2011-2013 Land Cruiser · Service Manual Drivetrain

Transmission Control Switch Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

When moving the shift lever to S using the transmission control switch, it is possible to switch the shift range among "1" (1st range) and "6" (6th range).
Shifting to "+" once raises the shift range by one, and shifting to "-" lowers the shift range by one.

WIRING DIAGRAM

C176192E18

INSPECTION PROCEDURE


1. INSPECT TRANSMISSION CONTROL SWITCH

  1. C203344E20
    Disconnect the E52 transmission control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (IG) - 7 (S)
    Shift lever in S, "+" and "-"
    Below 1 Ω
    2 (SFTU) - 5 (E)
    Shift lever continuously in "+"
    (Up-shift)
    Below 1 Ω
    1 (SFTD) - 5 (E)
    Shift lever continuously in "-"
    (Down-shift)
    Below 1 Ω
    3 (IG) - 7 (S)
    Shift lever not in S, "+" and "-"
    10 kΩ or higher
    2 (SFTU) - 5 (E)
    Shift lever in S
    10 kΩ or higher
    1 (SFTD) - 5 (E)
    Shift lever in S
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Control Switch)



NG
REPLACE TRANSMISSION CONTROL SWITCH (LOWER SHIFT LEVER ASSEMBLY) (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY, BODY GROUND)

  1. C203343E36
    Disconnect the E52 transmission control switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E52-3 (IG) - Body ground
    Engine switch on (IG)
    11 to 14 V
    E52-3 (IG) - Body ground
    Engine switch off
    Below 1 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E52-5 (E) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Transmission Control Switch)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

  1. C197708E44
    Disconnect the A38 ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A38-25 (S) - Body ground
    1. Engine switch on (IG)
    2. Shift lever in S, "+" and "-"
    11 to 14 V
    A38-25 (S) - Body ground
    1. Engine switch on (IG)
    2. Shift lever not in S, "+" and "-"
    Below 1 V

  1. Turn the engine switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A38-38 (SFTU) - Body ground
    Shift lever continuously in "+"
    (Up-shift)
    Below 1 Ω
    A38-27 (SFTD) - Body ground
    Shift lever continuously in "-"
    (Down-shift)
    Below 1 Ω
    A38-38 (SFTU) - Body ground
    Shift lever in S
    10 kΩ or higher
    A38-27 (SFTD) - Body ground
    Shift lever in S
    10 kΩ or higher

Text in Illustration 
*a
Front view of wire harness connector
(to ECM)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← P2759 Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU) (from Jan 2012)Transmission Control Switch Circuit (from Jan 2012) →