2011-2013 Land Cruiser · Service Manual Vehicle Interior

B2001 Short to GND in Seat Belt Motor RH Circuit

Diagnostic trouble codes · Vehicles built from Jan 2012

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The seat belt control ECU receives information from the master cylinder solenoid (skid control ECU) via the CAN communication line and tightens the seat belt by operating the motor in the front seat outer belt assembly RH or LH.
DTC Code
DTC Detection Condition
Trouble Area
B2001
  1. Short to ground in seat belt motor RH circuit continues for 1 second or more.
  2. Short in seat belt motor RH circuit.
  1. Front seat outer belt assembly RH
  2. Harness or connector
  3. Seat belt control ECU
B2006
  1. Short to ground in seat belt motor LH circuit continues for 1 second or more.
  2. Short in seat belt motor LH circuit.
  1. Front seat outer belt assembly LH
  2. Harness or connector
  3. Seat belt control ECU

WIRING DIAGRAM

E149036E01
E149036E02

INSPECTION PROCEDURE

CAUTION:
The pretensioner is built into the front seat outer belt assembly. Be sure to follow the correct inspection procedure, as failure to follow the correct procedure (such as inspection of incorrect connectors) may deploy the pretensioner.


1. CHECK SEAT BELT CONTROL ECU

  1. E149071E01
    Disconnect the E41 seat belt control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH 
    Tester Connection
    Condition
    Specified Condition
    E41-3 (MOL+) - Body ground
    Always
    1 MΩ or higher
    E41-4 (MOL-) - Body ground
    for RH 
    Tester Connection
    Condition
    Specified Condition
    E41-1 (MOR-) - Body ground
    Always
    1 MΩ or higher
    E41-2 (MOR+) - Body ground

    Result 
    Result
    Proceed to
    OK
    (for LHD)
    A
    OK
    (for RHD)
    B
    NG
    C



B
REPLACE SEAT BELT CONTROL ECU (Click here)

C
Go to step 2
A

REPLACE SEAT BELT CONTROL ECU (Click here)

2. CHECK HARNESS AND CONNECTOR (FRONT SEAT OUTER BELT - SEAT BELT CONTROL ECU)

  1. E149038E02
    Disconnect the E41 seat belt control ECU connector.

  1. Disconnect the K11*1 or L5*2 front seat outer belt connector.

    HINT:
    1. *1: for LH
    2. *2: for RH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH 
    Tester Connection
    Condition
    Specified Condition
    K11-1 (MOL+) - Body ground
    Always
    1 MΩ or higher
    K11-2 (MOL-) - Body ground
    for RH 
    Tester Connection
    Condition
    Specified Condition
    L5-1 (MOR+) - Body ground
    Always
    1 MΩ or higher
    L5-2 (MOR-) - Body ground

    Result 
    Result
    Proceed to
    OK
    (for DTC B2001)
    A
    OK
    (for DTC B2006)
    B
    NG
    C



B
REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH (Click here)


← B2001 Short to GND in Seat Belt Motor RH Circuit (+ B2006) (Sep 2011 – Dec 2011)B2002 Open in Seat Belt Motor RH Circuit (+ B2007) (Sep 2011 – Dec 2011) →