Transmission Control Switch Circuit
Circuit diagnosis · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
When moving the shift lever to S using the transmission control switch, it is possible to switch the shift range between "1" (1st range) and "5" (5th range).Shifting to "+" once raises the shift range by one, and shifting to "-" lowers the shift range by one.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. INSPECT TRANSMISSION CONTROL SWITCH |
Disconnect the transmission control switch connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
3 (IG) - 7 (S)
Shift lever in S, "+" or "-"
Below 1 Ω
2 (SFTU) - 5 (E)
Shift lever held in "+"
(Up-shift)
Below 1 Ω
1 (SFTD) - 5 (E)
Shift lever held in "-"
(Down-shift)
Below 1 Ω
3 (IG) - 7 (S)
Shift lever not in S, "+" or "-"
10 kΩ or higher
2 (SFTU) - 5 (E)
Shift lever in S
10 kΩ or higher
1 (SFTD) - 5 (E)
Shift lever in S
10 kΩ or higher
Text in Illustration *a
Front view of wire harness connector
(to Transmission Control Switch)
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY, BODY GROUND) |
Disconnect the transmission control switch connector.

Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
E52-3 (IG) - Body ground
Engine switch on (IG)
11 to 14 V
E52-3 (IG) - Body ground
Engine switch off
Below 1 V
Turn the engine switch off.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E52-5 (E) - Body ground
Always
Below 1 Ω
| *a |
Front view of wire harness connector (to Transmission Control Switch) |
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM) |
Disconnect the ECM connector.

Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
A38-25 (S) - Body ground
- Engine switch on (IG)
- Shift lever in S, "+" or "-"
11 to 14 V
A38-25 (S) - Body ground
- Engine switch on (IG)
- Shift lever not in S, "+" or "-"
Below 1 V
- Engine switch on (IG)
Turn the engine switch off.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A38-38 (SFTU) - Body ground
Shift lever held in "+"
(Up-shift)
Below 1 Ω
A38-27 (SFTD) - Body ground
Shift lever held in "-"
(Down-shift)
Below 1 Ω
A38-38 (SFTU) - Body ground
Shift lever in S
10 kΩ or higher
A38-27 (SFTD) - Body ground
Shift lever in S
10 kΩ or higher
| *a |
Front view of wire harness connector (to ECM) |
|
|
||||
| OK | ||
| ||
