2011-2013 Land Cruiser · Service Manual Vehicle Interior

TERMINALS OF ECU

System information · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
B122343E14
  1. Disconnect the E29 ECU connector.

  2. Measure the resistance and voltage of the wire harness side connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E29-17 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    E29-1 (+B) - Body ground
    B - Body ground
    +B power supply
    Always
    11 to 14 V
    E29-18 (IG) - Body ground
    B - Body ground
    Ignition power supply
    Engine switch off
    Below 1 V
    Engine switch on (IG)
    11 to 14 V
    E29-3 (TSW1) - E29-17 (E)
    G - W-B
    Door outside handle (driver side) lock switch signal
    Switch released
    10 kΩ or higher
    Switch pressed in
    Below 1 Ω
    E29-4 (TSW2) - E29-17 (E)
    BR - W-B
    Door outside handle (front passenger side) lock switch signal
    Switch released
    10 kΩ or higher
    Switch pressed in
    Below 1 Ω
    E30-25 (TSW3) - E29-17 (E)*3
    G - W-B
    1. Door outside handle (rear LH) lock switch signal*1
    2. Door outside handle (rear RH) lock switch signal*2
    Switch released
    10 kΩ or higher
    Switch pressed in
    Below 1 Ω
    E30-26 (TSW4) - E29-17 (E)*3
    G - W-B
    1. Door outside handle (rear RH) lock switch signal*1
    2. Door outside handle (rear LH) lock switch signal*2
    Switch released
    10 kΩ or higher
    Switch pressed in
    Below 1 Ω
    E29-7 (TSW5) - E29-17 (E)
    L - W-B
    Back door lock switch signal
    Switch released
    10 kΩ or higher
    Switch pressed in
    Below 1 Ω
    E29-10 (LIN) - E29-17 (E)
    GR - W-B
    LIN line
    Always
    10 kΩ or higher
    E29-27 (CANH) - E29-17 (E)
    LG - W-B
    CAN line
    Always
    10 kΩ or higher
    E29-28 (CANL) - E29-17 (E)
    R - W-B
    CAN line
    Always
    10 kΩ or higher

    HINT:
    1. *1: for LHD
    2. *2: for RHD
    3. *3: For vehicles with entry function for rear doors.

