2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

INSPECTION

Inspection · Vehicles built from Jan 2012


INSPECT FUEL INJECTOR ASSEMBLY
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    11.6 to 12.4 Ω

    If the result is not as specified, replace the fuel injector assembly.

  1. Inspect the injection volume.

    CAUTION:
    This test involves high-pressure fuel and electricity. Take all precautions regarding safe handling of both the fuel and the electricity. Perform this test in a safe area and avoid any sparks or flames. Do not smoke.


    1. A088228E27
      Connect SST to the fuel pipe.
      SST
      09268-31014   (09268-41500, 09268-41700, 95336-08070)
      Text in Illustration 
      *1
      SST (Hose)
      *2
      SST (Hose Band)
      *3
      SST (Fuel Tube Connector)
      *4
      Fuel Pipe

    2. A149192E10
      Install the O-ring to the fuel injector.

    3. Install SST and the tube to the fuel injector.

      SST
      09268-31014   (09268-41300, 09268-41600, 09268-41700, 95336-08070)
      Text in Illustration 
      *1
      SST (Hose)
      *2
      SST (Hose Band)
      *3
      SST (Adapter)
      *4
      O-ring
      *5
      Vinyl Tube
      *6
      SST (Clamp)

    4. A274395E01
      Pass SST (tie band) through the loop on the handle of SST (clamp) to secure SST (clamp) to SST (adapter).
      SST
      09268-31014   (09268-41800)
      Text in Illustration 
      *1
      Lock
      *2
      SST (Tie Band)

      NOTICE:
      1. As SST (tie band) does not completely prevent SST (clamp) from becoming loose, do not subject the parts to any impacts while using them.
      2. Before using SST (tie band), make sure that there is no deterioration, damage or cracks. If there are any abnormalities, replace SST.

      HINT:
      When removing SST (tie band), disengage the lock.

    5. Check that SST (clamp) and SST (adapter) cannot be easily separated.

    6. Install a vinyl tube to the injector.

    7. Put the injector into a graduated cylinder.

      CAUTION:
      Install a strong rubber tube to the injector to prevent gasoline from splashing.

    8. Operate the fuel pump (Click here).

    9. A149193E09
      Connect SST (EFI inspection wire I) to the injector and battery for 15 seconds, and then measure the injection volume with the graduated cylinder. Test each injector 2 or 3 times.
      SST
      09842-30090  

      Standard injection volume:
      82 to 99 cc (5.0 to 6.0 cu in.) per 15 seconds

      Difference between each injector:
      17 cc (1.0 cu in.) or less

      Text in Illustration 
      *1
      SST (EFI Inspection Wire I)
      V100135
      Connect

      NOTICE:
      1. Make sure that SST (EFI inspection wire I) is securely connected.
      2. Always turn the voltage on and off on the battery side, not the fuel pump side.

      If the injection volume is not as specified, replace the injector assembly.

  1. Check for leakage.

    1. In the condition above, disconnect the tester probes of SST (wire) from the battery and check for fuel leakage from the injector.

      Standard fuel leakage:
      1 drop or less in 12 minutes

← REMOVAL (from Jan 2012)INSTALLATION (from Jan 2012) →