FAIL-SAFE CHART
System information · Vehicles built from Sep 2011
| POWER WINDOW OPERATION IN FAIL-SAFE MODE |
- HINT:
- If the pulse sensor built into the power window regulator motor malfunctions, the power window control system enters fail-safe mode.
The pulse sensor for the jam protection function has problems and the window position or the learned value is abnormal.
- HINT:
- The power window control system prohibits the following power window operations when the pulse sensor for the jam protection function has problems and the window position or the learned value is abnormal.
Multiplex Network Master Switch Power Window Operation
Condition
Ignition Switch ON
Ignition Switch off
(Key-off operation permitted)
Ignition Switch off
(Key-off operation prohibited)
Manual up (Driver side door window)
X
X
-
Manual down (Driver side door window)
○*1
X
-
Auto up (Driver side door window)
(hold switch at auto up position)
○*2
X
-
Auto up (Driver side door window)
X
X
-
Auto down (Driver side door window)
X
X
-
Manual up (Remote switch operation)
X
X
-
Manual down (Remote switch operation)
X
X
-
Auto up (Remote switch operation)
(hold switch at auto up position)
X
X
-
Auto up (Remote switch operation)
X
X
-
Auto down (Remote switch operation)
X
X
-
- HINT:
- ○: Operative
- X: Operation prohibited
- *1: Jam protection not operative
- *2: In manual mode and jam protection not operative
- ○: Operative
Power window switch LED control
- HINT:
- During normal operation (fail-safe is not operating), or during fail-safe mode when there is a pulse sensor malfunction or the window position or learned value is abnormal, the LED illuminates as shown in the illustration.
- for driver side:


Fail-safe Deactivation Condition
- When the pulse sensor is normal, to deactivate fail-safe mode, pull up the power window switch to the auto up position and hold it for at least 1 second to fully close the window from the fully open position. As a result, the auto up/down function will return.
- When the pulse sensor is normal, to deactivate fail-safe mode, pull up the power window switch to the auto up position and hold it for at least 1 second to fully close the window from the fully open position. As a result, the auto up/down function will return.
Initialization failure
- HINT:
- During initialization of the power window regulator motor ECU, when the window position or initialization complete status cannot be properly read from the EEPROM, the power window control system prohibits the following operations.
Multiplex Network Master Switch Power Window Operation
Condition
Ignition Switch ON
Ignition Switch off
(Key-off operation permitted)
Ignition Switch off
(Key-off operation prohibited)
Manual up (Driver side door window)
X
X
-
Manual down (Driver side door window)
○*1
X
-
Auto up (Driver side door window)
(hold switch at auto up position)
○*2
X
-
Auto up (Driver side door window)
X
X
-
Auto down (Driver side door window)
X
X
-
Manual up (Remote switch operation)
X
X
-
Manual down (Remote switch operation)
X
X
-
Auto up (Remote switch operation)
(hold switch at auto up position)
X
X
-
Auto up (Remote switch operation)
X
X
-
Auto down (Remote switch operation)
X
X
-
- HINT:
- ○: Operative
- X: Operation prohibited
- *1: Jam protection not operative
- *2: In manual mode and jam protection not operative
- ○: Operative
Power window switch LED control
- HINT:
- During initialization of the power window regulator motor ECU, when the window position or initialization complete status cannot be properly read from the EEPROM during fail-safe mode, the LED illuminates as shown in the illustration.
- for driver side:


LIN communication failure
- HINT:
- If the LIN communication line malfunctions (communication stop), the power window control system prohibits the following operations.
Multiplex Network Master Switch Power Window Operation
Ignition Switch ON
Manual up
○*1
Manual down
○*2
Auto up (hold switch at auto up position)
○*1
Auto up
○*1
Auto down
○*2
- HINT:
- ○: Operative
- X: Operation prohibited
- *1: Jam protection operative
- *2: Jam protection not operative
- Remote up/down function does not operate.
- ○: Operative
LIN communication failure and pulse sensor failure
- HINT:
- If the LIN communication line malfunctions (communication stop) and the pulse sensor for the jam protection function has problems, the power window control system prohibits the following operations.
Multiplex Network Master Switch Power Window Operation
Always
Manual up
X
Manual down
X
Auto up (hold switch at auto up position)
X
Auto up
X
Auto down
X
- HINT:
- ○: Operative
- X: Operation prohibited
- Driver side door window: When there is no jam protection control due to a LIN communication failure, the manual up and auto up functions will not operate.
- Remote switch operation: Not operative during LIN communication failure.
- ○: Operative
LIN communication failure and window position, learned value abnormal or initialization failure
- HINT:
- If the LIN communication line malfunctions (communication stop) and the window position or the learned value is abnormal, the power window control system prohibits the following operations.
Multiplex Network Master Switch Power Window Operation
Always
Manual up
○*1
Manual down
○*2
Auto up (hold switch at auto up position)
○*1
Auto up
-
Auto down
-
- HINT:
- ○: Operative
- *1: Jam protection operative and window reverses direction upon reaching the fully closed position
- *2: Jam protection not operative
- Remote switch operation: Operation is not possible during a LIN communication failure.
- ○: Operative