- After stall test: Approximately 80°C (176°F)
- With engine cold: Equal to ambient temperature
If the value is -40°C (-40°F) or 215°C (419°F), the No. 1 ATF temperature sensor circuit is open or shorted.
A/T Oil Temperature 2
No. 2 ATF temperature sensor value/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
- After stall test: Approximately 80°C (176°F)
- With engine cold: Equal to ambient temperature
If the value is -40°C (-40°F) or 215°C (419°F), the No. 2 ATF temperature sensor circuit is open or shorted.
Lock Up
Lock-up/
ON or OFF
Lock-up: - Operating: ON
- Not operating: OFF
-
Lock Up Solenoid Status
Lock-up solenoid status/
ON or OFF
Lock-up solenoid: - Operating: ON
- Not operating: OFF
-
SLU Solenoid Status
Shift solenoid valve SLU status/
ON or OFF
Shift solenoid valve SLU: - Operating: ON
- Not operating: OFF
-
SLT Solenoid Status
Shift solenoid valve SLT status/
ON or OFF
- Accelerator pedal depressed: OFF
- Accelerator pedal released: ON
-
Injection Volume from EFI
Injection volume/
Min.: 0 mm3/st
Max.: 639.98 mm3/st
Idling: 3.0 to 10 mm3/st
The injector volume received from the ECM.
Engine Speed from EFI
Engine speed/
Min.: 0 rpm
Max.: 16383.75 rpm
Idling: 550 to 650 rpm
The engine speed received from the ECM.
Intake-Air Temp from EFI
Intake air temperature/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
Equivalent to temperature at intake manifold
The intake air temperature received from the ECM.
Coolant Temp from EFI
Engine coolant temperature/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
After warming up engine: 75 to 90°C (167 to 194°F)
The coolant temperature received from the ECM.
Accel Position from EFI
Accelerator sensor positioning/
Min.: 0%
Max.: 100%
Idling: 0 to 10%
The accelerator position received from the ECM.
# Codes
# of Codes/
Min.: 0
Max.: 255
-
The number of stored DTCs.
MIL ON Run Distance
MIL on run distance/
Min.: 0 km (0 mile)
Max.: 65535 km (40723 mile)
Distance after DTC stored
-
Running Time from MIL ON
Running time from MIL on/
Min.: 0 minutes
Max.: 65535 minutes
Running time after MIL turns on
-
Engine Run Time
Engine run time/
Min.: 0 seconds
Max.: 65535 seconds
Time after the ignition switch turned ON
-
- Idling: 15.4 to 20.4%
| PERFORM ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / Active Test.
According to the display on the tester, perform the Active Test.
ECT Tester Display
Test Part
Control Range
Diagnostic Note
Connect the TC and TE1
Turn on and off TC and TE1 connection
ON or OFF
- ON: TC and TE1 are connected.
- OFF: TC and TE1 are disconnected.
Activate the Solenoid (SLU)
Operate shift solenoid valve SLU
ON or OFF
[Vehicle Condition] - The engine is stopped.
- The shift lever is in P or N.
Activate the Solenoid (SLT)*
Operate shift solenoid valve SLT and raise line pressure
ON or OFF - HINT:
- OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands shift solenoid valve SLT solenoid to turn OFF)
- ON: No action (normal operation)
- OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands shift solenoid valve SLT solenoid to turn OFF)
[Vehicle Condition] - The vehicle is stopped.
- The engine is idling.
Activate the Solenoid (S1)
Operate shift solenoid valve S1
ON or OFF
[Vehicle Condition] - The engine is stopped.
- The shift lever is in P or N.
Activate the Solenoid (S2)
Operate shift solenoid valve S2
ON or OFF
[Vehicle Condition] - The engine is stopped.
- The shift lever is in P or N.
Activate the Solenoid (S3)
Operate shift solenoid valve S3
ON or OFF
[Vehicle Condition] - The engine is stopped.
- The shift lever is in P or N.
Activate the Solenoid (S4)
Operate shift solenoid valve S4
ON or OFF
[Vehicle Condition] - The engine is stopped.
- The shift lever is in P or N.
Activate the Lock Up
Control shift solenoid valve SLU to set automatic transmission to lock-up condition
ON or OFF
It is possible to check the shift solenoid valve SLU operation.
[Vehicle Condition]- The throttle valve opening angle is less than 35%.
- The vehicle speed is 60 km/h (37 mph) or more.
Control the Shift Position
Operate shift solenoid valve and set each shift position
- Press "→" button: Shift up
- Press "←" button: Shift down
It is possible to check the operation of the shift solenoid valves.
[Vehicle Condition]
The vehicle speed is 50 km/h (31 mph) or less.
Activate the Solenoid (SR)
Operate shift solenoid valve SR
ON or OFF
[Vehicle Condition] - The engine is stopped.
- The shift lever is in P or N.
Activate the Solenoid (SL1)
Operate shift solenoid valve SL1
ON or OFF
[Vehicle Condition] - The engine is stopped.
- The shift lever is in P or N.
Activate the Solenoid (SL2)
Operate shift solenoid valve SL2
ON or OFF
[Vehicle Condition] - The engine is stopped.
- The shift lever is in P or N.
- HINT:
- *: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Note that the pressure values in the Active Test and hydraulic test are different.
- ON: TC and TE1 are connected.