2011-2013 Land Cruiser · Service Manual Vehicle Interior

CUSTOMIZE PARAMETERS

Troubleshooting · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


CUSTOMIZING FUNCTION WITH INTELLIGENT TESTER

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current setting before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Customize Setting.

  5. Select the setting by referring to the table below.

    Entry & Start 
    Display
    Default
    Contents
    Setting
    Ignition Area
    (Entry ignition available area)
    ALL
    Function to choose the available area for the key to start the engine and cancel the steering lock.
    FRONT/ALL*
    Park Wait Time (Waiting time to permit unlocking door after locking)
    2.5s
    Function that sets the waiting time to permit unlocking the door after the door is locked with the entry lock function.
    0.5s/1.5s/2.5s/5s
    Back Door Opening Operation (Back door open mode when vehicle is locked)
    LONG
    Back door opening the operation.
    LONG/TWICE/OFF
    Warning 
    Display
    Default
    Contents
    Setting
    Passenger Take Key
    ON
    Warn a key is taken out by fellow passengers
    ON/OFF
    Key Low Battery Warning (Warn when key battery becomes weak)
    ON
    Function that warns the driver that the key battery power is low.
    ON/OFF
    Key Out Range Warning
    ON
    Warn Starting E/G when the key is out of range
    ON/OFF

    HINT:
    *: "FRONT" means front, and "ALL" means front, rear 1 and rear 2.


ENTRY UNLOCK MODE SWITCHING FUNCTION
  1. To use the entry unlock mode switching function, make sure the engine switch is off and simultaneously press and hold the lock switch on the key and another key switch for 5 seconds.

    1. When the switches are pressed and held for 5 seconds, the entry door unlock mode changes in the following order: all door unlock mode, driver door unlock mode.

    NOTICE:
    After pressing and holding the switches for 5 seconds, wait 5 seconds before performing the same procedure again.

    1. All door unlock mode (default):
      When a touch sensor is touched, all doors unlock.
    2. Driver door unlock mode:
      When the driver door touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all doors unlock.

  2. The certification ECU (smart key ECU assembly) receives this signal from the door control receiver and changes the entry and start system to the entry unlock mode.

  3. B192480E01
    The certification ECU (smart key ECU assembly) sounds the wireless door lock buzzer and combination meter buzzer to inform the user that the mode has been switched.

    HINT:
    The function only changes the entry unlock mode of the entry and start system. It does not switch the unlocking of the wireless door lock control.


    1. All door unlock mode:

      B189911E02

      HINT:
      1. *1: except China.
      2. *2: For vehicles with the multi-information display.


    2. Driver door unlock mode:

      B189912E02

      HINT:
      1. *1: except China.
      2. *2: For vehicles with the multi-information display.
      3. The above illustration is for LHD vehicles. For RHD vehicles, the left side and right side are reversed.


KEY CANCEL
The key cancel operation disables the following functions:
  1. Entry Unlock/Lock
  2. Key Lock-in Prevention
  3. Memory Call
  4. Entry Back Door Open
  5. Warning
  6. Entry Ignition
  1. The operation procedures are as follows:
    Precondition:
    Engine switch off, driver side door closed and unlocked.

    1. Unlock the driver side door once with the unlock switch of the key.

    2. Open the driver door within 5 seconds.

    3. Unlock the driver side door twice with the unlock switch of the key within 5 seconds.

    4. Perform close → open twice for the driver door within 30 seconds.
      (Driver door: Open condition → Close → Open → Close → Open)

    5. Unlock the driver side door twice with the unlock switch of the key within 5 seconds.

    6. Perform close → open once for the driver door within 30 seconds.
      (Driver door: Open condition → Close → Open)

    7. Close the driver door within 5 seconds.
      When key cancel is activated, the wireless door lock buzzer sounds twice.
      To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once.


WIRELESS BUZZER VOLUME ADJUSTMENT (Click here).
← OPERATION CHECK (from Sep 2011)CUSTOMIZE PARAMETERS (from Jan 2012) →