P0504 Brake Switch "A" / "B" Correlation
Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.- HINT:
- The normal signal conditions are as shown in the table below.
Signal (ECM Terminal)
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF
- [OFF] denotes ground potential.
- [ON] denotes battery potential (+B).
- On the intelligent tester, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.
- [OFF] denotes ground potential.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| P0504 |
Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic): (a) The engine switch is on (IG). (b) The brake pedal is released. (c) The STP signal is OFF when the ST1- signal is OFF. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- STP signal conditions can be checked using the intelligent tester.
- Connect the tester to the DLC3.
- Turn the engine switch on (IG).
- Turn the tester on.
- Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Stop Light Switch and ST1.
- Check the Data List indication when the brake pedal is depressed and released.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| Brake Pedal Operation |
Stop Light Switch |
ST1 |
| Depressed |
ON |
ON |
| Released |
OFF |
OFF |
| 1. CHECK STOP LIGHT SWITCH ASSEMBLY (B+ VOLTAGE) |
![]() ![]() |
Disconnect the A30 stop light switch connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A30-2 - Body ground
Always
11 to 14 V
A30-3 - Body ground
Engine switch on (IG)
11 to 14 V
|
|
||||
| OK | |
| 2. INSPECT STOP LIGHT SWITCH ASSEMBLY |
![]() ![]() |
Remove the stop light switch.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 2
Pin not pushed
Below 1 Ω
Pin pushed
10 kΩ or higher
3 - 4
Pin not pushed
10 kΩ or higher
Pin pushed
Below 1 Ω
|
|
||||
| OK | |
| 3. CHECK ECM (STP AND ST1 - VOLTAGE) |
![]() ![]() |
Disconnect the A38 or A53 ECM connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
A38-35 (ST1-) - Body ground
Brake pedal released
11 to 14 V
Brake pedal depressed
0 to 3 V
A38-36 (STP) - Body ground
Brake pedal released
0 to 3 V
Brake pedal depressed
11 to 14 V
|
|
||||
| OK | ||
| ||
| 4. INSPECT FUSE (STOP AND IGN) |
![]() ![]() |
Remove the STOP and IGN fuses from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
STOP fuse
Always
Below 1 Ω
IGN fuse
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||




