DATA LIST / ACTIVE TEST
System information · Vehicles built from Jan 2012
| READ DATA LIST |
- HINT:
- Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the GTS, read the Data List.
Engine and ECT Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
N Range Status
Shift lever N status/
ON or OFF
- ON: Shift lever in N
- OFF: Shift lever not in N
-
Neutral Position SW Signal
PNP switch status/
ON or OFF
Shift lever: - In P or N: ON
- Not in P or N: OFF
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Transfer L4
Transfer status/
ON or OFF
- ON: Transfer position is in L4
- OFF: Transfer position is not L4
-
Stop Light Switch
Stop light switch status/
ON or OFF
Brake pedal: - Depressed: ON
- Released: OFF
-
SPD (NT)
Input shaft speed/
Min.: 0 rpm
Max.: 12750 rpm
Lock-up: - ON (after warming up engine): Input turbine speed (NT) equal to engine speed
- OFF (idling with shift lever in N): Input turbine speed (NT) nearly equal to engine speed
The data is displayed in increments of 50 rpm.
SPD (SP2)
Output shaft speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph) (output shaft speed equal to vehicle speed)
-
Shift SW Status (P Range)
PNP switch status/
ON or OFF
Shift lever: - In P: ON
- Not in P: OFF
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Pattern Switch (PWR/M)
Pattern switch (PWR) status/
ON or OFF
Pattern switch (PWR): - Pushed: ON
- Not pushed: OFF
-
Shift SW Status (R Range)
PNP switch status/
ON or OFF
Shift lever: - In R: ON
- Not in R: OFF
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Shift SW Status (N Range)
PNP switch status/
ON or OFF
Shift lever: - In N: ON
- Not in N: OFF
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Shift SW Status (N, P Range) Supported
Status of PNP switch (N or P) supported/
Supp or Unsupp
-
-
Shift SW Status (N, P Range)
PNP switch status/
ON or OFF
- ON: Shift lever not in P or N
- OFF: Shift lever in P or N
-
Sports Shift Up SW
Sport shift up switch status/
ON or OFF
- ON: Shift lever held in "+" (up-shift)
- OFF: Shift lever not in "+" (up-shift)
-
Sports Shift Down SW
Sport shift down switch status/
ON or OFF
- ON: Shift lever held in "-" (down-shift)
- OFF: Shift lever not in "-" (down-shift)
-
Sports Mode Selection SW
Sport mode select switch status/
ON or OFF
Shift lever: - ON: In S, "+" or "-"
- OFF: Not in S, "+" or "-"
-
Shift SW Status (D Range)
PNP switch status/
ON or OFF
Shift lever: - In D: ON
- Not in D: OFF
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
A/T Oil Temperature 1
No. 1 ATF temperature sensor value/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
- After stall test: Approximately 80°C (176°F)
- With engine cold: Equal to ambient temperature
If the value is -40°C (-40°F) or 215°C (419°F), the No. 1 ATF temperature sensor circuit is open or shorted.
A/T Oil Temperature 2
No. 2 ATF temperature sensor value/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
- After stall test: Approximately 80°C (176°F)
- With engine cold: Equal to ambient temperature
If the value is -40°C (-40°F) or 215°C (419°F), the No. 2 ATF temperature sensor circuit is open or shorted.
Lock Up
Lock-up/
ON or OFF
Lock-up: - Operating: ON
- Not operating: OFF
-
Shift Status
ECM gear shift command/
1st, 2nd, 3rd, 4th, 5th or 6th
Shift lever: - In D: 1st, 2nd, 3rd, 4th, 5th or 6th
- In S: 1st, 2nd, 3rd, 4th, 5th or 6th
-
SLU Solenoid Status
Shift solenoid valve SLU status/
ON or OFF
Shift solenoid valve SLU: - Operating: ON
- Not operating: OFF
-
SLT Solenoid Status
Shift solenoid valve SLT status/
ON or OFF
- Accelerator pedal depressed: OFF
- Accelerator pedal released: ON
-
Snow or 2nd Start Mode
2nd Start mode status/
ON or OFF
- ON: 2nd Start mode on
- OFF: 2nd Start mode off
-
- ON: Shift lever in N
| PERFORM ACTIVE TEST |
- HINT:
- Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the GTS, perform the Active Test.
Engine and ECT Tester Display
Test Part
Control Range
Diagnostic Note
Connect the TC and TE1
Turn on and off TC and TE1 connection
ON or OFF
- ON: TC and TE1 are connected.
- OFF: TC and TE1 are disconnected.
Activate the Solenoid (SLU)
Operate shift solenoid valve SLU
ON or OFF
[Vehicle Condition] - The engine is stopped.
- The shift lever is in P or N.
Activate the Solenoid (SLT)*
Operate shift solenoid valve SLT and raise line pressure
ON or OFF - HINT:
- OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands shift solenoid valve SLT solenoid to turn OFF)
- ON: No action (normal operation)
- OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands shift solenoid valve SLT solenoid to turn OFF)
[Vehicle Condition] - The vehicle is stopped.
- The engine is idling.
Activate the Solenoid (S1)
Operate shift solenoid valve S1
ON or OFF
[Vehicle Condition] - The engine is stopped.
- The shift lever is in P or N.
Activate the Solenoid (S2)
Operate shift solenoid valve S2
ON or OFF
[Vehicle Condition] - The engine is stopped.
- The shift lever is in P or N.
Activate the Solenoid (S3)
Operate shift solenoid valve S3
ON or OFF
[Vehicle Condition] - The engine is stopped.
- The shift lever is in P or N.
Activate the Solenoid (S4)
Operate shift solenoid valve S4
ON or OFF
[Vehicle Condition] - The engine is stopped.
- The shift lever is in P or N.
Activate the Lock Up
Control shift solenoid valve SLU to set automatic transmission to lock-up condition
ON or OFF
It is possible to check the shift solenoid valve SLU operation.
[Vehicle Condition]- The throttle valve opening angle is less than 35%.
- The vehicle speed is 60 km/h (37 mph) or more.
Control the Shift Position
Operate shift solenoid valve and set each shift position
- Press "→" button: Shift up
- Press "←" button: Shift down
It is possible to check the operation of the shift solenoid valves.
[Vehicle Condition]
The vehicle speed is 50 km/h (31 mph) or less.
Activate the Solenoid (SR)
Operate shift solenoid valve SR
ON or OFF
[Vehicle Condition] - The engine is stopped.
- The shift lever is in P or N.
Activate the Solenoid (SL1)
Operate shift solenoid valve SL1
ON or OFF
[Vehicle Condition] - The engine is stopped.
- The shift lever is in P or N.
Activate the Solenoid (SL2)
Operate shift solenoid valve SL2
ON or OFF
[Vehicle Condition] - The engine is stopped.
- The shift lever is in P or N.
- HINT:
- *: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Note that the pressure values in the Active Test and hydraulic test are different.
- ON: TC and TE1 are connected.