    1. If the result is not as specified, the wire harness side may have a malfunction.

  3. Reconnect the E29 ECU connector.

  4. Measure the voltage of the connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E29-33 (CLG1) - E29-34 (CG1B)
    L - W
    Door electrical key oscillator (driver side) sensor signal
    All doors closed, all doors locked and engine switch off
    Alternating between 5 V and below 1 V
    Door unlocked or door open
    Below 1 V
    E29-22 (SEN1) - E29-17 (E)
    R - W-B
    Touch sensor detection signal
    Door outside handle touched
    11 to 14 V
    Door outside handle not touched
    Below 1 V
    E29-5 (SEL1) - E29-17 (E)
    Y - W-B
    Touch sensor activation control signal
    Key at least 5 m (16.4 ft.) away from door
    11 to 14 V
    Key moved near outside door handle
    Below 1 V
    E29-35 (CLG2) - E29-36 (CG2B)
    L - R
    Door electrical key oscillator (front passenger side) sensor signal
    All doors closed, all doors locked and engine switch off
    Alternating between 5 V and below 1 V
    Door unlocked or door open
    Below 1 V
    E29-23 (SEN2) - E29-17 (E)
    R - W-B
    Touch sensor detection signal
    Door outside handle touched
    11 to 14 V
    Door outside handle not touched
    Below 1 V
    E29-6 (SEL2) - E29-17 (E)
    Y - W-B
    Touch sensor activation control signal
    Key at least 5 m (16.4 ft.) away from door
    11 to 14 V
    Key moved near outside door handle
    Below 1 V
    E30-8 (CLG3) - E30-9 (CG3B)*3
    L - W
    1. Door electrical key oscillator (rear LH) sensor signal*1
    2. Door electrical key oscillator (rear RH) sensor signal*2
    All doors closed, all doors locked and engine switch off
    Alternating between 5 V and below 1 V
    Door unlocked or door open
    Below 1 V
    E30-28 (SEN3) - E29-17 (E)*3
    R - W-B
    Touch sensor detection signal
    Door outside handle touched
    11 to 14 V
    Door outside handle not touched
    Below 1 V
    E30-1 (SEL3) - E29-17 (E)*3
    Y - W-B
    Touch sensor activation control signal
    Key at least 5 m (16.4 ft.) away from door
    11 to 14 V
    Key moved near outside door handle
    Below 1 V
    E30-10 (CLG4) - E30-11 (CG4B)*3
    L - W
    1. Door electrical key oscillator (rear RH) sensor signal*1
    2. Door electrical key oscillator (rear LH) sensor signal*2
    All doors closed, all doors locked and engine switch off
    Alternating between 5 V and below 1 V
    Door unlocked or door open
    Below 1 V
    E30-27 (SEN4) - E29-17 (E)*3
    R - W-B
    Touch sensor detection signal
    Door outside handle touched
    11 to 14 V
    Door outside handle not touched
    Below 1 V
    E30-2 (SEL4) - E29-17 (E)*3
    Y - W-B
    Touch sensor activation control signal
    Key at least 5 m (16.4 ft.) away from door
    11 to 14 V
    Key moved near outside door handle
    Below 1 V
    E29-11 (CLG5) - E29-12 (CG5B)
    SB - V
    Indoor electrical key antenna (for front) sensor signal
    30 seconds after driver side door opened and closed, engine switch off
    Alternating between 5 V and below 1 V
    Within 30 seconds after driver side door opened and closed, engine switch off
    Below 1 V
    E29-13 (CLG6) - E29-14 (CG6B)
    R - SB
    Indoor electrical key antenna (for rear 1) sensor signal
    30 seconds after driver side door opened and closed, engine switch off
    Alternating between 5 V and below 1 V
    Within 30 seconds after driver side door opened and closed, engine switch off
    Below 1 V
    E29-15 (CLG7) - E29-16 (CG7B)
    GR - W
    Indoor electrical key antenna (for rear 2) sensor signal
    30 seconds after driver side door opened and closed, engine switch off
    Alternating between 5 V and below 1 V
    Within 30 seconds after driver side door opened and closed, engine switch off
    Below 1 V
    E29-31 (CLG8) - E29-32 (CG8B)
    G - GR
    Back door electrical key antenna (for outer) sensor signal
    Back door opener switch off
    Alternating between 5 V and below 1 V
    Back door opener switch on
    Below 1 V
    E29-29 (RCO) - E29-17 (E)
    B - W-B
    Door control receiver power source
    Engine switch off, all doors closed and transmitter switch not pressed → pressed
    Below 1 V → 4.6 to 5.4 V → Below 1 V
    E29-39 (RSSI) - E29-17 (E)
    L - W-B
    Door control receiver electric wave existence signal
    Engine switch off, all doors closed and transmitter switch not pressed → pressed
    11 to 14 V → Below 1 V
    E29-38 (RDA) - E29-17 (E)
    LG - W-B
    Door control receiver data input signal
    Engine switch off, all doors closed and transmitter switch not pressed → pressed
    Below 1 V → 11 to 14 V → Below 1 V
    E29-21 (BZR) - E29-17 (E)
    LG - W-B
    Wireless door lock buzzer signal
    Answer-back on
    Pulse generation
    Answer-back off
    Below 1 V

    HINT:
    1. *1: for LHD
    2. *2: for RHD
    3. *3: For vehicles with entry function for rear doors.

    1. If the result is not as specified, the ECU may have a malfunction.


CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)
C172609E03
  1. Disconnect the E1, E2, E3, 2A, 2B and 2D ECU connectors.

  2. Measure the resistance and voltage of the wire harness side connectors.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2D-62 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    E3-1 (GND3) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    2A-1 (ALTB) - Body ground
    B - Body ground
    ALTB power supply
    Always
    11 to 14 V
    2B-20 (BATB) - Body ground
    L - Body ground
    BATB power supply
    Always
    11 to 14 V
    E1-6 (AM1) - Body ground
    W - Body ground
    AM1 power supply
    Always
    11 to 14 V
    E2-1 (AM2) - Body ground
    W - Body ground
    AM2 power supply
    Always
    11 to 14 V
    2D-7 (IG) - Body ground
    G - Body ground
    IG1 signal
    Engine switch on (IG)
    11 to 14 V
    Engine switch off
    Below 1 V
    2D-8 (ACC) - Body ground
    GR - Body ground
    ACC signal
    Engine switch on (ACC)
    11 to 14 V
    Engine switch off
    Below 1 V
    E3-5 (CANH) - Body ground
    SB - Body ground
    CAN communication line
    Always
    10 kΩ or higher
    E3-6 (CANL) - Body ground
    B - Body ground
    CAN communication line
    Always
    10 kΩ or higher
    E3-15 (CANN) - Body ground
    R - Body ground
    CAN communication line
    Always
    10 kΩ or higher
    E3-16 (CANP) - Body ground
    GR - Body ground
    CAN communication line
    Always
    10 kΩ or higher
    2B-20 (LIN1) - Body ground
    GR - Body ground
    LIN communication line
    Always
    10 kΩ or higher
    E3-10 (LIN2) - Body ground
    G - Body ground
    LIN communication line
    Always
    10 kΩ or higher
    1. If the result is not as specified, the wire harness side may have a malfunction.

