P0894 Transmission Component Slipping
Diagnostic trouble codes · Vehicles built from Jan 2012
Also covers:
- P2714 Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT)
DESCRIPTION


Shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and vehicle speed sensor. The ECM adjusts the current to shift solenoid valve SLT to control the hydraulic line pressure coming from the primary regulator valve.
Appropriate line pressure assures smooth shifting with varying engine outputs.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| P0894 |
The ECM detects a malfunction in shift solenoid valve SLT, S1, S2, S3, S4 or SL2, or the 1-2 shift valve, or an incorrect gear 6 ratio according to the difference in speed of the turbine and output shaft, and also by the oil pressure (2 trip detection logic). |
|
| P2714 |
The ECM detects a malfunction in shift solenoid valve SLT (ON side) according to the difference in speed of the turbine and output shaft, and also by the oil pressure (2 trip detection logic*1, 1 trip detection logic*2). |
|
- *1: w/ OBD
- *2: w/o OBD
MONITOR DESCRIPTION
The ECM calculates the amount of heat absorbed by the friction material based on the difference in speed (clutch slippage) between the turbine and output shaft. The ECM illuminates the MIL and stores this DTC when the amount of heat absorption exceeds the specified value.There are two causes of speed difference.
- When the shift solenoid valve SLT remains ON, oil pressure decreases, which causes the clutch engagement force to decrease.
- When a shift solenoid valve remains ON or OFF, the gear position commanded by the ECM and the actual gear position are not the same.
- NOTICE:
- If you continue driving under these conditions, the clutch will burn out and the vehicle will no longer be drivable.
INSPECTION PROCEDURE
| 1. CHECK DTC OUTPUT (IN ADDITION TO DTCS P0894 AND P2714) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the GTS.
Result Result
Proceed to
- Only P0894 is output
- Only P0894 and P2714 are output
A
P0894, P2714 and other DTCs are output
B
- HINT:
- If any other codes besides P0894 and P2714 are output, perform troubleshooting for those DTCs first.
- Only P0894 is output
|
|
||||
| A | |
| 2. PERFORM ACTIVE TEST USING GTS (SHIFT SOLENOID VALVE SLT) |
- NOTICE:
- Perform the test while the ATF temperature is between 50 and 80°C (122 and 176°F).
- Be careful to prevent the hose of SST from interfering with the exhaust pipe.
- Perform the test with the A/C off.
- Perform the test while the ATF temperature is between 50 and 80°C (122 and 176°F).
- HINT:
- Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Remove the test plug on the transmission case and connect SST.

- SST
- 09992-00095
(09992-00231, 09992-00271)
Connect the GTS to the DLC3.
Start the engine and warm it up.
Measure the line pressure with SST.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the GTS, perform the Active Test.
Measure the line pressure.
Engine and ECT Tester Display
Test Part
Control Range
Diagnostic Note
Activate the Solenoid (SLT)*
Operate the shift solenoid SLT and raise line pressure
ON or OFF - HINT:
- OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
- ON: No action (normal operation)
- OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
[Vehicle Condition] - Vehicle stopped
- Engine idling
- HINT:
- *: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Please note that the pressure values in the Active Test and Hydraulic Test are different.
- OK:
- The line pressure changes as specified when performing the Active Test.
|
|
||||
| OK | |
| 3. PERFORM ACTIVE TEST USING GTS (RUNNING TEST) |
- HINT:
- Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Clear the DTC (Click here).
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the GTS, perform the Active Test.
- HINT:
- While driving, the shift position can be forcibly changed with the GTS.
Engine and ECT Tester Display
Test Part
Control Range
Diagnostic Note
Control the Shift Position
Operate shift solenoid valves and set each shift position
- Press "→" button: Shift up
- Press "←" button: Shift down
Possible to check operation of the shift solenoid valves.
[Vehicle Condition]
50 km/h (30 mph) or less
- HINT:
- This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.
- The 4th to 5th and 5th to 6th up-shifts must be performed with the accelerator pedal released.
- The 6th to 5th and 5th to 4th down-shifts must be performed with the accelerator pedal released.
- Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
- The shift position commanded by the ECM is shown in the Data List display on the GTS.
- This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.
Compare the ECM gear shift command and the actual gear position.
Result ECM Gear Shift Command
1st
2nd
3rd
4th
5th
6th
Proceed to
Actual gear position under malfunction
Shift solenoid S1
Stuck ON*1
2nd
2nd
3rd
4th
5th
6th
A
Stuck OFF
1st
1st
3rd
4th
5th
N*2
Shift solenoid S2
Stuck ON
1st
2nd
2nd
4th
6th
6th
B
Stuck OFF
3rd
3rd
3rd
4th
5th
5th
Shift solenoid S3
Stuck ON
1st
2nd
3rd
3rd
N*2
N*2
C
Stuck OFF
3rd
4th
4th
4th
5th
6th
Shift solenoid S4
Stuck ON*3
1st
2nd
3rd
4th
5th
6th
D
Stuck OFF
1st
2nd
3rd
4th
4th
4th
Actual gear position when normal
1st
2nd
3rd
4th
5th
6th
E
- HINT:
- *1: When shift solenoid S1 is stuck ON, the vehicle cannot drive in reverse.
- *2: Neutral
- *3: When shift solenoid S4 is stuck ON, gear shifting is normal.
- *1: When shift solenoid S1 is stuck ON, the vehicle cannot drive in reverse.
