2011-2013 Land Cruiser · Service Manual Drivetrain

Transmission Control Switch Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

When moving the shift lever to S using the transmission control switch, it is possible to switch the shift range between "1" (1st range) and "5" (5th range).
Shifting to "+" once raises the shift range by one, and shifting to "-" lowers the shift range by one.

WIRING DIAGRAM

C176192E07

INSPECTION PROCEDURE


1. INSPECT TRANSMISSION CONTROL SWITCH

  1. C146679E06
    Disconnect the E52 transmission control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (IG) - 7 (S)
    Shift lever in S, "+" or "-"
    Below 1 Ω
    2 (SFTU) - 5 (E)
    Shift lever held in "+"
    (Up-shift)
    Below 1 Ω
    1 (SFTD) - 5 (E)
    Shift lever held in "-"
    (Down-shift)
    Below 1 Ω
    3 (IG) - 7 (S)
    Shift lever not in S, "+" or "-"
    10 kΩ or higher
    2 (SFTU) - 5 (E)
    Shift lever in S
    10 kΩ or higher
    1 (SFTD) - 5 (E)
    Shift lever in S
    10 kΩ or higher



NG
REPLACE TRANSMISSION CONTROL SWITCH (LOWER SHIFT LEVER ASSEMBLY) (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY, BODY GROUND)

  1. C146729E12
    Disconnect the E52 transmission control switch connector.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E52-3 (IG) - Body ground
    Engine switch on (IG)
    11 to 14 V
    E52-3 (IG) - Body ground
    Engine switch off
    Below 1 V

  1. Turn the engine switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E52-5 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

  1. C177782E05
    Disconnect the A38 ECM connector (for LHD).

  1. Disconnect the A52 ECM connector (for RHD).

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    A38-25 (S) - Body ground
    1. Engine switch on (IG)
    2. Shift lever in S, "+" or "-"
    11 to 14 V
    A38-25 (S) - Body ground
    1. Engine switch on (IG)
    2. Shift lever not in S, "+" or "-"
    Below 1 V
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    A52-25 (S) - Body ground
    1. Engine switch on (IG)
    2. Shift lever in S, "+" or "-"
    11 to 14 V
    A52-25 (S) - Body ground
    1. Engine switch on (IG)
    2. Shift lever not in S, "+" or "-"
    Below 1 V

  1. Turn the engine switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    A38-38 (SFTU) - Body ground
    Shift lever held in "+"
    (Up-shift)
    Below 1 Ω
    A38-27 (SFTD) - Body ground
    Shift lever held in "-"
    (Down-shift)
    Below 1 Ω
    A38-38 (SFTU) - Body ground
    Shift lever in S
    10 kΩ or higher
    A38-27 (SFTD) - Body ground
    Shift lever in S
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    A52-38 (SFTU) - Body ground
    Shift lever held in "+"
    (Up-shift)
    Below 1 Ω
    A52-27 (SFTD) - Body ground
    Shift lever held in "-"
    (Down-shift)
    Below 1 Ω
    A52-38 (SFTU) - Body ground
    Shift lever in S
    10 kΩ or higher
    A52-27 (SFTD) - Body ground
    Shift lever in S
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← U0100 Lost Communication with ECM / PCM "A" (Sep 2011 – Dec 2011)Pattern Select Switch Power Mode Circuit (Sep 2011 – Dec 2011) →