2011-2013 Land Cruiser · Service Manual Drivetrain

P0778 Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2)

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

Shifting from 1st to 5th is performed in combination with the ON and OFF operation of the shift solenoid valves SL1, SL2, S1, S2, S3, S4 and SR, which are controlled by the ECM. If an open or short circuit occurs in the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated safely (Click here).
DTC Code
DTC Detection Condition
Trouble Area
P0778
The ECM checks for an open or short in the shift solenoid valve SL2 circuit while driving and shifting gears (1 trip detection logic).
Output signal duty ratio equals to 100%.

HINT:
SL2 output signal duty ratio is less than 100% under normal condition.

  1. Open or short in shift solenoid valve SL2 circuit
  2. Shift solenoid valve SL2
  3. ECM
Reference: Inspect using an oscilloscope.
Check the waveform of the ECM connector.
C140833E11

Standard:
Terminal No. (Symbol)
Tool Setting
Condition
Specified Condition
C45-12 (SL2+) - C45-13 (SL2-)
5 V/DIV., 1 msec./DIV.
Engine is idling
Refer to illustration


MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SL2 circuit. The ECM commands gear shifts by turning the shift solenoid valves ON/OFF. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores the DTC. Also, the ECM performs the fail-safe function and turns the other shift solenoid valves that are in good condition ON/OFF. In the case of an open or short circuit, the ECM stops sending the current to the open or short circuited solenoid.
While driving and shifting gears, if the ECM detects an open or short in the shift solenoid valve SL2 circuit, the ECM determines there is a malfunction (Click here).

WIRING DIAGRAM

C219459E06

INSPECTION PROCEDURE


HINT:
Shift solenoid valve SL2 is turned ON/OFF normally when the shift lever is in D.
ECM gear shift command
1st
2nd
3rd
4th
5th
6th
Shift solenoid valve SL2
ON
ON
ON
ON
OFF
OFF


1. INSPECT NO. 2 TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL2)

  1. C219458E01
    Disconnect the C96 No. 2 transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (SL2+) - 4 (SL2-)
    20°C (68°F)
    5.0 to 5.6 Ω
    2 (SL2+) - Body ground
    Always
    10 kΩ or higher
    4 (SL2-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (No. 2 Transmission Wire)



NG
Go to step 3
OK


2. CHECK HARNESS AND CONNECTOR (NO. 2 TRANSMISSION WIRE - ECM)

  1. C219456E20
    Disconnect the C45 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C45-12 (SL2+) - C45-13 (SL2-)
    20°C (68°F)
    5.0 to 5.6 Ω
    C45-12 (SL2+) - Body ground
    Always
    10 kΩ or higher
    C45-13 (SL2-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

3. INSPECT SHIFT SOLENOID VALVE SL2

  1. C197715E12
    Remove the shift solenoid valve SL2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) with a 21 W bulb → Terminal 1
    2. Battery negative (-) → Terminal 2
    Valve moves and makes an operating noise

Text in Illustration 
*a
Component without harness connected
(Shift Solenoid Valve SL2)


NG
REPLACE SHIFT SOLENOID VALVE SL2 (Click here)
OK

REPAIR OR REPLACE NO. 2 TRANSMISSION WIRE (Click here)


← P0766 Shift Solenoid "D" Performance (Shift Solenoid Valve S4) (+ P0776) (from Jan 2012)P0778 Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2) (from Jan 2012) →