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | |
| 4. INSPECT SHIFT SOLENOID VALVE S1 |
Remove the shift solenoid valve S1.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
Shift solenoid valve S1 connector terminal - Shift solenoid valve S1 body
20°C (68°F)
11 to 15 Ω
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
- OK:
Measurement Condition
Specified Condition
- Battery positive (+) → Shift solenoid valve S1 connector
- Battery negative (-) → Shift solenoid valve S1 body
Valve moves and makes an operating noise
- Battery positive (+) → Shift solenoid valve S1 connector
| *a |
Component without harness connected (Shift Solenoid Valve S1) |
|
|
||||
| OK | |
| 5. INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
- OK:
- There are no foreign objects on each valve.
|
|
||||
| OK | |
| 6. INSPECT TORQUE CONVERTER ASSEMBLY |
Check the torque converter assembly (Click here).
- OK:
- The torque converter assembly operates normally.
|
|
||||
| OK | ||
| ||
| 7. INSPECT SHIFT SOLENOID VALVE S2 |
Remove shift solenoid valve S2.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
Shift solenoid valve S2 connector terminal - Shift solenoid valve S2 body
20°C (68°F)
11 to 15 Ω
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
- OK:
Measurement Condition
Specified Condition
- Battery positive (+) → Shift solenoid valve S2 connector
- Battery negative (-) → Shift solenoid valve S2 body
Valve moves and makes an operating noise
- Battery positive (+) → Shift solenoid valve S2 connector
| *a |
Component without harness connected (Shift Solenoid Valve S2) |
|
|
||||
| OK | |
| 8. INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
- OK:
- There are no foreign objects on each valve.
|
|
||||
| OK | |
| 9. INSPECT TORQUE CONVERTER ASSEMBLY |
Check the torque converter assembly (Click here).
- OK:
- The torque converter assembly operates normally.
|
|
||||
| OK | ||
| ||
| 10. INSPECT SHIFT SOLENOID VALVE S3 |
Remove the shift solenoid valve S3.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
Shift solenoid valve S3 connector terminal - Shift solenoid valve S3 body
20°C (68°F)
11 to 15 Ω
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
- OK:
Measurement Condition
Specified Condition
- Battery positive (+) → Shift solenoid valve S3 connector
- Battery negative (-) → Shift solenoid valve S3 body
Valve moves and makes an operating noise
- Battery positive (+) → Shift solenoid valve S3 connector
| *a |
Component without harness connected (Shift Solenoid Valve S3) |
|
|
||||
| OK | |
| 11. INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
- OK:
- There are no foreign objects on each valve.
|
|
||||
| OK | |
| 12. INSPECT TORQUE CONVERTER ASSEMBLY |
Check the torque converter assembly (Click here).
- OK:
- The torque converter assembly operates normally.
|
|
||||
| OK | ||
| ||
| 13. INSPECT SHIFT SOLENOID VALVE S4 |
Remove the shift solenoid valve S4.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
Shift solenoid valve S4 connector terminal - Shift solenoid valve S4 body
20°C (68°F)
11 to 15 Ω
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
- OK:
Measurement Condition
Specified Condition
- Battery positive (+) → Shift solenoid valve S4 connector
- Battery negative (-) → Shift solenoid valve S4 body
Valve moves and makes an operating noise
- Battery positive (+) → Shift solenoid valve S4 connector
| *a |
Component without harness connected (Shift Solenoid Valve S4) |
|
|
||||
| OK | |
| 14. INSPECT SHIFT SOLENOID VALVE SL2 |
Remove the shift solenoid valve SL2.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
5.0 to 5.6 Ω
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
- OK:
Measurement Condition
Specified Condition
- Battery positive (+) with a 21 W bulb → Terminal 1
- Battery negative (-) → Terminal 2
Valve moves and makes an operating noise
- Battery positive (+) with a 21 W bulb → Terminal 1
| *a |
Component without harness connected (Shift Solenoid Valve SL2) |
|
|
||||
| OK | |
| 15. INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
- OK:
- There are no foreign objects on each valve.
|
|
||||
| OK | |
| 16. INSPECT TORQUE CONVERTER ASSEMBLY |
Check the torque converter assembly (Click here).
- OK:
- The torque converter assembly operates normally.
|
|
||||
| OK | ||
| ||
| 17. INSPECT SHIFT SOLENOID VALVE SLT |
Remove shift solenoid valve SLT.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
5.0 to 5.6 Ω
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
- OK:
Measurement Condition
Specified Condition
- Battery positive (+) with a 21 W bulb → Terminal 2
- Battery negative (-) → Terminal 1
Valve moves and makes an operating noise
- Battery positive (+) with a 21 W bulb → Terminal 2
| *a |
Component without harness connected (Shift Solenoid Valve SLT) |
|
|
||||
| OK | |
| 18. INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
- OK:
- There are no foreign objects on each valve.
|
|
||||
| OK | |
| 19. INSPECT TORQUE CONVERTER ASSEMBLY |
Check the torque converter assembly (Click here).
- OK:
- The torque converter assembly operates normally.
|
|
||||
| OK | ||
| ||
| 20. INSPECT SHIFT SOLENOID VALVE SLT |
Remove shift solenoid valve SLT.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
5.0 to 5.6 Ω
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
- OK:
Measurement Condition
Specified Condition
- Battery positive (+) with a 21 W bulb → Terminal 2
- Battery negative (-) → Terminal 1
Valve moves and makes an operating noise
- Battery positive (+) with a 21 W bulb → Terminal 2
| *a |
Component without harness connected (Shift Solenoid Valve SLT) |
|
|
||||
| OK | |
| 21. INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
- OK:
- There are no foreign objects on each valve.
|
|
||||
| OK | |
| 22. INSPECT TORQUE CONVERTER ASSEMBLY |
Check the torque converter assembly (Click here).
- OK:
- The torque converter assembly operates normally.
|
|
||||
| OK | ||
| ||
