2011-2013 Land Cruiser · Service Manual Steering

CALIBRATION

Troubleshooting · Vehicles built from Sep 2011

NOTICE:
Use this procedure to center the steering wheel if:
  1. The steering actuator assembly has been replaced.
  2. The steering control ECU has been replaced.
  3. The steering column or steering intermediate shaft has been disconnected.
  4. The steering wheel is still off-center after completing the steering angle sensor initialization.


VGRS SYSTEM CALIBRATION PROCEDURE (WHEN USING SST CHECK WIRE)

1.FACE TIRES STRAIGHT AHEAD

    NOTICE:
    Drive the vehicle to confirm that the steering wheel is centered.

NEXT

2.CHECK DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC C1591/51 is not output
    A
    DTC C1591/51 is output
    B


B.
A

3.PERFORM ACTUATOR ANGLE INITIALIZATION
    SST
    09843-18040  

    NOTICE:
    If the procedures from *1 to *2 are not completed within 1 minute, or if errors are made during these procedures, perform the initialization again from the beginning.

  1. H102392E81
    Start the engine.

  2. Center the steering wheel.

  3. Using SST, connect terminals 12 (TS) and 4 (CG), and 13 (TC) and 4 (CG) of the DLC3.*1

  4. Disconnect SST from terminal 12 (TS) of the DLC3, and turn the steering wheel to the left 180° or more.

  5. Connect SST to terminal 12 (TS) of the DLC3.

  6. Disconnect SST from terminal 13 (TC) of the DLC3, and turn the steering wheel to the right 180° or more.

  7. Connect SST to terminal 13 (TC) of the DLC3.*2

    HINT:
    If the master warning light comes on, DTC C1591/51 is stored.

  8. Disconnect SST from the DLC3.

  9. Turn the engine switch off.

NEXT

4.FACE TIRES STRAIGHT AHEAD
  1. Confirm that the steering wheel is centered when facing the tires straight ahead.

    NOTICE:
    Drive the vehicle to confirm that the steering wheel is centered.

    Result 
    Result
    Proceed to
    Steering wheel is off-center
    A
    Steering wheel is centered
    B


B.
A

5.UNLOCK STEERING ACTUATOR

    NOTICE:
    Make sure the engine is not running.

  1. Turn the engine switch off.

  2. Disconnect the cable from the negative (-) battery terminal.

  3. C140769E04
    Disconnect the E80 connector from the steering actuator.

  4. Connect a jumper wire from terminal 7 (LV+) of the steering actuator to the positive (+) 12 V battery terminal and another jumper wire from terminal 16 (LG+) of the steering actuator to the negative (-) 12 V battery terminal.

    NOTICE:
    Do not apply voltage for more than 3 minutes.

NEXT

6.STEERING CENTER ADJUSTMENT
  1. Center the steering wheel.

    NOTICE:
    If the centering of the spiral cable was not confirmed when the steering wheel was installed, confirm the centering of the spiral cable (Click here).

NEXT

7.LOCK STEERING ACTUATOR
  1. Disconnect the positive (+) and negative (-) 12 V battery jumper wires from the steering actuator.

  2. Connect the E80 connector to the steering actuator.

  3. Connect the cable to the negative (-) battery terminal.

  4. Turn the steering wheel approximately 3° to the left and right. Confirm that the reaction force can be felt.

    NOTICE:
    1. If the above procedures are not followed correctly, a DTC will be stored. If a DTC is stored, perform the above procedures again and then check for DTCs.
    2. Perform these procedures with the engine switch off.

NEXT

8.ADJUST ACTUATOR ANGLE

    HINT:
    Activating and ending test mode will complete actuator angle adjustment.

  1. Make sure the engine switch is off.

    NOTICE:
    Do not touch the steering wheel during these procedures.

  2. H102392E80
    Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.

  3. SST
    09843-18040  
  4. Turn the engine switch on (IG).

  5. Confirm that "VGRS Test Mode" is displayed on the multi-information display when test mode is activated.

    HINT:
    Wait approximately 5 seconds.

  6. Turn the engine switch off.

  7. Disconnect SST from terminals 12 (TS) and 4 (CG) of the DLC3.

  8. Turn the engine switch on (IG) again.

NEXT

9.CHECK MASTER WARNING LIGHT
  1. Confirm that the master warning light is off.

  2. Turn the engine switch off, then on (IG).

  3. Confirm that the master warning light is operating normally.

NEXT

10.CHECK STEERING WHEEL OPERATION
  1. Start the engine.

  2. Perform the steering angle sensor initialization (Click here).

  3. Turn the steering wheel from lock to lock and check that it rotates approximately 2.7 turns.

  4. Drive the vehicle and confirm that the steering wheel is centered.

NEXT


VGRS SYSTEM CALIBRATION PROCEDURE (WHEN USING INTELLIGENT TESTER)

1.FACE TIRES STRAIGHT AHEAD

    NOTICE:
    Drive the vehicle to confirm that the steering wheel is centered.

NEXT

2.PERFORM VGRS SYSTEM CALIBRATION
  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the tester on.

  4. Enter the following menus: Chassis / VGRS / Utility / Steering Angle Adjust.Then, press "Next".

  5. Follow the instructions on the tester, and press "Next".

    NOTICE:
    Press the "Next" key even if DTC C15B4/71 is output.

  6. Follow the instructions on the tester, and press "Next".

  7. Follow the instructions on the tester, and press "Next".

    NOTICE:
    Ensure that the engine switch is off.

  8. Follow the instructions on the tester, and press "Next".

  9. Follow the instructions on the tester, and press "Next".

    NOTICE:
    If the centering of the spiral cable was not confirmed when the steering wheel was installed, confirm the centering of the spiral cable (Click here).

  10. Follow the instructions on the tester, and press "Next".

    NOTICE:
    Do not touch the steering wheel during these procedures.

  11. Follow the instructions on the tester, and press "Next".

  12. Follow the instructions on the tester, and press "Next".

    NOTICE:
    Do not touch the steering wheel during these procedures.

  13. "NOW CALIBRATING" is displayed and the display switches automatically to the next screen.

    NOTICE:
    Do not touch the steering wheel during these procedures.

  14. "Steering Angle Adjust is complete." is displayed. Then, check that the VGRS system calibration is completed normally.

  15. Select "Exit" to return the display to the "MENU" screen.

NEXT

3.CHECK MASTER WARNING LIGHT
  1. Confirm that the master warning light is off.

  2. Turn the engine switch off.

  3. Disconnect the intelligent tester from the DLC3.

  4. Turn the engine switch on (IG).

  5. Confirm that the master warning light is operating normally.

NEXT

4.CHECK STEERING WHEEL OPERATION
  1. Start the engine.

  2. Perform the steering angle sensor initialization (Click here).

  3. Turn the steering wheel from lock to lock and check that it rotates approximately 2.7 turns.

  4. Drive the vehicle and confirm that the steering wheel is centered.

NEXT

← INITIALIZATION (from Sep 2011)TEST MODE PROCEDURE (Sep 2011 – Dec 2011) →