P0982 Shift Solenoid "D" Control Circuit Low (Shift Solenoid Valve S4)
Diagnostic trouble codes · Vehicles built from Jan 2012
Also covers:
- P0983 Shift Solenoid "D" Control Circuit High (Shift Solenoid Valve S4)
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
Shifting from 1st to 6th is performed in combination with ON and OFF operation of the shift solenoid valves SL1, SL2, S1, S2, S3, S4 and SR, which are controlled by the ECM. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated safely. Also, the ECM stops sending the current to the open or short circuited solenoid (Click here).| DTC Code |
DTC Detection Condition |
Trouble Area |
| P0982 |
ECM detects short in solenoid valve S4 circuit 2 times when solenoid valve S4 is operated (1 trip detection logic). |
|
| P0983 |
ECM detects open in solenoid valve S4 circuit 2 times when solenoid valve S4 is not operated (1 trip detection logic). |
|
MONITOR DESCRIPTION
These DTCs indicate an open or short in the shift solenoid valve S4 circuit. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores the DTC. When the shift solenoid valve S4 is ON, if its resistance is 8 Ω or less, the ECM determines there is a short in the shift solenoid valve S4 circuit.When the shift solenoid valve S4 is OFF, if its resistance is 100 kΩ or more, the ECM determines there is an open in the shift solenoid valve S4 circuit (Click here).
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Shift solenoid valve S4 is turned ON/OFF normally when the shift lever is in D.
ECM gear shift command
1st
2nd
3rd
4th
5th
6th
Shift solenoid valve S4
OFF
OFF
OFF
OFF
ON
ON
| 1. INSPECT NO. 1 TRANSMISSION WIRE (SHIFT SOLENOID VALVE S4) |
Disconnect the No. 1 transmission wire connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
14 (S4) - Body ground
20°C (68°F)
11 to 15 Ω
Text in Illustration *a
Component without harness connected
(No. 1 Transmission Wire)
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM) |
Disconnect the ECM connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
C45-5 (S4) - Body ground
20°C (68°F)
11 to 15 Ω
Text in Illustration *a
Front view of wire harness connector
(to ECM)
|
|
||||
| OK | ||
| ||
| 3. INSPECT SHIFT SOLENOID VALVE S4 |
Remove the shift solenoid valve S4.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
Shift solenoid valve S4 connector terminal - Shift solenoid valve S4 body
20°C (68°F)
11 to 15 Ω
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
- OK:
Measurement Condition
Specified Condition
- Battery positive (+) → Shift solenoid valve S4 connector
- Battery negative (-) → Shift solenoid valve S4 body
Valve moves and makes an operating noise
- Battery positive (+) → Shift solenoid valve S4 connector
| *a |
Component without harness connected (Shift Solenoid Valve S4) |
|
|
||||
| OK | ||
| ||
