DATA LIST / ACTIVE TEST
System information · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| READ DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the intelligent tester, read the Data List.
Engine and ECT Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Neutral Position SW Signal
PNP switch status/
ON or OFF
Shift lever is: - In P or N: ON
- Not in P or N: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Stop Light Switch
Stop light switch status/
ON or OFF
Brake pedal is: - Depressed: ON
- Released: OFF
-
SPD (NT)
Input shaft speed/
Min.: 0 rpm
Max.: 12750 rpm
Lock-up is: - ON (after warming up engine): Input turbine speed (NT) equal to engine speed
- OFF (idling with shift lever in N): Input turbine speed (NT) nearly equal to engine speed
Data is displayed in increments of 50 rpm.
SPD (SP2)
Output shaft speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed)
-
Shift SW Status (P Range)
PNP switch status/
ON or OFF
Shift lever is: - In P: ON
- Not in P: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Pattern Switch (PWR/M)
Pattern switch (PWR) status/
ON or OFF
- ON: Pattern switch (PWR) is pushed
- OFF: Pattern switch (PWR) is not pushed
-
Shift SW Status (R Range)
PNP switch status/
ON or OFF
Shift lever is: - In R: ON
- Not in R: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Shift SW Status (N Range)
PNP switch status/
ON or OFF
Shift lever is: - In N: ON
- Not in N: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Sports Shift Up SW
Sport shift up switch status/
ON or OFF
- ON: Continuously shift to "+" (up-shift)
- OFF: Release "+" (up-shift)
-
Sports Shift Down SW
Sport shift down switch status/
ON or OFF
- ON: Continuously shift to "-" (down-shift)
- OFF: Release "-" (down-shift)
-
Sports Mode Selection SW
Sport mode select switch status/
ON or OFF
Shift lever is: - ON: In S, "+" and "-"
- OFF: Not in S, "+" and "-"
-
Shift SW Status (D Range)
PNP switch status/
ON or OFF
Shift lever is: - In D, S, "+" and "-": ON
- Not in D, S, "+" and "-": OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
A/T Oil Temperature 1
No. 1 ATF temperature sensor value/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
- After stall test: Approximately 80°C (176°F)
- Equal to ambient temperature while engine is cold
If the value is -40°C (-40°F) or 215°C (419°F), the No. 1 ATF temperature sensor circuit is open or shorted.
A/T Oil Temperature 2
No. 2 ATF temperature sensor value/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
- After stall test: Approximately 80°C (176°F)
- Equal to ambient temperature while engine is cold
If the value is -40°C (-40°F) or 215°C (419°F), the No. 2 ATF temperature sensor circuit is open or shorted.
Lock Up
Lock-up/
ON or OFF
Lock-up is: - Operating: ON
- Not operating: OFF
-
Lock Up Solenoid Status
Lock-up solenoid status/
ON or OFF
Lock-up solenoid is: - Operating: ON
- Not operating: OFF
-
Shift Status
ECM gear shift command/
1st, 2nd, 3rd, 4th, 5th or 6th
- In D: 1st, 2nd, 3rd, 4th, 5th or 6th
- In S: 1st, 2nd, 3rd, 4th, 5th or 6th
-
SLT Solenoid Status
Shift solenoid SLT status/
ON or OFF
- Accelerator pedal is depressed: OFF
- Accelerator pedal is released: ON
-
SLU Solenoid Status
Shift solenoid SLU status/
ON or OFF
Shift solenoid SLU is: - Operating: ON
- Not operating: OFF
-
Snow or 2nd Start mode
Pattern switch (2nd) status/
ON or OFF
Pattern switch (2nd):
Pushed: ON
↓
Pattern switch (2nd):
Pushed: OFF
-
AT Fluid
Flex lock-up judder judgment/
ON or OFF
- ON: Judder judgment occurs
- OFF: Judder judgment does not occur
-
- In P or N: ON
| PERFORM ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the intelligent tester, perform the Active Test.
Engine and ECT Tester Display
Test Part
Control Range
Diagnostic Note
Activate the Solenoid (SLU)
Operate the shift solenoid SLU
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever in P or N
Activate the Solenoid (SLT)*
Operate the shift solenoid SLT and raise line pressure
ON or OFF - HINT:
- OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
- ON: No action (normal operation)
- OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
[Vehicle Condition] - Vehicle stopped
- Engine idling
- Shift lever in P or N
Activate the Solenoid (S1)
Operate the shift solenoid S1
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever in P or N
Activate the Solenoid (S2)
Operate the shift solenoid S2
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever in P or N
Activate the Solenoid (S3)
Operate the shift solenoid S3
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever in P or N
Activate the Solenoid (S4)
Operate the shift solenoid S4
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever in P or N
Activate the Lock Up
Control shift solenoid SLU to set automatic transmission to lock-up
ON or OFF
Possible to check shift solenoid valve SLU operation.
[Vehicle Condition]- Throttle valve opening angle: Less than 35%
- Vehicle speed: 60 km/h (36 mph) or more
Control the Shift Position
Operate shift solenoid valves and set each shift position by yourself
- Press "→" button: Shift up
- Press "←" button: Shift down
Possible to check operation of the shift solenoid valves.
[Vehicle Condition]
50 km/h (30 mph) or less
Activate the Solenoid (SR)
Operate the shift solenoid SR
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever in P or N
Activate the Solenoid (SL1)
Operate the shift solenoid SL1
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever in P or N
Activate the Solenoid (SL2)
Operate the shift solenoid SL2
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever in P or N
- HINT:
- *: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Please note that the pressure values in the Active Test and Hydraulic Test are different.
- Engine stopped