  3. Reconnect the E1, E2, E3, 2A, 2B and 2D ECU connectors.

  4. Measure the voltage of the connectors.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E1-24 (DCTY) - Body ground
    L - Body ground*1
    Y - Body ground*2
    Driver side door courtesy switch input
    Driver side door open
    Below 1 V
    Engine switch off, and driver side door courtesy switch off
    Pulse generation (see waveform 1 or 2)
    E2-21 (PCTY) - Body ground
    Y - Body ground*1
    L - Body ground*2
    Front passenger side door courtesy switch input
    Front passenger side door open
    Below 1 V
    Engine switch off, and passenger side door courtesy switch off
    Pulse generation (see waveform 3 or 4)
    2C-2 (LCTY) - Body ground
    W - Body ground
    Rear door LH courtesy light switch input
    Rear door LH open
    Below 1 V
    Engine switch off, and rear LH side door courtesy switch off
    Pulse generation (see waveform 5 or 6)
    E2-7 (RCTY) - Body ground
    G - Body ground
    Rear door RH courtesy light switch input
    Rear door RH open
    Below 1 V
    Engine switch off, and rear RH side door courtesy switch off
    Pulse generation (see waveform 7 or 8)
    E2-25 (BCTY) - Body ground
    W - Body ground
    Back door courtesy light switch input
    Back door open
    Below 1 V
    Engine switch off, and back door closed
    Pulse generation (see waveform 9 or 10)
    E3-4 (HAZ) - Body ground
    O - Body ground
    Hazard warning light signal
    Answer-back on
    Below 1 V
    Answer-back off
    11 to 14 V
    E1-26 (BDSU) - Body ground
    L - Body ground
    Back door opener switch input
    Back door lock opener switch off
    Below 1 V
    Back door lock opener switch on
    Pulse generation (see waveform 11 or 12)

    HINT:
    1. *1: for LHD
    2. *2: for RHD

    If the result is not as specified, the ECU may have a malfunction.

  5. B122376E01
    Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E1-24 (DCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and driver side door courtesy switch off

  6. B129408E01
    Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E1-24 (DCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and driver side door courtesy switch off

  7. B189909E01
    Using an oscilloscope, check waveform 3.
    Waveform 3 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E2-21 (PCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and passenger side door courtesy switch off

  8. B189910E01
    Using an oscilloscope, check waveform 4.
    Waveform 4 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E2-21 (PCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and passenger side door courtesy switch off

  9. B122376E01
    Using an oscilloscope, check waveform 5.
    Waveform 5 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    2C-2 (LCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and rear LH side door courtesy switch off

  10. B129408E01
    Using an oscilloscope, check waveform 6.
    Waveform 6 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    2C-2 (LCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and rear LH side door courtesy switch off

  11. B122376E01
    Using an oscilloscope, check waveform 7.
    Waveform 7 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E2-7 (RCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and rear RH side door courtesy switch off

  12. B129408E01
    Using an oscilloscope, check waveform 8.
    Waveform 8 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E2-7 (RCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and rear RH side door courtesy switch off

  13. B122376E01
    Using an oscilloscope, check waveform 9.
    Waveform 9 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E2-25 (BCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and back door closed

  14. B129408E01
    Using an oscilloscope, check waveform 10.
    Waveform 10 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E2-25 (BCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and back door closed

  15. B189909E01
    Using an oscilloscope, check waveform 11.
    Waveform 11 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E1-26 (BDSU) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and Back door lock opener switch on

  16. B189910E01
    Using an oscilloscope, check waveform 12.
    Waveform 12 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E1-26 (BDSU) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and Back door lock opener switch on

← PROBLEM SYMPTOMS TABLE (from Jan 2012)TERMINALS OF ECU (from Jan 2012) →